LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 1999 >> LHS >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Vehicle Communications System >> Symptom Id Tests >> Test 15A: Odometer No Bus Message

Test 15A: Odometer No Bus Message

NOTE: For connector terminal identification and wiring diagrams, see BODY CONTROL COMPUTER - INTRODUCTION article. Perform VERIFICATION TEST VER-1  after each repair.
CAUTION: Always turn ignition off prior to disconnecting any module connector.
  1. Using an external voltmeter, measure voltage between ground and backprobe of DLC terminal No. 2 (Violet/Yellow wire). Turn ignition on. Open all doors and turn on A/C. If voltage is more than 8 volts, go to TEST 15D  . If voltage is less than .5 volt, go to step  3 . If voltage is .5-8 volts, go to next step.
  2. Disconnect both battery cables. Using external ohmmeter, measure resistance between ground and DLC terminal No. 2 (Violet/Yellow wire). If resistance is more than 2000 ohms, go to next step. If resistance is less than 320 ohms, go to TEST 15E  . If resistance is 320-2000 ohms and odometer displays NO BUS, go to TEST 15C  . If resistance is 320-2000 ohms and odometer does not display NO BUS, go to next step.
  3. Turn ignition off. Disconnect both battery cables. Disconnect Overhead Travel Information System (OTIS) module headliner connector at junction block (junction block C11). See Fig 1 . Using external ohmmeter, measure resistance between ground and junction block connector C11 terminal No. 4 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
    Fig 1: Locating Headliner Connector
    G98E00083Courtesy of CHRYSLER CORP.
  4. Disconnect BCM White12-pin connector. Measure resistance between ground and BCM White12-pin connector terminal No. 1 (Violet/Yellow wire). If resistance is 900-1100 ohms, go to next step. If resistance is not 900-1100 ohms, go to TEST 15B  .
  5. Measure resistance between ground and BCM White 12-pin connector terminal No. 2 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  6. Measure resistance between ground and BCM White 12-pin connector terminal No. 7 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  7. Disconnect BCM Blue 16-pin connector. Measure resistance between ground and BCM Blue 16-pin connector terminal No. 9 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  8. Disconnect BCM Gray 14-pin connector. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 14 (Violet/Yellow wire). If resistance is less than 5 ohms, repair open Violet/Yellow wire. If resistance is 5 ohms or more, go to next step.
  9. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 4 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  10. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 5 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15D  .
  11. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 7 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  12. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 12 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  13. Measure resistance between ground and BCM Gray 14-pin connector terminal No. 13 (Violet/Yellow wire). If resistance is 9-11 k/ohms, go to TEST 13C. If resistance is not 9-11 k/ohms, go to TEST 15B  .
  14. Remove BCM from junction block. Measure resistance between ground and junction block 20-pin internal connector. See Figure . If resistance is less than one ohm, replace BCM. If resistance is more than one ohm, replace junction block.