LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 1999 >> LHS >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Vehicle Communications System >> Symptom Id Tests >> Test 15E: Bus Short To Ground

Test 15E: Bus Short To Ground

NOTE: For connector terminal identification and wiring diagrams, see BODY CONTROL COMPUTER - INTRODUCTION article. Perform VERIFICATION TEST VER-1  after each repair.
CAUTION: Always turn ignition off prior to disconnecting any module connector.
  1. Using external ohmmeter, measure resistance between ground and Data Link Connector (DLC) terminal No. 2 (Violet/Yellow wire). Turn ignition off and disconnect Powertrain Control Module (PCM). PCM is located next to air cleaner. If resistance is 9-11 k/ohms, replace PCM. If resistance is not 9-11 k/ohms, go to next step.
  2. Turn ignition off. Disconnect Transmission Control Module (TCM), if equipped. TCM is located at left fenderwell, next to power distribution center in engine compartment. If resistance is 9-11 k/ohms, replace TCM. If resistance is not 9-11 k/ohms, go to next step.
  3. Turn ignition off. Disconnect anti-lock brake controller module. Anti-lock brake controller module is mounted on left inner fender panel. If resistance is 9-11 k/ohms, replace anti-lock brake controller module. If resistance is not 9-11 k/ohms, go to next step.
  4. Turn ignition off. Disconnect Overhead Travel Information System (OTIS) module 6-pin connector. OTIS module is mounted to headliner. If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, replace OTIS module.
  5. Turn ignition off. Disconnect Memory Heated Seat/Mirror Module (MHSMM), if equipped. MHSMM is located under drivers seat. If resistance is 9-11 k/ohms, go to next step. If resistance is not 9-11 k/ohms, replace MHSMM.
  6. Turn ignition off. Disconnect Mechanical Instrument Cluster (MIC). If resistance is 9-11 k/ohms, replace MIC. If resistance is not 9-11 k/ohms, go to next step.
  7. Turn ignition off and wait 5 minutes. Disconnect Air Bag Control Module (ACM) 23-pin connector. ACM is located under center console. If resistance is 9-11 k/ohms, replace ACM. If resistance is not 9-11 k/ohms, go to next step.
  8. Disconnect Sentry Key Immobilizer Module (SKIM) connector. SKIM is located at ignition switch. If resistance is 9-11 k/ohms, replace SKIM. If resistance is not 9-11 k/ohms, go to next step.
  9. Disconnect audio CD player connectors and cable, if equipped. If resistance is 9-11 k/ohms, replace audio CD player. If resistance is not 9-11 k/ohms, go to next step.
  10. Disconnect audio CD player cable, if equipped. If resistance is 9-11 k/ohms, replace audio CD player cable. If resistance is not 9-11 k/ohms, go to next step.
  11. Disconnect radio connector, if equipped. If resistance is 9-11 k/ohms, replace radio. If resistance is not 9-11 k/ohms, go to next step.
  12. Turn ignition off. Disconnect Automatic Temperature Control (ATC) head. If resistance is 9-11 k/ohms, replace ATC. If resistance is not 9-11 k/ohms, go to next step.
  13. Disconnect Body Control Module (BCM) connectors. BCM is connected to junction block. If resistance is 2 k/ohms ohms or more, go to next step. If resistance is less than 2 k/ohms, repair short to ground in bus circuit between BCM Gray 14-pin connector and DLC. See BODY CONTROL COMPUTER - INTRODUCTION article.
  14. Using external ohmmeter, measure resistance between ground and each BCM and junction block connector Violet/Yellow wire. If resistance in any circuit is less than 2 k/ohms, repair appropriate Yellow/Violet wire for short to ground. If resistance in all circuits is 2 k/ohms or more, replace BCM.