LEMON Manuals: Even more car manuals for everyone
Home >> Chrysler >> 1999 >> LHS >> Repair and Diagnosis >> Body & Frame >> Body, Cab Control Systems >> Vehicle Communications System >> Symptom Id Tests >> Test 15D: Bus Short To Battery

Test 15D: Bus Short To Battery

NOTE: For connector terminal identification and wiring diagrams, see BODY CONTROL COMPUTER - INTRODUCTION article. Perform VERIFICATION TEST VER-1  after each repair.
CAUTION: Always turn ignition off prior to disconnecting any module connector.
  1. Ensure voltmeter is still connected from TEST 15A  . Turn ignition off. Disconnect Overhead Travel Information System (OTIS) module, if equipped. OTIS module is mounted to headliner. Turn ignition on. If voltage is more than 8 volts, go to next step. If voltage is 8 volts or less, replace OTIS module.
  2. Turn ignition off. Disconnect OTIS harness at junction block. Turn ignition on. If voltage is more than 8 volts, go to next step. If voltage is 8 volts or less, repair short to battery in OTIS harness.
  3. Turn ignition off. Disconnect Transmission Control Module (TCM), if equipped. TCM is located at left fenderwell, next to power distribution center in engine compartment. Turn ignition on. If voltage is 8 volts or less, replace TCM. If voltage is more than 8 volts, go to next step.
  4. Turn ignition off and disconnect Powertrain Control Module (PCM). PCM is located next to air cleaner. Turn ignition on. If voltage is 8 volts or less, replace PCM. If voltage is more than 8 volts, go to next step.
  5. Turn ignition off. Disconnect anti-lock brake controller module. Anti-lock brake controller module is mounted on left inner fender panel. Turn ignition on. If voltage is 8 volts or less, replace anti-lock brake controller module. If voltage is more than 8 volts, go to next step.
  6. Turn ignition off. Disconnect Body Control Module (BCM) White 12-pin connector. BCM is located on back of junction block. Turn ignition on. If voltage is 8 volts or less, repair short to battery in BCM White 12-pin connector bus circuits. See BODY CONTROL COMPUTER - INTRODUCTION article. If voltage is more than 8 volts, go to next step.
  7. Turn ignition off. Disconnect Memory Heated Seat/Mirror Module (MHSMM), if equipped. MHSMM is located under drivers seat. Turn ignition on. If voltage is 8 volts or less, replace MHSMM module. If voltage is more than 8 volts, go to next step.
  8. Turn ignition off. Disconnect Body Control Module (BCM) Blue 16-pin connector. BCM is located on back of junction block. Turn ignition on. If voltage is 8 volts or less, repair short to battery in BCM Blue 16-pin connector bus circuits. See BODY CONTROL COMPUTER - INTRODUCTION article. If voltage is more than 8 volts, go to next step.
  9. Turn ignition off. Disconnect Automatic Temperature Control (ATC) head. Turn ignition on. If voltage is 8 volts or less, replace ATC head. If voltage is more than 8 volts, go to next step.
  10. Disconnect audio CD player connectors and cable, if equipped. Turn ignition on. If voltage is 8 volts or less, replace audio CD player. If voltage is more than 8 volts, go to next step.
  11. Disconnect audio CD player cable, if equipped. Turn ignition on. If voltage is 8 volts or less, replace audio CD player cable. If voltage is more than 8 volts, go to next step.
  12. Disconnect radio connector, if equipped. Turn ignition on. If voltage is 8 volts or less, replace radio. If voltage is more than 8 volts, go to next step.
  13. Turn ignition off and wait 5 minutes. Disconnect Air Bag Control Module (ACM) 23-pin connector. ACM is located under center console. Turn ignition on. If voltage is 8 volts or less, replace ACM. If voltage is more than 8 volts, go to next step.
  14. Disconnect Sentry Key Immobilizer Module (SKIM) connector. SKIM is located at ignition switch. Turn ignition on. If voltage is 8 volts or less, replace SKIM. If voltage is more than 8 volts, go to next step.
  15. Turn ignition off. Disconnect Mechanical Instrument Cluster (MIC). Turn ignition on. If voltage is 8 volts or less, replace MIC. If voltage is more than 8 volts, go to next step.
  16. Turn ignition off. Disconnect Body Control Module (BCM) Gray 14-pin connector. BCM is located on back of junction block. Turn ignition on. If no voltage exists bus, repair short to battery in BCM Gray 14-pin connector bus circuits. See BODY CONTROL COMPUTER - INTRODUCTION article. If any voltage exists bus, replace BCM.