LEMON Manuals: Even more car manuals for everyone

Front Sub Frame Engine Cradle Removal And Installation/Replacement

Mobile Repair Possible:  No

Overview: 

G15973168Courtesy of VINFAST, LLC
WARNING: Overhead Suspended Load and Falling Parts 
Failure to follow specified procedures may result in death or serious injury when elevated load or components are incorrectly secured/supported.
  • All lifting equipment weight rating must meet or exceed the weight of the vehicle and any contents
  • The lifting equipment must be in good condition and approved for use
  • Only lift the vehicle from the identified lift points
  • Ensure vehicle is stable before performing any work underneath
  • Ensure there are no loose components which may fall
  • Always use personal protective equipment (PPE)
  • Seek assistance when handling larger components
WARNING: Crushing by moving parts 
Failure to follow specified procedures may result in death or serious injury due to front sub frame engine cradle.
  • Secure the component against uncontrolled movement.
  • Always use personal protective equipment (PPE)
  • Ensure vehicle is correctly disabled/powered down to prevent unexpected motion or activation of components.

Removal Procedure: 

  1. Remove high voltage battery. Refer to HIGH VOLTAGE BATTERY REMOVAL AND INSTALLATION/REPLACEMENT
  2. Remove front wheels. Refer to TIRE AND WHEEL REMOVAL AND INSTALLATION
  3. Remove front bumper fascia. Refer to FRONT BUMPER FASCIA REMOVAL AND INSTALLATION/REPLACEMENT
  4. Remove front bumper fascia skid plate. Refer to FRONT BUMPER FASCIA SKID PLATE REMOVAL AND INSTALLATION/REPLACEMENT
    G15973171Courtesy of VINFAST, LLC
  5. Remove 2 bolts (1) on both sides (left hand and right hand crash support brackets).

    Torque: 8 Nm 

  6. Remove 4 nuts (2) on both sides (left hand and right hand crash support brackets).

    Torque: 35 Nm 

    G15973172Courtesy of VINFAST, LLC
  7. Remove 2 bolts (1) on both sides and separate both front lower control arms (2) from steering knuckle (3).
  8. Remove and discard the torque prevailing nut.

    Replace with new only. 

    Torque: 78 Nm 

    G15973173Courtesy of VINFAST, LLC
  9. Remove 2 nuts (1) on both sides and separate steering linkage (2) from steering knuckle (3).
  10. Remove and discard the torque prevailing nut.

    Replace with new only. 

    Torque: 80 Nm 

    G15973174Courtesy of VINFAST, LLC
  11. Disconnect the intermediate steering shaft (1) from the steering gear. Refer to INTERMEDIATE STEERING SHAFT REMOVAL AND INSTALLATION/REPLACEMENT .
    G15973175Courtesy of VINFAST, LLC
  12. Remove 2 nuts (1) on both sides and separate coupling rod (2) from stabilizer (3).
  13. Remove and discard the torque prevailing nut.

    Replace with new only. 

    Torque: 100 Nm 

    G15973176Courtesy of VINFAST, LLC
  14. Hold the electric motor from above with a suitable motor holder.
  15. Remove the bolt (1) and separate motor holder (2) from unit support (3).
  16. Remove and discard the torque prevailing bolt.

    Replace with new only. 

    Torque - First Pass: 88 Nm 

    G15973177Courtesy of VINFAST, LLC
  17. Disconnect the electrical plug connection (1) to the steering gear.
    G15973178Courtesy of VINFAST, LLC

    Remove note: Using a suitable lifting/supporting device for the front cradle, support the cradle before removing the securing bolts to the body. 

  18. Remove 4 bolts (1).
  19. Remove and discard the torque prevailing bolt.

    Replace with new only. 

    Torque - First Pass: 250 Nm 

    Torque - Final Pass: 90° Rotation Angle 

    G15973179Courtesy of VINFAST, LLC
  20. Gently lower the front sub frame engine cradle (1) downwards using the lifting/supporting jack.

Replacement Procedure: 

  1. Rebuild front sub frame level sensor. Refer to FRONT SUB FRAME LEVEL SENSOR REMOVAL AND INSTALLATION/REPLACEMENT 
  2. Rebuild front sub frame longitudinal beam. Refer to FRONT SUB FRAME LONGITUDINAL BEAM REMOVAL AND INSTALLATION/REPLACEMENT 
  3. Rebuild steering gear. Refer to STEERING GEAR REMOVAL AND INSTALLATION/REPLACEMENT
  4. Rebuild front anti roll bar. Refer to FRONT ANTI ROLL BAR REMOVAL AND INSTALLATION/REPLACEMENT 
  5. Rebuild front lower control arm. Refer to FRONT LOWER CONTROL ARM REMOVAL AND INSTALLATION/REPLACEMENT 

Installation Procedure: 

NOTE: Safety-relevant procedure step 
Failure to discard the specified component(s) may cause damage to the vehicle or vehicle components.
  • Fasteners highlighted as torque prevailing must be discarded and not re-used
  • Replace with new nuts and bolts only.
  1. Installation is the reverse of removal procedure, noting the following.

    All fasteners must be tightened to torque specification! 

  2. Install front bumper fascia. Refer to FRONT BUMPER FASCIA REMOVAL AND INSTALLATION/REPLACEMENT
  3. Install front tire. Refer to TIRE AND WHEEL REMOVAL AND INSTALLATION
  4. Install front bumper fascia skid plate. Refer to FRONT BUMPER FASCIA SKID PLATE REMOVAL AND INSTALLATION/REPLACEMENT
  5. Enable HV-System. Refer to HV-SYSTEM DISABLING/ENABLING
  6. Carry out wheel alignment. Refer to WHEEL ALIGNMENT MEASUREMENT AND SPECIFICATIONS