LEMON Manuals: Even more car manuals for everyone
Home >> Lexus >> 2001 >> ES 300 >> Repair and Diagnosis >> Brakes >> Traction Control >> Anti-Lock Brake System (With VSC) - Diagnosis >> Pre-Check

Anti-Lock Brake System (With VSC) - Diagnosis: Pre-Check

  1. DIAGNOSIS SYSTEM 
    1. Check the indicator. When the ignition switch is turned ON, check that the ABS warning light comes on for 3 seconds.
      NOTE: If the indicator check result is not normal, proceed to the troubleshooting for the ABS WARNING LIGHT CIRCUIT  .
    2. Fig 1: Locating ABS Warning Light
      G03138628Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 2: Disconnecting Short Pin From DLC1
      G03138629Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. In case of not using LEXUS hand-held tester: Check the DTC.
      1. Disconnect the short pin from the DLC1.
      2. Using SST (SST 09843-18020 or 09843-18040), connect terminals Tc and E1 of the DLC1, or terminals Tc and CG of the DLC3.
      3. Turn the ignition switch ON.
      4. Read the DTC from the ABS warning light on the combination meter.
        NOTE:
      5. Fig 3: Identifying DLC1 & DLC3 Connector Terminals
        G03138630Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      6. Codes are explained in the DIAGNOSTIC TROUBLE CODE INDEX  table .
      7. After completing the check, disconnect terminals Tc and E1 of the DLC1, or terminals Tc and CG of the DLC3, and turn off the display.

      If 2 or more malfunctions are indicated simultaneously the lowest numbered DTC will be displayed first.

    4. Fig 4: Identifying Diagnostic Trouble Code Blinking Patterns
      G03138631Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. In case of using LEXUS hand-held tester: Check the DTC.
      1. Connect the LEXUS hand-held tester to the DLC3.
      2. Turn the ignition switch ON.
      3. Read the DTC by following the prompts on the tester screen.
      NOTE: Please refer to the LEXUS hand-held tester operator's manual for further details.
    6. Fig 5: Connecting LEXUS Hand-Held Tester To DLC3
      G03138632Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. In case of not using LEXUS hand-held tester: Clear the DTC.
      1. Using SST (SST 09843-18020 or 09843-18040), connect terminals Tc and E1 of the DLC1 or terminals Tc and CG of the DLC3, and remove the short pin from the DLC1.
      2. Turn the ignition switch ON.
      3. Clear the DTC stored in the ECU by depressing the brake pedal 8 or more times within 5 seconds.
      4. Fig 6: Depressing Brake Pedal To Clear DTC
        G03138633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      5. Check that the warning light shows the normal code.
      6. Remove the SST (SST 09843-18020 or 09843-18040) from the DLC1 or the DLC3.
      7. Connect the short pin to the DLC1.
      NOTE: The DTC stored in the ECU will be not erased when the battery terminal is disconnected for the troubleshooting.
    8. Fig 7: Connecting Short Pin To DLC1
      G03138634Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. In case of using LEXUS hand-held tester: Clear the DTC.
      1. Connect the LEXUS hand-held tester to the DLC3.
      2. Turn the ignition switch ON.
      3. Operate the LEXUS hand-held tester to erase the codes. (See the LEXUS hand-held tester operator's manual.)
    10. Fig 8: Connecting LEXUS Hand-Held Tester To DLC3
      G03138635Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. Test Mode: SENSOR SIGNAL CHECK 
    NOTE: If the ignition switch is turned from ON to ACC or LOCK during test mode, DTC will be erased.
    1. In case of not using LEXUS hand-held tester: Check the sensor signal.
      1. Turn the ignition switch OFF.
      2. Using SST (SST 09843-18020 or 09843-18040), connect terminals Ts and E1 of the DLC1 or terminals Ts and CG of the DLC3.
      3. Fig 9: Identifying DLC1 & DLC3 Connector Terminals
        G03138636Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Start the engine.
      5. Check that the ABS warning light blinks.
        NOTE: If the ABS warning light does not blink, inspect the ABS WARNING LIGHT CIRCUIT  and TS TERMINAL CIRCUIT  .
      6. Fig 10: ABS Warning Light Blinking Pattern
        G03138637Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      7. Keep the vehicle in the stationary condition on the flat place for 1 sec. or more.
      8. Keeping the vehicle in the stationary condition and the brake pedal in free condition for 1 sec. or more, continue to depress the brake pedal with 147 N (15 kgf, 33 lbf) or more for 1 sec. or more.
      9. Keeping the vehicle in the stationary condition, depress the brake pedal with 98 N (10 kgf, 22 lbf) or more quickly.
        NOTE: The above mentioned condition comes into existence, the ABS warning light comes ON for 3 seconds.
      10. Drive the vehicle straight forward. When driving the vehicle at the speed faster than 45 km/h (28 mph) for several seconds, check that the ABS warning light comes off.
        NOTE: There is a case that the sensor check is not completed if the vehicle has its rear wheels spun or its steering wheel steered during this check.
      11. Stop the vehicle.
      12. Using SST (SST 09843-18020 or 09843-18040), connect terminals Tc and E1 of the DLC1 or terminals Tc and CG of the DLC3.
      13. Read the number of blinks of the ABS warning light.
        NOTE:
        • See the SENSOR SIGNAL CHECK DIAGNOSTIC CODES  table .
        • If every sensor is normal, a normal code is output (A cycle of 0.25 seconds ON and 0.25 seconds OFF is repeated).
        • If 2 or more malfunctions are indicated simultaneously, the lowest numbered code will be displayed first.
      14. Fig 11: Malfunction Code Blinking Pattern For DTC 72 & DTC 76
        G03138638Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      15. After doing the check, disconnect the SST (SST 09843-18020 or 09843-18040) from terminals Ts and E1 , Tc and E1 of the DLC1 or terminals Ts and CG, Tc and CG of the DLC3, and turn the ignition switch OFF.
    2. In case of using LEXUS hand-held tester: Check the sensor signal.
      1. Connect the LEXUS hand-held tester to the DLC3.
      2. Do step  3 through  9 .
      3. Read the DTC by following the prompts on the tester screen.
      NOTE: Please refer to the LEXUS hand-held tester operator's manual for further details.
      Fig 12: Connecting LEXUS Hand-Held Tester To DLC3
      G03138639Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      SENSOR SIGNAL CHECK DIAGNOSTIC CODES

      Code No. Diagnosis Trouble Area
      C1271/71 Low output voltage of right front speed sensor
      • Right front speed sensor
      • Sensor installation
      • Sensor rotor
      C1272/72 Low output voltage of left front speed sensor
      • Left front speed sensor
      • Sensor installation
      • Sensor rotor
      C1273/73 Low output voltage of right rear speed sensor
      • Right rear speed sensor
      • Sensor installation
      • Sensor rotor
      C1274/74 Low output voltage of left rear speed sensor
      • Left rear speed sensor
      • Sensor installation
      • Sensor rotor
      C1275/75 Abnormal change in output voltage of right front speed sensor
      • Right front speed sensor rotor
      C1276/76 Abnormal change in output voltage of left front speed sensor
      • Left front speed sensor rotor
      C1277/77 Abnormal change in output voltage of right rear speed sensor
      • Right rear speed sensor rotor
      C1278/78 Abnormal change in output voltage of left rear speed sensor
      • Left rear speed sensor rotor
      C1279/79 (1) Deceleration sensor is faulty
      • Deceleration sensor
      • Sensor installation
      C1281/81(1) Master cylinder pressure sensor output signal is faulty
      • Master cylinder pressure sensor
      (1) w/VSC only
  3. w/VSC: DECELERATION SENSOR OPERATION DIAGNOSIS SYSTEM 
    CAUTION: While checking the deceleration sensor operating diagnosis system, ABS does not work and brake system works as a conventional brake system.
  4. w/VSC: DECELERATION SENSOR CHECK 
    1. Connect 3 dry batteries of 1.5 V in series.
    2. Connect VGS terminal to the batteries' positive (+) terminal, and GGND terminal to the batteries' negative (-) terminal, apply about 4.5 V between VGS - GGND terminals.
      NOTE:
      • When inspecting deceleration sensor, remove it with the bracket together. Do not remove the sensor from the bracket. When replacing deceleration sensor, replace the sensor with it assembled to the bracket assembly.
      • Do not apply voltage of 6 V or more to terminals VGS and GGND.
    3. Check the output voltage of GL1 and GL2 terminals.
      Fig 13: Checking Deceleration Sensor (W/VSC)
      G03138640Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      GL1 & GL2 TERMINALS VOLTAGE SPECIFICATIONS

      Symbols Condition Standard Value
      GL1 Horizontal About 2.3 V
      GL1 Lean forward 0.4 V-about 2.3 V
      GL1 Lean rearward About 2.3 V-4.1 V
      GL2 Horizontal About 2.3 V
      GL2 Lean forward About 2.3 V-4.1 v
      GL2 Lean rearward 0.4 V-about 2.3 V
    NOTE:
    • If the sensor is tilted too much it may show the wrong value.
    • If dropped, the sensor should be replaced with a new one.
    • The sensor removed from the vehicle should not be placed upside down.