LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Mirai XLE >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Fuel System - Inspection >> Fuel System >> Disposal [11/2020 - ] >> Procedure

Disposal [11/2020 - ]: Procedure

  1. DISPOSE OF HYDROGEN TANK ASSEMBLY 
    WARNING:
    • To prevent static electricity, spray water on the hydrogen tank assembly and around the work area.
    • Before performing work procedures, touch a metal object in contact with the ground in order to discharge any static electricity from your body.
    • While releasing compressed hydrogen gas, the temperature inside the tank decreases and frost may form on the outside. Do not touch tanks when frost has formed on them.
      GTY1005097Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    • Touching tanks on which frost has formed could result in burn-like injuries due to frostbite.
    1. Secure the hydrogen tank assembly to the work table with the belt in the orientation shown in the illustration.
      GTY1163308Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Belt
    2. Using an 8 mm socket hexagon wrench, apply the specified torque to the adjustment bolt, and check that the manual valve is closed.
      GTY1167598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Manual Valve Closed
      *b Adjustment Bolt

      Torque: 25 N*m (255 kgf*cm, 18 ft.*lbf) 

      NOTE:

      Rotate the manual valve adjustment bolt, taking care not to damage the hexagonal portion. Do not damage the hexagonal portion of the adjustment bolt as the manual valve is the part that cuts off the pressure from the hydrogen tank assembly, and this would make it difficult to discharge compressed hydrogen gas from the hydrogen tank assembly.

    3. Using a screwdriver, remove the resin around the release valve of the hydrogen tank assembly.
      GTY1165014Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Resin
      *b Screwdriver
    4. Using an 8 mm socket hexagon wrench, slowly loosen the release valve of the hydrogen tank valve assembly to discharge the compressed hydrogen gas.
      GTY1167095Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • The compressed hydrogen gas left in the hydrogen tank valve assembly will be discharged, so slowly loosen until no more compressed hydrogen gas comes out.
      • If compressed hydrogen gas continues to be discharged, close the release valve of the hydrogen tank valve assembly and reconfirm that the manual valve of the hydrogen tank assembly is closed.
    5. Using an 8 mm socket hexagon wrench, slowly rotate the adjustment bolt counterclockwise to open the manual valve of the hydrogen tank assembly until compressed hydrogen gas is no longer discharged.
      GTY1162389Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Manual Valve Open
      *b Adjustment Bolt
      NOTE:
      • Rotate the manual valve adjustment bolt, taking care not to damage the hexagonal portion. Do not damage the hexagonal portion of the adjustment bolt as the manual valve is the part that cuts off the pressure from the hydrogen tank assembly, and this would make it difficult to discharge compressed hydrogen gas from the hydrogen tank assembly.
      • Do not rotate the adjustment bolt 4 or more turns, as this may damage the manual valve.
    6. Secure the hydrogen tank assembly with the belt in the orientation shown in the illustration.
      GTY1166729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Belt
    7. Using a T20 "TORX" socket wrench, disconnect the 2 screws and disconnect the wire harness from the hydrogen tank valve assembly.
      GTY1004438Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Using a 13 mm socket wrench, install SST (hydrogen tank holding tool) to the hydrogen tank valve assembly.
      GTY1004855Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a SST Installation Area
      • SST: 09403-62021 
        1. 09403-00010

      Torque: 28 N*m (286 kgf*cm, 21 ft.*lbf) 

    9. Remove the hydrogen tank valve assembly.
      1. While holding SST (hydrogen tank holding tool), rotate the hydrogen tank valve assembly to loosen the valve.
        GTY1004513Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Hold
        Turn

        Tightening torque (reference)

        Hydrogen tank valve assembly 

        485 N*m (4946 kgf*cm, 358 ft.*lbf)

        WARNING:

        Because the tightening torque of the hydrogen tank valve assembly is extremely high, perform this operation with 2 people.

      2. Remove SST (hydrogen tank holding tool) from the hydrogen tank valve assembly.
        GTY1004690Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Remove the hydrogen tank valve assembly.
        GTY1004430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Remove the hydrogen tank assembly from the work table.
    11. Soak the interior of the hydrogen tank assembly with water.
      1. Spray water into the hydrogen tank assembly through the valve installation hole as shown in the illustration.
        GTY1004429Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        NOTE:

        To prevent static electricity from being generated when blowing compressed air into the hydrogen tank assembly through the valve installation hole, make sure to perform this procedure.

        HINT: 

        Water filling amount: Approximately 10 liters (10.6 US qts, 8.8 Imp. qts).

      2. Rotate the hydrogen tank assembly 1 or more times so that the water is completely spread throughout the inside of the hydrogen tank assembly.
        GTY1004650Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Rotate
        NOTE:

        To prevent static electricity from being generated when blowing compressed air into the hydrogen tank assembly through the valve installation hole, make sure to perform this procedure.

    12. Use a belt to secure the hydrogen tank assembly vertically.
      GTY1004680Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Belt
      WARNING:

      Because the hydrogen tank assembly is extremely heavy, be sure to perform these procedures with 2 people or more.

      NOTE:

      To prevent the hydrogen tank assembly from falling over, use a belt to secure the hydrogen tank assembly.

    13. Measure the hydrogen gas concentration.
      1. Before measuring the hydrogen gas concentration, blow compressed air into the hydrogen tank assembly through the hydrogen tank valve installation hole.
        GTY1004424Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        HINT: 

        Perform in order to force out hydrogen gas that may remain in the hydrogen tank assembly and release it into the atmosphere.

      2. If there are any water droplets, etc. adhering to the measurement locations, wipe them away before measuring the hydrogen gas concentration.
        NOTE:

        Performing the measurement while any water droplets, etc. are adhering could damage the hydrogen gas detector.

      3. Using SST and a hydrogen gas detector, measure the hydrogen gas concentration at the location shown in the illustration.
        GTY1005061Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a Hydrogen Gas Detector
        Hydrogen Concentration Measurement Area
        • SST: 09401-62020 

        Specified value

        Less than 500 ppm

        HINT: 

        • If the hydrogen tank assembly is left standing vertically for approximately 1 day, the hydrogen concentration becomes 500 ppm or less. (Make sure to leave it in an area with good ventilation for at least 8 hours.)
        • Immediately after the measurement starts, the measured value may be unstable.
        • Measure the gas concentration for approximately 10 seconds continuously.
    14. Place the hydrogen tank assembly on wheel chocks or similar.
      GTY1004490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Wheel Chocks
    15. Using a drill, open 2 or more holes on the hydrogen tank assembly.
      GTY1004880Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Hole diameter

      12.5 mm (0.492 in.) or more

      WARNING:
      • Make sure to wear protective glasses when drilling the holes.
        GTY1004876Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      • Drilling the holes without wearing protective glasses could result in a serious accident.

      HINT: 

      Perform this procedure so that the hydrogen tank assembly is not reused.

    16. Destroy the threads of the valve installation hole of the hydrogen tank assembly as shown in the illustration.
      GTY1005074Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Perform this procedure so that the hydrogen tank assembly is not reused.

    17. Destroy the threads of the valve of the hydrogen tank assembly as shown in the illustration.
      GTY1004872Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Perform this procedure so that the hydrogen tank valve assembly is not reused.