LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2010 >> Sienna LE, FWD >> Repair and Diagnosis >> Engine Mechanical >> Fuel System >> Engine Fuel System (Service Information) >> Fuel Pump >> Disassembly >> Disassembly

Fuel Pump: Disassembly: Disassembly

  1. REMOVE FUEL TANK TO FILLER PIPE HOSE  See step  9
  2. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY 
    Fig 1: Identifying Fuel Tank Main Tube, Joint Clip, Nylon Tube, Fuel Tube Joint, Fuel Suction Plate & O - Ring
    GTY231687Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the tube joint clip, and pull out the fuel main tube.
      NOTE:
      • Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary
      • Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.
      • Do not use any tool in this operation.
      • Do not bend or twist the nylon tube. Protect the connector by covering it with a vinyl or plastic bag.
      • When the pipe and connector are stuck, push and pull the connector to release and pull the connector out carefully.
    2. Unfasten the 4 claws and remove the fuel tank main tube from the fuel tank.
      Fig 2: Locating Fuel Tank Main Tube & Claws
      GTY237944Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE 
    Fig 3: Identifying SST, Fuel Pump Rib & Gauge Retainer
    GTY232469Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using SST, loosen the fuel pump gauge retainer.
      • SST: 09808-14020 
        • 09808-01410
        • 09808-01420
        • 09808-01430

      HINT: 

      A rib on the fuel pump gauge retainer can be fitted into a tip of SST.

    2. Remove the fuel pump gauge retainer.
    3. Remove the fuel suction tube assembly with pump and gauge and the fuel suction tube set gasket from the fuel tank.
      NOTE:

      Be careful not bend the arm of the fuel sender gauge.

  4. REMOVE FUEL SENDER GAUGE ASSEMBLY 
    Fig 4: Disconnecting Fuel Sender Gage Connector
    GTY211602Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the fuel sender gauge connector.
    2. Unlock the fuel sender gauge and slide it to remove.
  5. REMOVE FUEL SUCTION PLATE SUB-ASSEMBLY 
    Fig 5: Identifying Fuel Suction Plate, Taped Screwdriver & Snap Claws
    GTY236984Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver with the tip wrapped in tape, disconnect the 4 snap-claws from the claw holes and remove the fuel suction plate.
      NOTE:

      Do not damage the fuel suction plate and the No. 1 fuel suction support.

  6. REMOVE FUEL PUMP 
    Fig 6: Identifying Fuel Pump, Taped Screwdriver, Connector & Claws
    GTY221036Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the fuel pump connector.
    2. Using a small screwdriver with the tip wrapped in tape, disconnect the 2 claws from the claw holes and pull out the fuel pump.
      NOTE:

      Do not damage the fuel pump and the fuel suction plate.

    3. Remove the O-ring and the fuel pump spacer from the fuel pump.
  7. REMOVE FUEL FILTER ASSEMBLY 
    Fig 7: Identifying Fuel Filter, Screwdriver, Fuel Pump & Clip
    GTY236985Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a small screwdriver, pry out the clip.
    2. Remove the fuel filter assembly from the fuel pump.
  8. REMOVE NO. 1 FUEL TUBE JOINT 
    Fig 8: Identifying Fuel Tube Joint, Tape, Connector & Snap Claw
    GTY236986Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the connector.
    2. Using a screwdriver with the tip wrapped in tape, disconnect the snap-claw from the claw hole and pull out the No. 1 fuel tube joint.
      NOTE:

      Do not damage the No. 1 fuel tube joint and the fuel suction plate.

  9. REMOVE FUEL PUMP HARNESS 
    Fig 9: Identifying Fuel Pump Harness & No. 1 Fuel Tube Joint
    GTY234335Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the fuel pump harness from the No. 1 fuel tube joint.
  10. REMOVE FUEL PRESSURE REGULATOR ASSEMBLY 
    Fig 10: Removing Fuel Pressure Regulator, Clip, Fuel Suction Plate & O - Rings
    GTY235640Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the clip.
    2. Pull out the fuel pressure regulator from the fuel suction plate.
    3. Remove the 2 O-rings from the fuel pressure regulator.