LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2010 >> Sienna LE, AWD >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Engine Fuel System (Service Information) >> Fuel Injector >> Removal >> Removal

Fuel Injector: Removal: Removal

  1. DISCHARGE FUEL SYSTEM PRESSURE 

    HINT: 

    Refer toPRECAUTION .

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
  3. REMOVE NO. 1 ENGINE UNDER COVER 
  4. DRAIN ENGINE COOLANT  . Refer toREPLACEMENT - Step 3
  5. REMOVE FRONT WIPER ARM HEAD CAP  . Refer toREMOVAL - Step 1
  6. REMOVE FRONT WIPER ARM RH  . Refer toREMOVAL - Step 2
  7. REMOVE FRONT WIPER ARM LH  . Refer toREMOVAL - Step 3
  8. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  . Refer toREMOVAL - Step 4
  9. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY  . Refer toREMOVAL - Step 5
  10. REMOVE NO. 1 COWL TOP TO COWL BRACE INNER 
    1. Remove the 2 bolts and the No. 1 cowl top to cowl brace inner.
      Fig 1: Identifying Cowl Top, Cowl Brace Inner & Bolts
      GTY237833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE COWL TOP PANEL SUB-ASSEMBLY OUTER FRONT 
    Fig 2: Identifying Cowl Top Panel Outer Front, Harness Clamp, Fuel Resistor Connector & Bolts
    GTY237834Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the wire harness clamp.
    2. Disconnect the fuel pump resistor connector.
    3. Remove the 7 bolts and the cowl top panel outer front.
  12. REMOVE V-BANK COVER SUB-ASSEMBLY  . Refer toREMOVAL - Step 19
  13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY 
    1. Disconnect the 3 vacuum hoses.
      Fig 3: Identifying Air Cleaner & Vacuum Hoses
      GTY141099Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the No. 2 ventilation hose and air cleaner hose band.
      Fig 4: Identifying Air Cleaner, No. 2 Ventilation Hose & Air Cleaner Hose Band
      GTY144387Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the vacuum hose (EVAP) from the air cleaner hose.
    4. Remove the 2 bolts and air cleaner cap sub-assembly.
      Fig 5: Identifying Air Cleaner, Cap Sub-Assembly & Bolts
      GTY237899Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE INTAKE AIR SURGE TANK ASSEMBLY 
    1. Disconnect the 2 water by-pass hoses from the throttle with motor body assembly. (*1)
      Fig 6: Identifying Intake Air Surge Tank, Clamp, Throttle & Motor Body Assembly
      GTY210819Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the fuel vapor feed hose assembly.(*2)
    3. Disconnect the throttle with motor body assembly connector and clamp. (*3)
    4. Disconnect the No. 1 ventilation hose. (*4)
      Fig 7: Identifying Intake Air Surge Tank Union & Valve Hose
      GTY237835Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Disconnect the union to check valve hose. (*5)
    6. Disconnect the connector.
      Fig 8: Identifying Intake Air Surge Tank Connector
      GTY121700Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Using a 5 mm socket hexagon wrench, remove the 4 bolts. (*1)
      Fig 9: Identifying Air Surge Tank, Nuts & Bolts
      GTY237464Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Remove the 2 nuts, 2 bolts, and intake air surge tank. (*2)
    9. Remove the gasket from the intake air surge tank.
  15. DISCONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Remove the No. 2 fuel pipe clamp.
      Fig 10: Identifying No. 2 Fuel Pipe Clamp, Tube Connector, Nylon Tube, Pipe & O - Ring
      GTY121632Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Pinch the tube connector and pull out the fuel pipe.
      NOTE:
      • Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector as necessary.
      • It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
      • Only disconnect the quick connector by hand.
      • Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
      • If the pipe and the connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off the pipe carefully.
  16. REMOVE FUEL INJECTOR ASSEMBLY 
    1. Disconnect the 6 fuel injector connectors.
      Fig 11: Identifying Fuel Injector Assembly Connectors
      GTY139844Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 5 bolts and fuel delivery pipe sub-assembly together with the 6 fuel injectors.
      Fig 12: Identifying Fuel Delivery Pipe & Fuel Injectors
      GTY139208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Be careful not to drop the fuel injectors when removing the fuel delivery pipe sub-assembly.

    3. Remove the 6 injector vibration insulators from the intake manifold.
      Fig 13: Identifying Injector Vibration Insulators & Intake Manifold
      GTY171257Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Pull out the fuel injectors from the fuel delivery pipe sub-assembly.
      Fig 14: Identifying Fuel Injector & Fuel Delivery Pipe
      GTY124446Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 6 O-rings from the fuel injectors.
      Fig 15: Identifying Injectors O-Rings
      GTY146476Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002