LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2010 >> RAV4 Base, 2.5 F, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 348 (Can Communication System (Diagnostics - Introduction)) >> Can Communication System >> Fail-Safe Chart >> Fail-Safe Chart

Fail-Safe Chart

WARNING: This page is about a different car, the 2010 Toyota 4Runner. However, it is still accessible from the selected car via links, so may be relevant.
  1. FAIL-SAFE FUNCTION 
    1. When communication fails in any of the main wires (communication lines) due to a short circuit or other causes, the fail-safe function, which is specified for each system, operates to prevent the system from malfunctioning.
    2. The table below shows the effects on each system when communication is impossible. For further details, refer to each system.
      Function
      1. Control Master
      2. System Related
      Fail-safe Function System Behavior User Notification Diagnosis Code
      Engine-related Indicators
      (The system estimates the oil deterioration level and the indicators indicate on the meter that an oil change is necessary, etc.)
      1. ECM
      2. Combination meter assembly)
      • The indicator lights do not turn on.
      • Cannot clear the meter display.
      The engine-related indicator lights do not turn on. -
      Electrical Load Control
      (Performs idle up according to the electrical load.)
      1. ECM
      2. Air conditioning amplifier assembly, Main body ECU (multiplex network body ECU)
      Idle up according to the electrical load is not performed. The idle speed changes. -
      Air Conditioning-linked Control
      (Performs idle up according to the compressor load.)
      1. ECM
      2. Air conditioning amplifier assembly, Power management control ECU
      Air conditioning-linked control does not operate. The air conditioning does not operate. -
      PTC Heater
      (Performs idle up according to requests from the PTC heater or heater system.)
      1. ECM
      2. Air conditioning amplifier assembly
      The PTC heater does not operate. The idle speed changes and heater performance deteriorates. -
      Eco Driving Indicator
      (Displays information to the driver to encourage "ecodriving".)
      1. ECM
      2. Combination meter assembly
      • The indicator light does not turn on.
      • The display of all information stops.
      The eco driving indicator light does not turn on. -
      Integrated Control (VSC)
      (Estimates the driver requested torque based on accelerator pedal operation and performs torque characteristic control according to driving conditions so that drivability, acceleration performance and acceleration feeling are improved.)
      1. ECM
      2. Master cylinder solenoid (skid control ECU), Yaw rate sensor assembly, Spiral cable sub-assembly (steering angle sensor)
      Integrated control is not performed. Nothing -
      ECT System Indicators
      (Indicate shift position, states of switches, system modes, etc.)
      1. ECM
      2. Combination meter assembly, Drive monitor switch
      - ECT system indicator lights do not turn on. -
      AI-SHIFT Control
      (Controls the A/T in order to improve engine braking power and acceleration feel.)
      1. ECM
      2. Master cylinder solenoid (skid control ECU)
      AI-SHIFT control does not operate. Nothing -
      Coast Downshift
      (Changes the coast downshift point based on the air conditioning load and performs upshift delay according to air conditioning or heater requests.)
      1. ECM
      2. Air conditioning amplifier assembly
      Coast downshift does not operate. Coast downshift shock becomes stronger. -
      Cruise Control
      (Adjusts the engine throttle valve opening amount automatically to maintain the vehicle speed.)
      1. ECM
      2. Master cylinder solenoid (skid control ECU), Combination meter assembly
      Cruise control does not operate. The CRUISE main indicator light and CRUISE SET indicator light blink. -
      ABS Control
      (Controls the ABS according to the yaw rate sensor signal.)
      1. Master cylinder solenoid (skid control ECU)
      2. Yaw rate sensor assembly
      The ABS does not operate. The ABS indicator light turns on. U0073
      U0123
      U0124
      TRC Control
      (Controls the brakes and engine torque during acceleration slip.)
      1. Master cylinder solenoid (skid control ECU)
      2. ECM
      TRC does not operate. The TRC indicator light turns on. U0073
      U0100
      VSC Control
      (Controls VSC according to yaw rate sensor and steering angle sensor signals.)
      1. Master cylinder solenoid (skid control ECU)
      2. ECM, Yaw rate sensor assembly, Spiral cable sub-assembly (steering angle sensor)
      VSC does not operate. The VSC indicator light turns on. U0073
      U0100
      U0123
      U0124
      Steering Sensor
      (Detects the steering wheel angle.)
      1. Master cylinder solenoid (skid control ECU)
      2. Spiral cable sub-assembly (steering angle sensor)
      - The VSC indicator light turns on. -
      Vehicle Speed Information Input
      (Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.)
      1. Power steering ECU assembly
      2. Master cylinder solenoid (skid control ECU)
      Changes to the 40 km/h (25 mph) assist map to perform control. The PPS indicator light turns on. U0073
      Steering Wheel Angle Information Input
      (Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.)
      1. Power steering ECU assembly
      2. Spiral cable sub-assembly (steering angle sensor)
      Steering angle is fixed at 0 degrees and the steering angle speed is fixed at 360 degrees per second. The PPS indicator light turns on. U0073
      Engine Speed Information Input
      (Controls solenoid current [PPS solenoid] according to the vehicle speed, steering angle, steering speed and engine speed.)
      1. Power steering ECU assembly
      2. ECM
      Control is performed using a fixed value of 0 rpm. The PPS indicator light turns on. U0073
      TC DTC Output Service
      (Outputs a DTC in response to a DTC output request from the combination meter assembly.)
      1. Combination meter assembly
      2. ECM, Center airbag sensor assembly
      The TC service function stops. Nothing -
      Event Data Recorder (EDR)
      (Records conditions such as the vehicle speed, the amount the accelerator pedal is depressed and the shift lever position when the event data recorder recording conditions are met.)
      1. Center airbag sensor assembly
      2. ECM, Combination meter assembly
      - Nothing -
      SRS Warning Light Control
      (Turns the warning light on/off.)
      1. Combination meter assembly
      2. Center airbag sensor assembly
      The SRS warning light turns on. The SRS warning light turns on. -
      Collision Detection Signal (for Fuel-cut)
      (Notifies the system of a collision in order to perform fuel-cut when a vehicle collision occurs.)
      1. ECM
      2. Center airbag sensor assembly
      The fuel-cut function used when a collision occurs is stopped. Nothing -
      Seat Belt Warning Light Control
      (Turns the seat belt warning light on/off.)
      1. Combination meter assembly, Main body ECU (multiplex network body ECU)
      2. Center airbag sensor assembly
      The seat belt warning light does not operate. Nothing -
      Air Conditioning System Control
      (Controls the air conditioning according to the engine coolant temperature information, controls the viscous heater operation according to the viscous heater operation permission information and controls the PTC heater operation according to the PTC heater operation permission information.)
      1. Air conditioning amplifier assembly
      2. ECM, Combination meter assembly, Navigation receiver assembly, Main body ECU (multiplex network body ECU)
      • Maintains the current conditions.
      • PTC control does not operate.
      Nothing U0100
      U0142
      U0155
      Speedometer
      (Controls the speedometer according to the vehicle speed signals.)
      1. Combination meter assembly
      2. Master cylinder solenoid (skid control ECU)
      0 km/h (0 mph) is indicated. Behavior during a communication failure alerts the user. U0129
      Tachometer
      (Controls the tachometer according to the engine speed signals.)
      1. Combination meter assembly
      2. ECM
      0 rpm is indicated. Behavior during a communication failure alerts the user. U0100
      Engine Coolant Temperature Gauge
      (Controls the temperature gauge according to the temperature signals.)
      1. Combination meter assembly
      2. ECM
      The temperature gauge needle is at the middle of the "C" mark or below. Nothing U0100
      Fuel Receiver Gauge
      (Controls the fuel gauge according to the vehicle condition determined by the ST signal, vehicle speed signal and fuel amount.)
      1. Combination meter assembly
      2. ECM, Master cylinder solenoid (skid control ECU)
      • Operates the same as when the vehicle is stopped.
      • Operates with ST set to off.
      Nothing U0100
      U0129
      ODO/TRIP Meter
      (Calculates and indicates the driven distance according to the pulse count of the vehicle speed pulse signal.)
      1. Combination meter assembly
      2. Master cylinder solenoid (skid control ECU)
      The calculation stops and the last displayed value remains. Nothing U0129
      Shift Display
      (Displays the shift information according to the shift position signal.)
      1. Combination meter assembly
      2. ECM
      The shift display turns off. Nothing U0100
      Telltale
      (Controls indicator illumination and blinking according to the CAN signals and direct line input signals.)
      1. Combination meter assembly
      2. ECM, Master cylinder solenoid (skid control ECU), Power steering ECU assembly, Center airbag sensor assembly, Certification ECU, Main body ECU (multiplex network body ECU), Four wheel drive control ECU, Stabilizer control ECU
      - The indicator or warning lights turn on. U0100
      U0129
      U0131
      U0151
      Buzzer
      (Controls the sounding of buzzers according to the CAN signals and direct line input signals.)
      1. Combination meter assembly
      2. ECM, Master cylinder solenoid (skid control ECU), Center airbag sensor assembly, Certification ECU, Main body ECU (multiplex network body ECU), Four wheel drive control ECU
      - Buzzer sounds. U0100
      U0129
      U0151
      Drive Monitor
      (Performs calculations and displays drive monitor information according to the fuel injection volume and pulse count of the vehicle pulse signal.)
      1. Combination meter assembly
      2. ECM, Master cylinder solenoid (skid control ECU), Main body ECU (multiplex network body ECU)
      The drive monitor calculations stop and the display is blank. Nothing U0100
      U0129
      Eco Navigation Display
      (Displays the fuel consumption in 1 minute intervals and the average fuel consumption history.)
      1. Navigation receiver assembly
      2. ECM, Master cylinder solenoid (skid control ECU), Combination meter ECU assembly
      Stops updating the eco navigation display. Nothing U0155
      Entry Functions
      (Operates the entry lock/unlock, entry trunk open/entry back door unlatch and entry warning/illumination functions.)
      1. Certification ECU, Main body ECU (multiplex network body ECU)
      2. Main body ECU (multiplex network body ECU), Combination meter assembly
      The entry functions do not operate. Nothing U0142
      Wireless Functions
      (Operates the wireless lock/unlock, trunk and panic functions.)
      1. Main body ECU (multiplex network body ECU)
      2. Certification ECU
      The wireless functions do not operate. Nothing U0142
      Engine Switch Illumination Control
      (Turns the engine switch illumination on/off.)
      1. Certification ECU
      2. Main body ECU (multiplex network body ECU)
      The engine switch illumination does not operate. Nothing U0142
      Door Lock (Key-linked Function, Key Lock-in Prevention Function, etc.)
      (Performs lock/unlock control.)
      1. Main body ECU (multiplex network body ECU)
      2. ECM, Center airbag sensor assembly, Combination meter assembly
      The automatic lock operation is prohibited. Nothing U0100
      U0101
      U0151
      U0155
      Wireless/Entry and Start
      (Performs wireless/entry and start control.)
      1. Certification ECU
      2. Main body ECU (multiplex network body ECU)
      Entry and start/wireless control does not operate. Nothing U0327
      Alarm
      (Sounds warnings.)
      1. Main body ECU (multiplex network body ECU)
      2. ECM, Power management control ECU
      - Nothing U0100
      U0101
      U1133
      Lighting Control
      (Performs DRL control.)
      1. Main body ECU (multiplex network body ECU)
      2. ECM
      DRL control does not operate. Nothing U0100
      U0101
      Display Automatic Dimming
      (Controls display dimming control.)
      1. Combination meter assembly
      2. -
      Dims the interior display/indicators when not in the tail cancel state. Nothing U0155
      Illumination
      (Performs illumination control.)
      1. Combination meter assembly
      2. Certification ECU
      Turns off the map light. Nothing U0327
      ADD Switching Limitation
      (Prohibits the ADD actuator switching from free to lock when the difference between the vehicle wheel speeds is outside the acceptable range.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU)
      ADD switching is prohibited. The 4WD indicator light blinks and the buzzer sounds. -
      Rear Differential Lock Switching Limitation
      (Prohibits rear differential lock switching when the vehicle speed is outside the acceptable range.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU)
      Rear differential lock switching is prohibited. The 4WD indicator light blinks. -
      Specialized Control during Wheel Speed Failure
      (When there is abnormal wheel speed, this control permits switching only when specified conditions are met [not all wheel speeds are abnormal, the brakes are applied, the engine speed is low and all normal wheels speeds are low].)
      1. Four wheel drive control ECU
      2. ECM, Master cylinder solenoid (skid control ECU)
      When all 4 wheels are malfunctioning, switching is prohibited. The 4WD indicator light blinks. -
      4WD Indicator Light and Buzzer Signal Output
      (Outputs a signal indicating the indicator and buzzer state, which are used to determine the actuator position and switching status.)
      1. Four wheel drive control ECU
      2. Combination meter assembly
      State signal update is not possible. Nothing -
      4WD State Signal Output
      (Outputs a signal when switching to the H4 position is finished.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU), Combination meter assembly
      State signal update is not possible. The 4WD indicator light status changes in accordance with changes in the 4WD state signal. -
      L4 State Signal Output
      (Outputs a signal when switching to the L4 position is finished.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU), Combination meter assembly
      State signal update is not possible. The 4LO indicator light status changes in accordance with changes in the L4 state signal. -
      Rear Differential Lock State Signal Output
      (Outputs the rear differential P/S state.)
      1. Four wheel drive control ECU
      2. Combination meter assembly
      State signal update is not possible. The rear differential lock indicator light status changes in accordance with changes in the rear differential lock state signal. -
      Signal Output during Switching
      (Outputs the actuator switching state.)
      1. Four wheel drive control ECU
      2. Combination meter assembly
      State signal update is not possible. The indicator lights blink during signal output during switching. -
      Multi-terrain Select Output
      (Outputs an multi-terrain select service cancel command signal.)
      1. Four wheel drive control ECU
      2. Drive monitor switch
      State signal update is not possible. Nothing -
      High-Low Switching Limitation
      (Prohibits High-Low switching when the vehicle speed or engine speed is outside the acceptable range or the A/T is not in N during the A/T status check.)
      1. Four wheel drive control ECU
      2. ECM, Master cylinder solenoid (skid control ECU)
      High-Low switching is prohibited. The 4WD indicator light blinks and the buzzer sounds. -
      Center Differential Lock Switching Limitation
      (Prohibits center differential lock switching when the difference in wheel speeds is large.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU)
      Prohibits center differential lock switching. The 4WD indicator light blinks and the buzzer sounds. -
      L4F Switching Limitation
      (Prohibits switching to L4F when VSC is malfunctioning.)
      1. Four wheel drive control ECU
      2. Master cylinder solenoid (skid control ECU)
      L4F switching is prohibited. Nothing -
      H-L Actuator Failure Signal Output
      (Outputs a signal when the H-L actuator switch is malfunctioning.)
      1. Four wheel drive control ECU
      2. ECM, Master cylinder solenoid (skid control ECU), Combination meter assembly
      State signal update is not possible. The indicator lights blink quickly. -
      Cruise Control Cancel Signal Output
      (Outputs a cruise control cancel signal when center differential switching is not completed even though 5 seconds or more have elapsed from the start of switching.)
      1. Four wheel drive control ECU
      2. ECM
      State signal update is not possible. Nothing -
      Center Differential Lock State Signal Output
      (Outputs the center differential lock P/S state.)
      1. Four wheel drive control ECU
      2. Combination meter assembly
      State signal update is not possible. The status of the indicator lights change in accordance with changes in the center differential lock state signal. -
      Push Start (Power Source Switching)
      (Changes the power source mode automatically based on the push start switch signal and commands the starter to operate when certain conditions are met.)
      1. Power management control ECU
      2. ECM, Combination meter assembly, Main body ECU (multiplex network body ECU)
      Does not display the necessary starting operation commands. Nothing U0100
      KDSS System
      (Opens and closes the accumulator valve to suppress roll.)
      1. Stabilizer control ECU
      2. ECM, Master cylinder solenoid (skid control ECU), Yaw rate sensor assembly, Spiral cable sub-assembly (steering angle sensor)
      • Control continues.
      • The accumulator valve is open.
      Nothing U0100
      U0122
      U0124
      U0126
      Multi-function Switch
      (Operates the clearance sonar and 2nd start switch using the steering switch.)
      1. Drive monitor switch
      2. Combination meter assembly
      - Nothing -
      Multi-terrain Select
      (Informs the user of the recommended vehicle state according to driving conditions.)
      1. Drive monitor switch
      2. ECM, Master cylinder solenoid (skid control ECU), Combination meter assembly, Four wheel drive control ECU
      • Mode switching is not possible.
      • The display of text messages in the meter display is not possible.
      Nothing -
      Crawl Control Switch
      (Sends the crawl control switch information.)
      1. Drive monitor switch
      2. Master cylinder solenoid (skid control ECU)
      - Nothing -