LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Corolla LE, 1.8 L >> Repair and Diagnosis >> Engine Mechanical >> Engine Fuel System (2ZR-FE) >> Fuel Injector >> Installation

Fuel Injector: Installation

  1. INSTALL FUEL INJECTOR ASSEMBLY 
    1. Install 4 new injector vibration insulators to the 4 fuel injector assemblies.
    2. Install 4 new injector vibration insulators to the 4 fuel injector assemblies.
    3. Apply a light coat of gasoline or spindle oil to the contact surfaces of the O-rings of the fuel injector assemblies.
      Fig 1: Identifying Injector Vibration Insulators With O-Ring
      G06009875Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. While turning the fuel injector assembly left and right, install it onto the fuel delivery pipe sub-assembly.
      NOTE:
      • Do not twist the O-ring.
      • After installing the fuel injectors, check that they turn smoothly.
      Fig 2: Turning Fuel Injector Assembly Left And Right
      G06009876Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL NO. 1 DELIVERY PIPE SPACER 
    1. Install the 2 No. 1 delivery pipe spacers onto the cylinder head.
      NOTE: Install the No. 1 delivery pipe spacers in the correct direction.
    Fig 3: Identifying No. 1 Delivery Pipe Spacer
    G06009866Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY 
    1. Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies, then temporarily install the 2 bolts.
      NOTE:
      • Do not drop the fuel injectors when installing the fuel delivery pipe sub-assembly.
      • Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.
      Fig 4: Locating Fuel Delivery Pipe Sub-Assembly Bolts
      G06009864Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Tighten the 2 bolts to the specified torque.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

      Fig 5: Locating Fuel Delivery Pipe Sub-Assembly Bolts
      G06009864Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install the bolt to secure the fuel delivery pipe sub-assembly.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

      Fig 6: Locating Fuel Delivery Pipe Sub-Assembly
      G06009865Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the wire harness bracket with the bolt.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      Fig 7: Locating Wire Harness Bracket With Bolt
      G06009863Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. CONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Insert the fuel tube sub-assembly connector into the fuel delivery pipe until a "click" sound can be heard.
      NOTE:
      • Check that there are no scratches or foreign matter around the contact surfaces of the fuel tube connector and pipe before performing this work.
      • After connecting the fuel tube, check that the fuel tube connector and pipe are securely connected by pulling on them.
      Fig 8: Identifying Retainer, Pipe And O-Ring
      G06009882Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install a new No. 2 fuel pipe clamp (Type B).
      Fig 9: Locating No. 2 Fuel Pipe Clamp (Type B)
      G06009861Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Install a new No. 2 fuel pump clamp (Type A).
      Fig 10: Locating No. 2 Fuel Pump Clamp (Type A)
      G06009860Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. CONNECT ENGINE WIRE 
    1. Install the 2 wire harness brackets with the 2 bolts.

      Torque: 13 N*m (133 kgf*cm, 10 ft.*lbf) 

      Fig 11: Locating Wire Harness Brackets With Bolts
      G06009885Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the 4 wire harness clamps.
      Fig 12: Locating Wire Harness Clamps
      G06009858Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Connect the 4 fuel injector assembly connectors.
    4. Connect the 2 wire harness clamps.
    5. Connect the ground wires with the 2 bolts.
      Fig 13: Locating Fuel Injector Assembly Connectors
      G06009857Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL AIR CLEANER CAP SUB-ASSEMBLY  (See INSPECTION )
  7. CONNECT NO. 2 VENTILATION HOSE 
    1. Connect the No. 2 ventilation hose.
      Fig 14: Locating No. 2 Ventilation Hose
      G06009856Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    1. Connect the cable to the negative battery terminal.

    Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  9. INSPECT FOR FUEL LEAK  (See ON-VEHICLE INSPECTION )
  10. INSTALL NO. 2 CYLINDER HEAD COVER  (See INSTALLATION )