LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Corolla LE, 1.8 L >> Repair and Diagnosis >> Electrical >> Charging Systems >> Charging System (2ZR-FE) >> Generator >> Reassembly

Charging System (2ZR-FE): Generator: Reassembly

  1. INSTALL GENERATOR DRIVE END FRAME BEARING 
    1. Using SST and a press, press in a new generator drive end frame bearing.

      SST 09950-60010 (09951-00470), 09950-70010 (09951-07100) 

      Fig 1: Pressing Generator Drive End Frame Bearing
      G05399870Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fit the tabs of the retainer plate into the cutouts on the drive end frame to install the retainer plate.
    3. Install the 4 screws.

      Torque: 2.3 N*m (23 kgf*cm, 20 in.*lbf) 

  2. INSTALL GENERATOR ROTOR ASSEMBLY 
    1. Place the drive end frame on the clutch pulley.
      Fig 2: Fitting Tabs Of Retainer Plate Into Cutouts On Drive End Frame
      G05399871Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the generator rotor assembly to the drive end frame.
      Fig 3: Locating Generator Rotor Assembly
      G05399860Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Place the generator washer on the generator rotor.
      Fig 4: Identifying Generator Washer
      G05287973Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL GENERATOR COIL ASSEMBLY 
    1. Using SST and a press, slowly press in the generator coil assembly.

      SST 09612-70100 (09612-07240) 

      Fig 5: Pressing Generator Coil Assembly
      G05399874Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the 4 bolts.

      Torque: 5.8 N*m (59 kgf*cm, 51 in.*lbf) 

      Fig 6: Locating Generator Coil Assembly Bolts
      G05399857Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY 
    1. While pushing the 2 brushes into the generator brush holder assembly, insert a 01.0 mm (0.0394 in.) pin into the brush holder hole.
      Fig 7: Inserting Pin Into Brush Holder Hole
      G06010896Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the brush holder assembly to the generator coil with the 2 screws.

      Torque: 1.8 N*m (18 kgf*cm, 16 in.*lbf) 

      Fig 8: Locating Generator Coil Screws
      G05399877Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pull out the pin from the generator brush holder.
      Fig 9: Pulling Out Pin From Generator Brush Holder
      G05399878Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL GENERATOR TERMINAL INSULATOR 
    1. Install the terminal insulator to the generator coil.
      NOTE: Pay attention to the installation direction of the terminal insulator as shown in the illustration.
      Fig 10: Locating Generator Terminal Insulator
      G05399879Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. INSTALL GENERATOR REAR END COVER 
    1. Install the generator rear end cover to the generator coil with the 3 nuts.

      Torque: 4.6 N*m (47 kgf*cm, 41 in.*lbf) 

  7. INSTALL GENERATOR CLUTCH PULLEY 
    1. Temporarily install the clutch pulley onto the rotor shaft.
      Fig 11: Locating Generator Rear End Cover Nuts
      G05399854Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Set SST (A) and (B).

      SST 09820-63021 

      Fig 12: Installing SST (A) Into SST (B)
      G04975758Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Clamp SST (A) in a vise.
    4. Place the rotor shaft end into SST (A).
      Fig 13: Placing Rotor Shaft End Into SST
      G05399850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Fit SST (B) to the clutch pulley.
      Fig 14: Fitting SST To Clutch Pulley
      G05399851Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Tighten the pulley by turning SST (B) in the direction shown in the illustration.

      Torque: without SST 

      111 N*m (1127 kgf*cm, 82 ft.*lbf) 

      with SST 

      84 N*m (857 kgf*cm, 62 ft.*lbf) 

      NOTE:
      • Use a torque wrench with a fulcrum length of 318 mm (12.52 in.).
      • This torque value is effective when SST is parallel to the torque wrench.
    7. Remove the generator assembly from SST.
    8. Check that the clutch pulley rotates smoothly.
    9. Install a new clutch pulley cap to the clutch pulley.
      Fig 15: Tightening Pulley
      G05399884Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002