Terminals Of Ecu
WARNING: This page is about a different car, the 2009 Lexus IS F. However, it is still accessible from the selected car via links, so may be relevant.
- CHECK BATTERY VOLTAGE
- Check the battery voltage.
Standard Voltage
11 to 14 V
- Check the battery voltage.
- SKID CONTROL ECU INSPECTION
- Measure the voltage between each terminal or between each terminal and the body ground.
- Connect the Techstream to the DLC3, and check the communication condition with the skid control ECU.
- Using an oscilloscope, check the pulse generated between each terminal or between each terminal and body ground.NOTE:
Inspection should be performed from the back of the connector with the connector connected to the skid control ECU.
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition A35-1 (SFRR) - Body ground GR - Body ground Front decrease solenoid RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V A35-2 (SRLR) - Body ground R - Body ground Rear decrease solenoid LH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V A35-3 (MR) - Body ground L-B - Body ground ABS motor relay output Engine switch on (IG) 11 to 14 V A35-4 (FLO) - Body ground R-L - Body ground Front wheel speed signal LH output While driving Pulse generation
(see waveform 1 in Fig 2)A35-5 (FRO) - Body ground G-W - Body ground Front wheel speed signal RH output While driving Pulse generation
(see waveform 1 in Fig 2)A35-7 (FR-) - Body ground G - Body ground Front wheel speed sensor RH input Vehicle speed (forward or backward) input Pulse generation
(see waveform 2 in Fig 3)A35-8 (FR+) - Body ground L - Body ground Front wheel speed sensor power supply RH output Engine switch on (IG) 11 to 14 V A35-9 (FL+) - Body ground P - Body ground Front wheel speed sensor power supply LH output Engine switch on (IG) 11 to 14 V A35-10 (FL-) - Body ground L - Body ground Front wheel speed sensor LH input Vehicle speed (forward or backward) input Pulse generation
(see waveform 2 in Fig 3)A35-11 (R+) - Body ground G - Body ground ABS solenoid relay power supply Engine switch on (IG) 11 to 14 V A35-12 (SRRR) - Body ground W-L - Body ground Rear decrease solenoid RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V A35-13 (SFLR) - Body ground W - Body ground Front decrease solenoid RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V A35-14 (SSEL) - Body ground Y-B - Body ground Solenoid characteristic identification input 1 Engine start Low: 0 V (Normal)
Middle: 3.7 to 8.26 V
High: 7.8 to 14 VA35-16 (SEL2) - Body ground B-L - Body ground Solenoid characteristic identification input 2 Engine start Low: 0 V (Normal)
Middle: 3.7 to 8.26 V
High: 7.8 to 14 VA35-18 (FSW+) - Body ground G-B - Body ground Brake pedal load sensing switch input Stop light switch OFF → ON (Brake pedal depressed → released) 950 to 1050 Ω →
203 to 223 ΩA35-20 (STP2) - Body ground R-B - Body ground Stop light control (BRK-LP) relay input Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V →
Below 1.5 VA35-21 (STPO) - Body ground L - Body ground Stop light control (BRK-LP) relay output Engine switch on (IG) 11 to 14 V A35-22 (GND3) - Body ground W-B - Body ground Skid control ECU ground 3 Always Below 1 Ω J77-1 (IG1) - Body ground B - Body ground IG1 power supply Engine switch on (IG) 11 to 14 V J77-3 (RL-) - Body ground B - Body ground Rear wheel speed sensor LH input Vehicle speed (forward or backward) input Pulse generation
(see waveform 2 in Fig 3)J77-4 (RL+) - Body ground LG - Body ground Rear wheel speed sensor power supply LH output Engine switch on (IG) 11 to 14 V J77-5 (RR+) - Body ground B - Body ground Rear wheel speed sensor power supply RH output Engine switch on (IG) 11 to 14 V J77-6 (RR-) - Body ground G - Body ground Rear wheel speed sensor RH input Vehicle speed (forward or backward) input Pulse generation
(see waveform 2 in Fig 3)J77-7 (CSW) - Body ground P - Body ground VSC OFF switch input VSC OFF switch ON → OFF Below 1 Ω →
10 kΩ or higherJ77-8 (CANH) - Body ground R - Body ground CAN communication line H Engine switch off 54 to 67 Ω J77-9 (SP1) - Body ground V - Body ground Speed signal output for combination meter While driving Pulse generation
(see waveform 3 in Fig 4)J77-10 (STP1) - Body ground R - Body ground Stop light switch input Stop light switch ON → OFF (Brake pedal depressed → released) 11 to 14 V →
Below 1.5 VJ77-11 (BZ) - Body ground L - Body ground Skid control buzzer output Engine switch on (IG), buzzer sound → not sound Below 1 V →
11 to 14 VJ77-12 (D/G) - Body ground R - Body ground Diagnosis tester communication line Engine switch on (IG) 11 to 14 V J77-13 (TS) - Body ground SB - Body ground Sensor check activation input Engine switch on (IG), terminals TS and CG of DLC3 connect → disconnect Below 1.5 V →
11 to 14 VJ77-14 (PKB) - Body ground Y - Body ground Parking brake switch input Engine switch on (IG), parking brake switch ON → OFF Below 1 Ω →
10 kΩ or higherJ77-15 (WFSE) - Body ground GR - Body ground ECU program rewrite input - - J77-16 (CANL) - Body ground W - Body ground CAN communication line L Engine switch off 54 to 67 Ω J78-1 (MRF) - Body ground Y - Body ground ABS motor fail safe relay output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-2 (SR) - Body ground V - Body ground ABS solenoid relay output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-4 (PMC) - Body ground R - Body ground Master cylinder pressure sensor input Engine switch on (IG), brake pedal released 0.3 to 0.8 V J78-6 (E2) - Body ground W - Body ground Master cylinder pressure sensor ground Always Below 1 Ω J78-7 (RRA+) - Body ground L - Body ground Rear holding solenoid (+) RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-8 (FLA-) - Body ground W - Body ground Front holding solenoid (-) LH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-9 (RLA+) - Body ground G - Body ground Rear holding solenoid (+) LH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-10 (FRA-) - Body ground GR - Body ground Front holding solenoid (-) RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-11 (SM2+) - Body ground B - Body ground Master cut linear solenoid 2 (+) output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-12 (SM1-) - Body ground R - Body ground Master cut linear solenoid 1 (-) output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-13 (AST) - Body ground Y - Body ground Linear solenoid power supply Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-14 (GND2) - Body ground W-B - Body ground Skid control ECU ground 2 Always Below 1 Ω J78-15 (MT) - Body ground GR - Body ground ABS motor relay test input Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-18 (VCM) - Body ground B - Body ground Master cylinder pressure sensor power supply output Engine switch on (IG) 4.5 to 5.5 V J78-19 (FSS) - Body ground Shielded - Body ground Master cylinder pressure sensor shielded ground Always Below 1 Ω J78-20 (RRA-) - Body ground BE - Body ground Rear holding solenoid (-) RH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-21 (FLA+) - Body ground V - Body ground Front holding solenoid (+) LH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-22 (RLA-) - Body ground P - Body ground Rear holding solenoid (-) LH output Approx. 1.5 seconds after turning engine switch on (IG) 11 to 14 V J78-23 (FRA+) - Body ground LG - Body ground Front holding solenoid (+) RH output Approx. 1.5 seconds after turning engine switch on (IG 11 to 14 V J78-24 (SM2-) - Body ground BR - Body ground Master cut linear solenoid 2 (-) output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-25 (SM1+) - Body ground SB - Body ground Master cut linear solenoid 1 (+) output Approx. 1.5 seconds after turning engine switch on (IG) Below 1 V J78-26 (GND1) - Body ground W-B - Body ground Skid control ECU ground 1 Always Below 1 Ω - Waveform 1 (Reference): Using an oscilloscope:
Item Condition Tool setting 5 V/DIV., 5 ms./DIV. Vehicle condition While driving at approximately 20 km/h (12 mph) HINT:
As the vehicle speed (wheel speed) becomes faster, the cycle becomes shorter.
- Waveform 2 (Reference): Using an oscilloscope:
Item Condition Tool setting 0.5 V/DIV., 2 ms./DIV. Vehicle condition Moving forward or backward HINT:
As the vehicle speed (wheel speed) becomes faster, the cycle becomes shorter.
- Waveform 3 (Reference): Using an oscilloscope:
Item Condition Tool setting 5 V/DIV., 50 ms./DIV. Vehicle condition While driving at approximately 20 km/h (12 mph) HINT:
As the vehicle speed (wheel speed) becomes faster, the cycle becomes shorter.