LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2007 >> RAV4 Base, 3.5 K, AWD >> Repair and Diagnosis >> Electrical >> Charging Systems >> Charging System (2GR-FE) >> Generator >> Reassembly

Charging System (2GR-FE): Generator: Reassembly

  1. INSTALL GENERATOR ROTOR ASSEMBLY 
    1. Install the washer onto the generator rectifier end frame.
      Fig 1: Installing Washer Onto Generator Rectifier End Frame
      G04486201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the generator rotor onto the generator rectifier end frame.
      Fig 2: Installing Generator Rotor Onto Generator Rectifier End Frame
      G04486202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Using a 21 mm deep socket wrench and press, slowly push the generator drive end frame onto the generator rectifier frame.
      Fig 3: Pushing Generator Drive End Frame Onto Generator Rectifier Frame
      G04486203Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the 4 bolts.

      Torque: 5.8 N*m (59 kgf*cm, 51 in.*lbf) 

      Fig 4: Installing Generator Case Bolts
      G04486204Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY 
    1. While pushing the 2 brushes into the generator brush holder, insert a 1.0 mm (0.039 in.) diameter pin into the generator brush holder.
      Fig 5: Inserting A 1.0 mm (0.039 in.) Diameter Pin Into Generator Brush Holder
      G04486205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the generator brush holder with the 2 screws.

      Torque: 1.8 N*m (18 kgf*cm, 16 in.*lbf) 

      Fig 6: Installing Generator Brush Holder
      G04486206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Pull the pin out of the generator brush holder.
    4. Install the terminal insulator onto the generator rectifier end frame.
      Fig 7: Installing Terminal Insulator
      G04486207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Install the generator rear end cover with the 3 nuts.

      Torque: 4.6 N*m (47 kgf*cm, 41 in.*lbf) 

      Fig 8: Installing Generator Rear End Cover
      G04486208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Install the bracket with the bolt.

      Torque: 20 N*m (204 kgf*cm, 15 ft.*lbf) 

      Fig 9: Installing Bracket
      G04486209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Install the wire harness clamp stay.

      Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf) 

      Fig 10: Installing Wire Harness Clamp Stay
      G04486210Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL GENERATOR PULLEY WITH CLUTCH 
    1. Install the pulley by hand.
    2. Install SST to the pulley as shown.

      SST 09820-63020 

      Fig 11: Installing Sst To Pulley
      G04486211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Turn SST (B) counterclockwise to tighten the pulley.

      Torque: 111 N*m (1125 kgf*cm, 81 ft.*lbf) 

      Fig 12: Turning SST (B) Counterclockwise To Tighten Pulley
      G04486212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install a new cap to the pulley.
    5. Check that the generator pulley rotates smoothly.