LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2006 >> Sienna LE, AWD >> Repair and Diagnosis >> Engine Performance >> Fuel Delivery >> Engine Fuel System (3MZ-FE) >> Fuel Tank >> Removal

Fuel Tank: Removal

  1. DISCHARGE FUEL SYSTEM PRESSURE (See  PRECAUTION   ) 
  2. REMOVE CHARCOAL CANISTER PROTECTOR (See  REMOVAL  ) 
  3. REMOVE FUEL TANK FILLER HOSE COVER 
    1. Remove the 3 bolts and the fuel tank filler hose cover.
      Fig 1: Removing Fuel Tank Filler Hose Cover
      G04494391Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE FUEL TANK ASSEMBLY 
    1. Disconnect the fuel tank vent hose.
      1. Deeply push the connector to release the locking tab.
      2. Pinch portion A.
      3. Pull out the connector.
        Fig 2: Disconnecting Fuel Tank Vent Hose
        G04494392Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the fuel tank main tube.
      1. Pinch the tube connector and then pull out the fuel tank main tube.
        Fig 3: Pinching Tube Connector And Pulling Out Fuel Tank Main Tube
        G04494393Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        NOTE:
        • Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary.
        • Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.
        • Do not use any tool in this operation.
        • Do not bend or twist the nylon tube.

          Protect the connector by covering it with a vinyl or plastic bag.

        • When the pipe and the connector are stuck, push and pull the connector to release and pull the connector out carefully.
        Fig 4: Pushing And Pulling Connector To Release
        G04494394Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the fuel tank to filler pipe hose.
      1. Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.
        Fig 5: Disconnecting Fuel Tank To Filler Pipe Hose
        G04494395Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect the fuel tube.
      1. Pinch the tube connector and then pull out the fuel tank main tube.
        NOTE:
        • Check if there is any dirt or mud around the connector before this operation and remove the dirt as necessary.
        • Be careful of mud because the quick connector has an O-ring which seals the pipe and connector that can be contaminated.
        • Do not use any tool in this operation.
        • Do not bend or twist the nylon tube.

          Protect the connector by covering it with a vinyl or plastic bag.

        • When the pipe and the connector are stuck, push and pull the connector to release and pull the connector out carefully.
        Fig 6: Disconnecting Fuel Tube
        G04494396Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the 2 wire harness clamps.
      Fig 7: Removing Wire Harness Clamps
      G04494397Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Set up a transmission jack under the fuel tank.
    7. Remove the 6 set bolts of the 3 fuel tank bands.
      Fig 8: Removing Fuel Tank Bands
      G04494398Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. While operating the transmission jack, unfasten the 4 claws for the wire harness and disconnect the fuel pump connector and vapor pressure sensor connector, then remove the fuel tank and the 3 fuel tank bands from the vehicle.
      Fig 9: Disconnecting Fuel Pump Connector And Vapor Pressure Sensor Connector
      G04494399Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002