LEMON Manuals: Even more car manuals for everyone

Inspection Procedure

  1. Check fuse (PWR SEAT). 

    PREPARATION: 

    Remove the PWR SEAT fuse from the Instrument Panel J/B.

    CHECK: 

    Measure the resistance.

    OK: 

    Below 1 Ω 

    1. NG: Replace fuse. 
    2. OK: Go to next step. 
  2. Inspect Lumbar Support Control Switch. 

    PREPARATION: 

    Disconnect the Lumbar Support Control Switch Connector.

    CHECK: 

    Measure the resistance of each terminal, as shown in the illustration and table.

    OK: 

    TESTER CONNECTION SPECIFIED CONDITION CHART

    Tester Connection Switch Position Specified Condition
    1 - 2 HOLD (Front) Below 1 Ω
    3 - 4 HOLD (Front) Below 1 Ω
    1 - 2 OFF Below 1 Ω
    4 - 5 OFF Below 1 Ω
    1 - 3 RELEASE (Rear) Below 1 Ω
    4 - 5 RELEASE (Rear) Below 1 Ω
    Fig 1: Identifying Lumbar Support Control Switch Connector
    G03059700Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: Replace Lumbar Support Control Switch assy (See  DISASSEMBLY  ). 
    2. OK: Go to next step. 
  3. Check Harness and Connector (Power Source). 

    CHECK: 

    Measure the voltage of each terminal of the Wire Harness Side Connectors.

    OK: 

    TESTER CONNECTION SPECIFIED CONDITION CHART

    Tester Connection Condition Specified Condition
    L4-3 - Body Ground Always 10 to 14 V

    CHECK: 

    Measure the resistance of each terminal, as shown in the illustration and table.

    Fig 2: Identifying L4 Lumbar Support Control Switch Connector
    G03059701Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: 

    TESTER CONNECTION SPECIFIED CONDITION CHART

    Tester Connection Condition Specified Condition
    L4-2 - Body Ground Always Below 1 Ω
    L4-5 - Body Ground Always Below 1 Ω
    1. NG: Repair or replace Harness or Connector. 
    2. OK: Go to next step. 
  4. Inspect Lumbar Support Control Motor. 

    PREPARATION: 

    Remove the Lumbar Support Control Motor (See DISASSEMBLY ).

    CHECK: 

    Check that the motor rotates smoothly when the battery is connected to the Lumbar Support Control Motor Connector Terminals.

    OK: 

    DIAGNOSIS PROCEDURE

    Measurement Condition Operational Direction
    Battery Positive (+) --> 1 Battery Negative (-)--> 2 Clockwise
    Battery Positive (+) --> 2 Battery Negative (-) --> 1 Counterclockwise
    Fig 3: Identifying Lumbar Support Control Motor L3 Connector
    G03059702Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: Replace Lumbar Support Control Motor (See  DISASSEMBLY  ). 
    2. OK: Go to next step. 
  5. Check Harness and Connector (Lumbar Support Control Switch - Lumbar Support Control Motor). 

    CHECK: 

    Measure the resistance of each terminal, as shown in the illustration and table.

    OK: 

    TESTER CONNECTION SPECIFIED CONDITION CHART

    Tester Connection Condition Specified Condition
    L4-1 - L3-2 Always Below 1 Ω
    L4-4 - L3-1 Always Below 1 Ω
    L4-1 - Body ground Always 10 k Ω or higher
    L4-4 - Body ground Always 10 k Ω or higher
    Fig 4: Identifying L4 Lumbar Support Control Switch Connector
    G03059703Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    Fig 5: Identifying Lumbar Support Control Motor L3 Connector
    G03059704Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: Repair or replace Harness or Connector. 
    2. OK: Proceed to next Circuit Inspection shown in Problem Symptoms Table (See  PROBLEM SYMPTOMS TABLE  ).