LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2004 >> Sequoia SR5, RWD >> Repair and Diagnosis >> Body & Frame >> Windows >> Rear Door >> Disassembly

Rear Door: Disassembly

  1. REMOVE INSIDE HANDLE BEZEL 
    1. Using a screwdriver, open the cover.

      Tape the screwdriver tip before use.

    2. Remove the screw.
    3. Using a screwdriver, remove the inside handle bezel as shown in the illustration.
    NOTE: Tape the screwdriver tip before use.
  2. REMOVE COURTESY LIGHT 
  3. REMOVE UPPER ARMREST BASE PANEL WITH POWER WINDOW SWITCH 
    1. Remove the ash tray.
      Fig 1: Removing Inside Handle Bezel
      G02928243Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Using a screwdriver, remove the upper armrest base panel with power window switch.
      Fig 2: Removing Upper Armrest Base Panel With Power Window Switch
      G02928244Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Disconnect the connector.
    4. Remove the power window switch from the upper armrest base panel.
  4. REMOVE DOOR TRIM 
    1. Using a screwdriver, remove the cap.
      NOTE: Tape the screwdriver tip before use.
    2. Remove the screw and 2 clips.
    3. Insert a screwdriver between the door trim and door panel to pry the door trim.
      NOTE: Tape the screwdriver tip before use.
    4. Pull the door trim upward to remove the door trim.
      Fig 3: Removing Door Trim
      G02928245Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the inner weatherstrip from the door trim.
  5. REMOVE SPEAKER 
  6. REMOVE INSIDE HANDLE 
    1. Slide the inside handle backward to remove it.
      Fig 4: Removing Inside Handle Backward
      G02928246Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the 2 cables from inside handle as shown in the illustration.
      Fig 5: Disconnecting Cable's From Inside Handle
      G02928247Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE SERVICE HOLE COVER 
    1. Using a clip remover, remove the clamp and grommets.
    2. Remove the service hole cover.
    NOTE: Do not tear the cover.
    NOTE: At the time of reassembly, please refer to the following item. Bring out the 2 control cables and wire harness through the service hole cover.
  8. REMOVE DIVISION BAR 
    NOTE: Insert a shop rag inside the door panel to prevent scratching the glass.
    1. Open the door glass until the bolts appear in the service hole.
    2. Remove the 2 door glass set nuts.
    3. Remove the door glass from the glass bracket and lower the door glass into the door panel.
      NOTE: Do not damage the door glass.
      NOTE: Position the door glass toward the front as much as possible.
    4. Remove the door glass run.
    5. Remove the 2 bolts and screw.
    6. Pull the division bar forward.
      Fig 6: Removing Bolts Screw From Rear Door
      G02928248Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Rotate the division bar 90° and pull it upward as shown in the illustration.
  9. REMOVE REAR DOOR QUARTER WINDOW GLASS 
    1. Remove the rear door quarter window glass.
      NOTE: Do not damage the glass.
    2. Remove the quarter window weatherstrip from the glass.
  10. REMOVE DOOR GLASS 

    Pull the glass up out of the panel carefully.

    NOTE: Insert a shop rag inside the panel to prevent scratching the glass.
    Fig 7: Rotating Division Bar
    G02928249Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE UPPER WINDOW FRAME MOULDING 
    1. Remove the 5 screws.
    2. Using a screwdriver or clip remover, remove the upper window frame moulding.
      Fig 8: Removing Upper Window From Moulding
      G02928250Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE: Tape the screwdriver tip before use.
  12. REMOVE DOOR BELT MOULDING 
    1. Apply protective tape to the outer surface as shown in the illustration, to keep the surface from being scratched.
    2. Using a moulding remover, remove the door belt moulding.
    Fig 9: Locating Door Belt Moulding Clips
    G02928251Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE WINDOW REGULATOR ASSEMBLY 
    1. Disconnect the connector.
    2. Remove the 3 bolts.
      1. Torque: 8.0 N.m (82 kgf°Cm, 71 in..lbf) 
    3. Loosen the bolt, then remove the window regulator assembly.
      1. Torque: 8.0 N.m (82 kgf°Cm, 71 in..lbf) 
      NOTE: Remove the window regulator assembly through the service hole.
      Fig 10: Removing Window Regulator Assembly
      G02928252Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 3 screws and window regulator motor from the window regulator sub-assembly.
      Fig 11: Removing Screw And Window Regulator Motor From Regulator Subassembly
      G02928253Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE: At the time of reassembly, please refer to the following items.
    • Tighten the bolts in the order shown in the illustration.
    • Apply MP grease to the window regulator assembly.
      Fig 12: Applying MP Grease Window Regulator Assembly
      G02928254Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    NOTE: At the time of reassembly, please refer to the following item.

    Do not apply grease to the spring of the window regulator assembly.

  14. REMOVE DOOR LOCK 
    1. Disengage the 2 control cables from the clamp.
    2. Remove the clamp.
    3. Remove the screw and cable protector.
      Fig 13: Removing Screw And Cable Protector
      G02928255Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect the connector.
    5. Remove the bolt, 3 screws and door lock.
      NOTE: Remove the door lock through the service hole.
      1. Torque: 
      2. Bolt: 5.0 N.m (51 kgf°Cm, 44 in..lbf) 
      3. Screw: 5.5 N.m (56 kgf°Cm, 49 in..lbf) 
      NOTE:
      • At the time of reassembly, please refer to the following items.
      • Apply adhesive to 3 screws.

        Part No. 08833-00070, THREE BOND 1324 or equivalent. 

      • Install the door lock as shown in the illustration.
        Fig 14: Removing Screw And Door Bolt
        G02928256Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Remove the 2 screws and door lock outer cover from the door lock.
    NOTE: At the time of reassembly, please refer to the following item. Apply MP grease to the sliding and rotating part of the door lock.
    Fig 15: Applying Grease Sliding Rotating Part Of Door Lock
    G02928257Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE OUTSIDE HANDLE 
    1. Torque: 5.5 N.m (56 kgf°Cm, 49 in..lbf) 
  16. REMOVE REAR DOOR WEATHERSTRIP 
  17. REMOVE REAR DOOR OUTSIDE LOWER MOULDING 
  18. REMOVE NO. 2 REAR DOOR WEATHERSTRIP