LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2004 >> Prius >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (SFI) - Diagnosis >> DTC P2A00: A/F Sensor Circuit Slow Response (Bank1 Sensor 1) >> Inspection Procedure

Inspection Procedure

HINT:

Malfunctioning areas can be found by performing the ACTIVE TEST / A/F CONTROL operation. The A/F CONTROL operation can determine if the A/F sensor, heated oxygen sensor or other potential trouble area are malfunctioning or not.

  1. Perform the ACTIVE TEST A/F CONTROL operation.

    HINT:

    The A/F CONTROL operation lowers the injection volume 12.5% or increases the injection volume 25%.

    1. Connect the hand-held tester to the DLC3 on the vehicle.
    2. Turn the power switch ON (IG).
    3. Put the engine in inspection mode (see INFORMATION ).
    4. Warm up the engine by running the engine at 2,500 RPM with the accelerator pedal depressed more than 60 % for approximately 90 seconds.
    5. Select the item: DIAGNOSIS / ENHANCED OBD II / ACTIVE TEST / A/F CONTROL.
    6. Perform the A/F CONTROL operation with the engine in an idle condition (press the right or left button).

Result: 

A/F sensor reacts in accordance with increase and decrease of injection volume: 

+25 % --> rich output: Less than 3.0 V 

-12.5 % --> lean output: More than 3.35 V 

Heated oxygen sensor reacts in accordance with increase and decrease of injection volume: 

+25 % --> rich output: More than 0.55 V 

-12.5 % --> lean output: Less than 0.4 V 

NOTE: The A/F sensor output has a few seconds of delay and the heated oxygen sensor output has about 20 seconds of delay at maximum.
Fig 1: Identifying Output A/F Sensor And Heated Oxygen Sensor
G02917364Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

The following A/F CONTROL procedure enables the technician to check and graph the voltage output of both A/F sensor and heated oxygen sensor.

To display the graph, enter ACTIVE TEST / A/F CONTROL / USER DATA, select "AFS B1S1 and O2S B1S2" by pressing the "YES" button followed by the "ENTER" button and then the "F4" button.

  1. CHECK OTHER DTC OUTPUT IN ADDITION TO A/F SENSOR DTC) 
    1. Connect the hand-held tester or the OBD II scan tool to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the hand-held tester or the OBD II scan tool ON.
    4. On the hand-held tester, select the item: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
    5. Read DTCs using the hand-held tester or the OBD II scan tool.

    Result: 

    DTC Output Display

    Display (DTC Output) Proceed to
    P2A00 A
    P2A00 and other DTCs B

    HINT:

    If any other code besides P2A00 are output, perform troubleshooting for those DTCs first.

    B: GO TO RELEVANT DTC CHART (See Hand Held Tester Display Active Test Table. (2 Of 2)  Figure  ) 

  2. READ VALUE OF OBD II SCAN TOOL OR HAND-HELD TESTER (OUTPUT VOLTAGE OF A/F SENSOR) 
    1. Connect the hand-held tester or the OBD II scan tool to the DLC 3.
    2. Put the engine in inspection mode (see INFORMATION ).
    3. Warm up the A/F sensors (bank 1 sensor 1) by running the engine at 2,500 RPM, depressing the accelerator pedal more than 60 % for approximately 90 seconds.
    4. Read A/F sensor voltage output on the OBD II scan tool or the hand-held tester.
    5. Hand-held tester only:

      On the hand-held tester, enter the menus: ENHANCED OBD II / SNAPSHOT / MANUAL SNAPSHOT / USER DATA.

    6. Select "AFS B1 S1/ENGINE SPD" and press button "YES".
    7. Monitor the A/F sensor voltage carefully.
    8. Check the A/F sensor voltage output under the following conditions:
      1. Put the engine in inspection mode and allow the engine to idle for 30 seconds.
      2. Put the engine in inspection mode and running the engine at 2,500 RPM with the accelerator pedal depressed more than 60 % (where engine RPM is not suddenly changed).
      3. Deactivate the inspection mode and drive the vehicle with shift position "B" range.
      4. Accelerate the vehicle to 44 mph (70 km/h) and quickly release the accelerator pedal so that the throttle valve fully close.
    CAUTION:
    • Strictly observe of posted speed limits, traffic laws, and road conditions when performing these drive patterns.
    • Do not drive the vehicle without deactivating inspection mode, otherwise damaging the trans-axle may result.

    Standard: 

    Condition (1)and (2) 

    Voltage changes in the vicinity of 3.3 V (0.66 V)* (between approximately 3.1 to 3.5 V) as shown in the illustration. 

    Condition (4) 

    A/F sensor voltage increases to 3.8 V (0.76 V)* or more during engine deceleration (when fuel cut) as shown in the illustration. 

    *: Voltage when using the OBD II scan tool. 

    Fig 2: Normal And Malfunction Condition Comparison
    G02917365Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    • Whenever the output voltage of the A/F sensor remains at approximately 3.3 V (0.660 V)* (see diagram Malfunction Condition) under any condition as well as the above conditions, the A/F sensor may have an open-circuit. (This will happen also when the A/F sensor heater has an open-circuit.)
    • Whenever the output voltage of the A/F sensor remains at a certain value of approximately 3.8 V (0.76 V)* or more, or 2.8 V (0.56 V)* or less (see diagram Malfunction Condition) under any condition as well as the above conditions, the A/F sensor may have a short-circuit.
    • The ECM will stop fuel injection (fuel cut) during engine deceleration. This will cause a LEAN condition and should result in a momentary increase in A/F sensor voltage output.
    • The ECM must establish a closed throttle position learned value to perform fuel cut. If the battery terminal was reconnected, the vehicle must be driven over 10 mph (16 km/h) to allow the ECM to learn the closed throttle position.
    • When the vehicle is driven:

      The output voltage of the A/F sensor may be below 2.8 V (0.76 V)* during fuel enrichment. For the vehicle, this translates to a sudden increase in speeds with the accelerator pedal fully depressed when trying to overtake another vehicle. The A/F sensor is functioning normally.

    • The A/F sensor is a current output element, and therefore the current is converted into voltage inside the ECM. If measuring voltage at connectors of A/F sensor or ECM, you will observe a constant voltage.

    *: Voltage when using the OBD II scan tool.

    OK: Go to step   13 

    NG: Go To Next Step 

  3. INSPECT AIR FUEL RATIO SENSOR (RESISTANCE OF A/F SENSOR HEATER) 
    Fig 3: Identifying Air Fuel Sensor Connector Components Side
    G02917366Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the A5 A/F sensor connector.
    2. Measure the resistance between the terminals of the A/F sensor.

      Standard: 

      RESISTANCE MEASURING

      Tester Connection Resistance
      HT(1) -+B(2) 1.8 to 3.4 +/- at 20°C (68°F)
    3. Reconnect the A/F sensor connector.

    NG: REPLACE AIR FUEL RATIO SENSOR 

    OK: Go To Next Step 

  4. INSPECT INTEGRATION RELAY (EFI M RELAY) 
    Fig 4: Removing Integration Relay
    G02917367Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the integration relay from the engine room R/B.
    2. Inspect the EFI M relay.

      Standard: 

      RELAY RESISTANCE SPECIFICATION

      Tester Connection Specified Condition
      (3K-1) - (3I-8) 10 kΩ or higher
      (3K-1) - (3I-8) Below 1Ω (Apply battery voltage to terminals 3I-6 and 3I-7)
    3. Reinstall the integration relay.

    NG: REPLACE INTEGRATION RELAY 

    OK: Go To Next Step 

  5. CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) 
    1. Disconnect the A5 A/F sensor connector.
    2. Disconnect the E5 ECM connector.
    3. Check the resistance between the wire harness side connectors.
      Fig 5: Identifying A/F Sensor Connector
      G02917368Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 6: Disconnecting ECM Connector E5
      G02917369Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Standard (Check for open): 

      CONNECTOR RESISTANCE SPECIFICATION

      Tester Connection Specified Condition
      AF+ (A5-3) - A1A+ (E5-23) Below 1 Ω
      AF- (A5-4) - A1A- (E5-22) Below 1 Ω
      HT (A5-1) - HA1A (E5-7) Below 1 Ω

      Standard (Check for short): 

      CONNECTOR RESISTANCE

      Tester Connection Specified Condition
      AF+ (A5-3) or A1A+ (E5-23) - Body ground 10 kΩ or higher
      AF- (A5-4) or A1A- (E5-22) - Body ground 10 kΩ or higher
      HT (A5-1) or HA1A (E5-7) - Body ground 10 kΩ or higher
    4. Reconnect the A/F sensor connector.
    5. Reconnect the ECM connector.
    Fig 7: Bank 1 System 1 Diagram
    G02917370Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    NG: REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go To Next Step 

  6. CHECK AIR INDUCTION SYSTEM 
    1. Check for vacuum leaks in the air induction system.

    OK: There is no leakage in the air induction system. 

    NG: REPAIR OR REPLACE AIR INDUCTION SYSTEM 

    OK: Go To Next Step 

  7. CHECK CONNECTION OF PCV HOSE 

    OK: PCV hose is connected correctly and PCV hose has no damage. 

    NG: REPAIR OR REPLACE PCV HOSE 

    OK: Go To Next Step 

  8. CHECK FUEL PRESSURE (See  FUEL SYSTEM  ) 

    OK: 

    Fuel pressure: 304 to 343 kPa (3.1 to 3.5 kgf/cm 2  , 44 to 50 psi) 

    NG: REPAIR OR REPLACE FUEL SYSTEM 

    OK: Go To Next Step 

  9. INSPECT FUEL INJECTOR ASSY (See  FUEL SYSTEM  ) 
    1. Check the injector injection (high or low fuel injection quantity or poor injection pattern).

    OK: 

    Injection volume: 36 to 46 cm 3  (2.1 to 2.8 cu in.) per 15 seconds. 

    NG: REPLACE FUEL INJECTOR ASSY (See  FUEL SYSTEM  ) 

    OK: Go To Next Step 

    REPLACE AIR FUEL RATIO SENSOR 

    GO: Go To Next Step 

  10. PERFORM CONFIRMATION DRIVING PATTERN (See  WIRING DIAGRAM   ) 

    HINT:

    Clear all DTCs prior to performing the confirmation driving pattern (see WIRING DIAGRAM  ).

    GO: Go To Next Step 

  11. READ OUTPUT DTC (SEE IF A/F SENSOR DTC IS OUTPUT AGAIN) 
    1. Connect the hand-held tester or the OBD II scan tool to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the hand-held tester or the OBD II scan tool ON.
    4. On the hand-held tester, select the item: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
    5. Read DTCs using the hand-held tester or the OBD II scan tool.

    Result: 

    DTC output display

    Display (DTC output) Proceed to
    No output A
    P2A00 again. B

    B: REPLACE ECM (See  ENGINE CONTROL SYSTEM  ) AND PERFORM CONFIRMATION DRIVING PATTERN (See  WIRING DIAGRAM   ) 

    A: Go To Next Step 

  12. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST 

    OK: Vehicle has run out of the fuel in the past. 

    NO: CHECK FOR INTERMITTENT PROBLEMS (See  CHECK FOR INTERMITTENT PROBLEMS   ) 

    YES: DTC IS CAUSED BY RUNNING OUT OF FUEL 

  13. PERFORM CONFIRMATION DRIVING PATTERN (See  WIRING DIAGRAM   ) 

    HINT:

    Clear all DTCs prior to performing the confirmation driving pattern (see WIRING DIAGRAM  ).

    GO: Go To Next Step 

  14. READ OUTPUT DTC (SEE IF A/F SENSOR DTC IS OUTPUT AGAIN) 
    1. Connect the hand-held tester or the OBD II scan tool to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the hand-held tester or the OBD II scan tool ON.
    4. On the hand-held tester, select the item: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
    5. Read DTCs using the hand-held tester or the OBD II scan tool.

    Result: 

    DTC output display

    Display (DTC output) Proceed to
    P2A00 A
    No output B

    B: Go to step   18 

    A: Go To Next Step 

  15. REPLACE AIR FUEL RATIO SENSOR 

    GO: Go To Next Step 

  16. PERFORM CONFIRMATION DRIVING PATTERN (See  WIRING DIAGRAM   ) 

    HINT:

    Clear all DTCs prior to performing the confirmation driving pattern (see WIRING DIAGRAM  ).

    GO: Go To Next Step 

  17. READ OUTPUT DTC (SEE IF A/F SENSOR DTC IS OUTPUT AGAIN) 
    1. Connect the hand-held tester or the OBD II scan tool to the DLC3.
    2. Turn the power switch ON (IG).
    3. Turn the hand-held tester or the OBD II scan tool ON.
    4. On the hand-held tester, select the item: DIAGNOSIS / ENHANCED OBD II / DTC INFO / CURRENT CODES.
    5. Read DTCs using the hand-held tester or the OBD II scan tool.

    Result: 

    DTC output display

    Display (DTC output) Proceed to
    No output A
    P2A00 B

    B: REPLACE ECM (See  ENGINE CONTROL SYSTEM  ) AND PERFORM CONFIRMATION DRIVING PATTERN (See  WIRING DIAGRAM   ) 

    A: Go To Next Step 

  18. CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST 

    OK: Vehicle has run out of the fuel in the past. 

    NO: CHECK FOR INTERMITTENT PROBLEMS (See  CHECK FOR INTERMITTENT PROBLEMS   ) 

    YES 

    DTC IS CAUSED BY RUNNING OUT OF FUEL