LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2004 >> Matrix Base, FWD, Automatic >> Repair and Diagnosis >> Suspension >> Wheel Alignment >> Rear Suspension System >> Rear Wheel Alignment (4WD) >> Adjustment

Rear Wheel Alignment (4WD): Adjustment

  1. INSPECT TIRE (See  INSPECTION  ) 
  2. MEASURE VEHICLE HEIGHT (See  ADJUSTMENT  ) 
    NOTE: Before inspecting the wheel alignment, adjust the vehicle height to the specified value.
  3. INSPECT TOE-IN 
    TOE-IN VALUE REFERENCE

    Toe-in (total) A + B: 0° 12' +/- 12' (0.20° +/- 0.20°) C - D: 2.0 +/- 2.0 mm (0.08 +/- 0.08 in.)

    If the toe-in is not within the specified value, inspect and replace the suspension parts as necessary.

    Fig 1: Inspecting Toe-In
    G02632906Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSPECT CAMBER 
    1. Install the camber-caster-kingpin gauge or position vehicle on wheel alignment tester.
    2. Inspect the camber.
      Camber VALUE REFERENCE

      Camber -0°44' +/- 45' (-0.73° +/- 0.75°)
      Right-left error 45' (0.75°) or less

      If the measured value is not within the specified value, inspect the suspension parts for damage and/or wear and replace them if necessary because camber is not adjustable.

  5. ADJUST CAMBER AND TOE-IN 
    1. Measure the distance from the LH lower suspension arm bracket set bolt to the RH axle carrier rear side set bolt as shown in Fig 2 .
    2. Measure the distance from the RH lower suspension arm bracket set bolt to the LH axle carrier rear side set bolt as shown in Fig 2 .
    3. Employ the same manner to the LH-RH.

      Length difference: 6.0 mm (0.236 in.) or less 

      If the difference exceeds the specified value, adjust it by turning the adjusting cams.

      Fig 2: Measuring Camber & Toe In
      G02632907Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Loosen the upper and lower suspension arm adjusting cam set nuts.
    5. Adjust the camber and toe-in by turning the adjusting cams.

      HINT:

      Try to adjust the camber and toe-in to the center of the specified values.

    6. Tighten the upper and lower suspension arm adjusting cam set nuts.
      Fig 3: Loosening Upper And Lower Suspension Arm Adjusting Cam Set Nuts
      G02632908Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 74 N.m (755 kgf.cm, 55 ft.lbf) 

      Fig 4: Identifying Cam Set Nut
      G02632909Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. How to read adjusting chart (using examples).
      1. Measure the present alignment.

        Example: 

        Camber (RH): +0°01' (+0.02°) 

        Camber (LH): -1°29' (-1.48°) 

        Toe-in (total): IN 6.0 mm (0.236 in.) 

      2. Mark the difference between the standard value (A) and the measured value (B) on the adjustment chart.

        Standard value: 

        Camber: -0°44' (-0.73°) 

        Toe-in (total): IN 2.0 mm (0.079 in.) 

        Formula: A - B = C 

        Camber: (RH): -0°44' - (+0°01') = -0°45' 

        Camber: (LH): -0°44' - (-1°29') = 0°45' 

        Toe-in (total): IN 2.0 - IN 6.0 = OUT 4.0 

        Toe-in (each side): OUT 2.0 

        Fig 5: Identifying Adjusting Chart
        G02632910Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. As shown in Fig 5 , read the distance from the marked point to center of the chart, and adjust the upper and/or lower arm adjusting cams accordingly.

      Amount to turn adjusting cams (by graduation): 

      Upper arm cam (RH): + (Inward) 3.2 

      Lower arm cam (RH): + (Inward) 0.8 

      Upper arm cam (LH): - (Outward) 2.3 

      Lower arm cam (LH): + (Inward) 1.0 

      Fig 6: Adjusting Amount Reference Chart
      G02632911Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002