LEMON Manuals: Even more car manuals for everyone

Back Window Glass (Sedan): Installation

  1. CLEAN AND SHAPE CONTACT SURFACE OF BODY 
    1. Using a knife, cut away any rough areas on the body.

      HINT:

      Leave as much of the adhesive on the body as possible.

    2. Clean the cut surface of the adhesive with a piece of shop rag saturated in cleaner.

    HINT:

    Even if all the adhesive has been removed, clean the body.

    Fig 1: Cleaning Contact Surface Of Body
    G02907200Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. CLEAN REMOVED GLASS 
    1. Remove the damaged stoppers.
    2. Using a scraper, remove the adhesive sticking to the glass.
    3. Clean the glass with cleaner.
    NOTE:
    • Be careful not to damage the glass. 
    • Do not touch the glass face after cleaning it. 
      Fig 2: Removing Adhesive Sticking To Glass
      G02907201Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL NEW STOPPERS 

    Attach new stoppers to the glass with the ceramic notches on the glass aligned with the stoppers as shown in Fig 3 .

    A: 15.9 mm (0.626 in.) 

    Fig 3: Attaching Stoppers To Glass With Ceramic Notches On Glass Aligned With Stoppers
    G02907202Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL NEW BACK WINDOW OUTSIDE MOULDING 

    Install new back window outside moulding to the back window glass as shown in Fig 4 .

    HINT:

    • Install the back window outside moulding from the center of the glass at the lower side of the vehicle.
    • When installing the back window outside moulding, do not stretch the moulding.
      Fig 4: Identifying Window Outside Moulding Dimensions
      G02907203Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. POSITION GLASS 
    1. Place the glass in the correct position.
    2. Check that all contacting parts of the glass rim are perfectly even.
    3. Place reference marks between the glass and body.
    4. Remove the glass.
      Fig 5: Placing Glass In Correct Position
      G02907204Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. CLEAN CONTACT SURFACE OF GLASS 

    Using a cleaner, clean the contact surface around the entire glass rim.

    NOTE: Do not touch the glass face after cleaning it. 
    Fig 6: Cleaning Contact Surface Around Entire Glass Rim
    G02907205Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. COAT CONTACT SURFACE OF BODY WITH PRIMER M 

    Using a brush, coat Primer M to the exposed part of the body on the vehicle side.

    NOTE:
    • Allow the primer coating to dry for 3 minutes or more. 
      Fig 7: Coating Primer M To Exposed Part Of Body On Vehicle Side
      G02907206Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. COAT CONTACT SURFACE OF GLASS WITH PRIMER G 
    1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G as shown in Fig 7 .
    2. When the primer is coated to the area other than that specified by accident, wipe it off with a clean shop rag before the primer dries.
    NOTE:
    • Allow the primer coating to dry for 3 minutes or more. 
    • Throw away any opened Primer G. 
      Fig 8: Identifying Edge Of Glass Dimensions
      G02907207Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. APPLY ADHESIVE 
    1. Cut off the tip of the cartridge nozzle.

      Part No. 08850-00801 or equivalent 

      HINT:

      After cutting off the tip, use all adhesive within the time described in APPLY ADHESIVE  .

      APPLY ADHESIVE

      Temperature Tackfree time
      35°C (95°F) 15 minutes
      20°C (68°F) 100 minutes
      5°C (41°F) 8 hours
    2. Load the cartridge into the sealer gun.
    3. Coat the glass with adhesive as shown in Fig 9 .

      Adhesive height: 12.5 mm (0.492 in.) 

      Adhesive width: 8.0 mm (0.315 in.) 

      A: 10.3 mm (0.406 in.) 

      B: 15.0 mm (0.591 in.) 

      Fig 9: Identifying Adhesive Dimensions
      G02907208Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSTALL GLASS 
    1. Position the glass so that the reference marks are lined up, and press in gently along the rim.
      Fig 10: Installing Glass
      G02907209Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT:

      Confirm that the moulding is attached to the body panel as shown in Fig 11 .

    2. Hold the back window glass in place securely with a protective tape or equivalent until the adhesive hardens.
    NOTE: Take care not to drive the vehicle during the time described in  TEMPERATURE   . 
    TEMPERATURE

    Temperature Minimum time prior to driving the vehicle
    35°C (95°F) 1.5 hours
    20°C (68°F) 5 hours
    5°C (41°F) 24 hours
    Fig 11: Identifying Moulding Attaching Position
    G02907210Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSPECT FOR LEAK AND REPAIR 
    NOTE: Conduct a leak test after the hardening time has elapsed. 

    Part No. 08833-00030 or equivalent 

  12. INSTALL PACKAGE TRAY SILENCER PAD 
  13. INSTALL PACKAGE TRAY TRIM PANEL 
    1. Install the seat belts through the cutout of the package tray trim.
    2. Install the package tray trim with the 2 clips.
      Fig 12: Installing Package Tray Trim Panel
      G02907211Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL HIGH-MOUNTED STOP LIGHT 
    1. Connect the connector.
    2. Install the high-mounted stop light as shown in Fig 13 .
      Fig 13: Installing High-Mounted Stop Light
      G02907212Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. 4-door vehicle: INSTALL ROOF SIDE INNER GARNISH 
    1. Install the roof side inner garnish to the body.
    2. Install the clip.
    3. Install the other using the same procedures described above.
      Fig 14: Installing Roof Side Inner Garnish
      G02907213Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  16. 4-door vehicle: INSTALL REAR SEAT SIDE GARNISH 
    1. Install the rear seat side garnish to the body.
    2. W/Split type rear seat:

      Install the rear seatback hinge with the bolt.

      Torque: 41 N.m (420 kgf.cm, 30 ft.lbf) 

    3. Install the rear seat outer belt floor anchor with the bolt.

      Torque: 41 N.m (420 kgf.cm, 30 ft.lbf) 

    4. Install the other using the same procedures described above.
      Fig 15: Installing Rear Seat Side Garnish
      G02907214Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. 2-door vehicle: INSTALL ROOF SIDE INNER GARNISH 
    1. Install the roof side inner garnish to the body.
    2. Install the clips.
    3. Install the front seat outer belt shoulder anchor with the bolt.

      Torque: 41 N.m (420 kgf.cm, 30 ft.lbf) 

    4. Install the seat belt shoulder anchor cover cap.
      Fig 16: Installing Roof Side Inner Garnish
      G02907215Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. 2-door vehicle: INSTALL QUARTER TRIM 
    1. Install the quarter trim to the body.
    2. w/ Split type rear seat:

      Install the rear seatback hinge with the bolt.

      Torque: 41 N.m (420 kgf.cm, 30 ft.lbf) 

    3. Install the rear seat outer belt floor anchor with the bolt.

      Torque: 41 N.m (420 kgf.cm, 30 ft.lbf) 

  19. INSTALL REAR SEATBACK (See  INSTALLATION  or  INSTALLATION  ) 
  20. INSTALL REAR SEAT CUSHION (See  INSTALLATION  or  INSTALLATION  ) 
  21. 4-door vehicle: INSTALL REAR DOOR OPENING TRIMS 
  22. 4-door vehicle: INSTALL REAR DOOR SCUFF PLATES 
  23. 2-door vehicle: INSTALL FRONT DOOR OPENING TRIM 
  24. 2-door vehicle: INSTALL FRONT DOOR SCUFF PLATES 
    Fig 17: Installing Quarter Trim
    G02907216Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002