LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2003 >> Sequoia SR5, 4WD >> Repair and Diagnosis >> Body & Frame >> Windows >> Quarter Window Glass >> Removal

Quarter Window Glass: Removal

  1. w/ Rear No. 2 seat: REMOVE REAR NO. 2 SEAT 
  2. REMOVE REAR DOOR SCUFF PLATE 
    Fig 1: Removing Rear Door Scuff Plate
    G02852481Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Remove the 3 screws.
    2. Using a screwdriver, remove the rear door scuff plate.
      NOTE: Tape the screwdriver tip before use.
  3. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP 
  4. REMOVE DOME LIGHT 
    Fig 2: Removing Dome Light Cover
    G02852482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Using a screwdriver, remove the lens.
      NOTE: Tape the screwdriver tip before use.
    2. Remove the 2 screws and dome light, then disconnect the connector.
  5. REMOVE REAR TRIM COVER 
    Fig 3: Identifying Rear Trim Cover
    G02852483Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Using a screwdriver, remove the rear trim cover.

    NOTE: Tape the screwdriver tip before use.
  6. REMOVE REAR TRIM 
    Fig 4: Removing Rear Trim
    G02852484Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Using a screwdriver, remove the rear trim.

    NOTE: Tape the screwdriver tip before use.
  7. REMOVE REAR FLOOR MAT SUPPORT PLATE 
  8. w/o Rear No. 2 seat: REMOVE QUARTER TRIM HOLE COVER 
    Fig 5: Removing Quarter Trim Hole Cover
    G02852485Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Using a screwdriver, remove the quarter trim hole cover.

    NOTE: Tape the screwdriver tip before use.
  9. w/ Rear No. 2 seat: REMOVE QUARTER TRIM UPPER BELT HOLE COVER 
    Fig 6: Removing Quarter Trim Upper Belt Hole Cover
    G02852486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Using a screwdriver, remove the quarter trim upper belt hole cover.

    NOTE: Tape the screwdriver tip before use.
  10. REMOVE QUARTER TRIM PANEL 
    1. w/o Tonneau cover:

      Using a screwdriver, remove the 2 No. 1 tonneau cover holder caps.

      NOTE: Tape the screwdriver tip before use.
    2. Remove the 2 package holder net hooks.
    3. Remove the rear No. 1 seat outer belt floor anchor.
      Fig 7: Removing Holder Net Hooks
      G02852487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 3 bolts, clip and quarter trim panel, then disconnect the connector.
  11. w/ Rear No. 2 seat: REMOVE REAR NO. 2 SEAT OUTER BELT SHOULDER ANCHOR 
    Fig 8: Removing Rear No. 2 Seat Outer Belt Shoulder Anchor
    G02852488Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE NO. 2 REAR WINDOW SIDE GARNISH 

    Remove the 2 clips and No. 2 rear window side garnish.

    Fig 9: Removing Rear No. 2 Rear Window Side Garnish
    G02852489Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE REAR NO. 1 SEAT OUTER BELT SHOULDER ANCHOR 
    1. Using a screwdriver, remove the anchor cap.
      NOTE: Tape the screwdriver tip before use.
    2. Remove the rear No. 1 seat outer belt shoulder anchor.
  14. REMOVE REAR WINDOW SIDE GARNISH 
    Fig 10: Removing Rear Window Side Garnish
    G02852490Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    Remove the rear window side garnish.

  15. REMOVE QUARTER WINDOW GLASS 
    1. w/ Glass antenna:

      Disconnect the connectors from the glass antenna terminals.

    2. Push a piano wire through from the interior.
    3. Tie both wire ends to wooden blocks or similar objects.
      NOTE: Apply protective tape to the outer surface to keep the surface from being scratched.
      Fig 11: Using Protective Tape To Protect Surface
      G02852491Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: When separating the glass, take care not to damage the paint and interior.
    4. Cut the adhesive by pulling the piano wire around it.
      NOTE: Cut the adhesive areas as shown in the illustration, leaving the adhesive where the clips are.
      Fig 12: Locating Clips
      G02852492Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Push the piano wire through as shown in the illustration, cut off the adhered part to the clips.
    6. Remove the glass.
      Fig 13: Removing Glass
      G02852493Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Leave as much of the adhesive on the body as possible when cutting off the glass.