LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2003 >> ECHO 4D Sedan, Automatic >> Repair and Diagnosis >> Suspension >> Wheel Alignment Specifications & Adjustment Procedures >> Inspection - Front

Inspection - Front

  1. MEASURE VEHICLE HEIGHT 

    Vehicle height:  Refer to VEHICLE HEIGHT SPECIFICATIONS  table.

    NOTE: Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

    If the vehicle height is not the specified value, try to adjust it by pushing down on or lifting the body.

    Fig 1: Measuring Ground Clearance
    G02826478Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL CAMBER-CASTER-KINGPIN GAUGE OR POSITION VEHICLE ON WHEEL ALIGNMENT TESTER 

    Follow the specific instructions of the equipment manufacturer.

  3. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION 

    Camber, caster and steering axis inclination:  Refer to FRONT CAMBER, CASTER & STEERING AXIS INCLINATION SPECIFICATIONS  table.

    Fig 2: Installing Camber-Caster-Kingpin Gauge/Positioning Vehicle On Wheel Alignment Tester
    G02826479Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    If the caster and steering axis inclination are not within the specified values, after the camber has been correctly adjusted, recheck the suspension parts for damaged and/or worn out parts.

  4. ADJUST CAMBER 
    NOTE: After the camber has been adjusted, inspect the toe-in.
    1. Remove the front wheel.
    2. Remove the 2 nuts on the lower side of the shock absorber.

      If reusing the bolts and/or nuts, coat the threads of nuts with engine oil.

    3. Clean the installation surfaces of the shock absorber and the steering knuckle.
    4. Temporarily install the 2 nuts.
      Fig 3: Locating Shock Absorber lower side nuts
      G02826481Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Adjust the camber by pushing or pulling the lower side of the shock absorber in the direction in which the camber adjustment is required.
    6. Tighten the nuts.

      Torque: 132 N.m (1,350 kgf.cm, 97 ft.lbf) 

    7. Install the front wheel.

      Torque: 103 N.m (1,050 kgf.cm, 76 ft.lbf) 

    8. Check the camber.

      HINT:

      • Try to adjust the camber to the center of the specified value.
      • Adjusting value for the set bolts is 6' - 30' (0.1° - 0.5°).

      If the camber is not within the specified value, using Fig 5, estimate how much additional camber adjustment will be required, and select the camber adjusting bolt.

      NOTE: Tighten the adjusting bolt with a washer and a new nut.
      Fig 4: Adjusting Camber
      G02826482Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Fig 5: Bolt Specification Table
      G02826483Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Do the steps mentioned above again. At step  b, replace 1 or 2 selected bolts.

    HINT:

    When replacing the 2 bolts, replace 1 bolt for each time.

  5. INSPECT TOE-IN 

    Toe-in:  Refer to FRONT TOE-IN SPECIFICATIONS  table.

    If the toe-in is not within the specified value, adjust it at the rack ends.

  6. ADJUST TOE-IN 
    1. Remove the rack boot set clips.
      Fig 6: Inspecting Toe-in
      G02826484Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Loosen the tie rod end lock nuts.
    3. Turn the right and left rack ends by an equal amount to adjust the toe-in.

      HINT:

      Try to adjust the toe-in to the center of the specified value.

      Fig 7: Adjusting Toe-in
      G02826485Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Make sure that the lengths of the right and left rack ends are the same.

      Rack end length difference: 1.5 mm (0.059 in.) or less 

    5. Torque the tie rod end lock nuts.

      Torque: 

      Manual steering: 47 N.m (480 kgf.cm, 35 ft.lbf) 

      Power steering: 74 N.m (750 kgf.cm, 54 ft.lbf) 

    6. Place the boots on the seats and install the clips.

    HINT:

    Make sure that the boots are not twisted.

  7. INSPECT WHEEL ANGLE 

    Turn the steering wheel fully and measure the turning angle.

    Wheel turning angle:  Refer to FRONT WHEEL TURNING ANGLE SPECIFICATIONS  table.

    Fig 8: Location Rack End
    G02826486Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    If the right and left inside wheel angles differ from the specified value, check the right and left rack end lengths.

    Fig 9: Inspecting Wheel Angle
    G02826487Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002