LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2003 >> ECHO 4D Sedan, Automatic >> Repair and Diagnosis >> Steering >> Power Steering >> Power Steering Fluid >> Inspection

Power Steering Fluid: Inspection

  1. CHECK FLUID LEVEL 
    1. Keep the vehicle level.
    2. With the engine stopped, check the fluid level in the oil reservoir.

      If necessary, add fluid.

      Fluid: ATF DEXRON II or III 

      HINT:

      Check that the fluid level is within the HOT LEVEL range on the reservoir cap dipstick. If the fluid is cold, check that it is within the COLD LEVEL range.

    3. Start the engine and run it at idle.
    4. Turn the steering wheel from lock to lock several times to boost fluid temperature.

      Fluid temperature: 80°C (176°F) 

      Fig 1: Inspecting Fluid Level
      G02826500Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Check for foaming or emulsification.

      If there is foaming or emulsification, bleed power steering system (See BLEEDING ).

      Fig 2: Checking For Foaming OR Emulsification
      G02826501Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. With the engine idling, measure the fluid level in the oil reservoir.
    7. Stop the engine.
    8. Wait a few minutes and remeasure the fluid level in the oil reservoir.

      Maximum fluid level rise: 5 mm (0.20 in.) 

      If a problem is found, bleed power steering system (See BLEEDING ).

    9. Check the fluid level.
      Fig 3: Checking Level - Engine Idling/Engine Stopped
      G02826502Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. CHECK STEERING FLUID PRESSURE 
    1. Disconnect the pressure feed tube from the PS vane pump (See REMOVAL ).
    2. Connect SST, as shown in Fig 4.

      SST 09640-10010 (09641-01010, 09641-01030, 09641-01060)

      NOTE: Check that the valve of the SST is in the open position.
      Fig 4: Installing SST Attachments
      G02826503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Bleed the power steering system (See BLEEDING ).
    4. Start the engine and run it at idle.
    5. Turn the steering wheel from lock to lock several times to boost fluid temperature.

      Fluid temperature: 80°C (176 °F) 

    6. With the engine idling, close the valve of the SST and observe the reading on the SST.

      Minimum fluid pressure: 5,400 kPa (55 kgf/cm 2  , 781 psi) 

      NOTE:
      • Do not keep the valve closed for more than 10 seconds.
      • Do not let the fluid temperature become too high.
      Fig 5: Measuring Fluid Pressure Using SST - Valve Closed
      G02826504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. With the engine idling, open the valve fully.
      Fig 6: Measuring Fluid Pressure Using SST - Valve Open
      G02826505Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Measure the Fluid pressure at engine speeds of 1,000 rpm and 3,000 rpm.

      Difference fluid pressure: 

      490 kPa (5 kgf/cm2 , 71 psi) or less

      NOTE: Do not turn the steering wheel.
    9. With the engine idling and valve fully opened, turn the steering wheel to full lock position.

      Minimum fluid pressure: 

      5,400 kPa (55 kgf/cm 2  , 781 psi) 

      NOTE:
      • Do not maintain lock position for more than 10 seconds.
      • Do not let the fluid temperature become too high.
      Fig 7: Measuring Fluid Pressure Using SST - Valve Open/Wheel To Full Lock Position
      G02826506Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. Disconnect the SST.

      SST 09640-10010 (09641-01010, 09641-01030, 09641-01060)

    11. Connect the pressure feed tube to the PS vane pump (See INSTALLATION ).
    12. Bleed the power steering system (See BLEEDING ).