LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2003 >> Corolla CE, Automatic >> Repair and Diagnosis >> Restraints >> Restraints Control Systems >> Seat Belt >> Rear Seat Belt >> Replacement

Rear Seat Belt: Replacement

HINT:

Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.

  1. REMOVE REAR DOOR OPENING TRIM RH 
  2. REMOVE REAR DOOR OPENING TRIM LH 
  3. REMOVE REAR SEAT CUSHION ASSEMBLY (See  REAR SEAT (SEDAN WITH SEPARATE TYPE)  or  REAR SEAT ASSY (SEDAN WITH BENCH TYPE)  ) 
  4. REMOVE REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See  REAR SEAT ASSY (SEDAN WITH BENCH TYPE)  ) 
  5. REMOVE REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See  REAR SEAT (SEDAN WITH SEPARATE TYPE)  ) 
  6. REMOVE REAR SEAT SIDE COVER RH (FIXED TYPE REAR SEAT) (See  ROOF HEADLINING ASSY  ) 
  7. REMOVE REAR SEAT SIDE GARNISH LH (FIXED TYPE REAR SEAT) (See  ROOF HEADLINING ASSY  ) 
  8. REMOVE ROOM PARTITION BOARD LH (SEPARATED TYPE REAR SEAT) (See  ROOF HEADLINING ASSY  ) 
  9. REMOVE ROOM PARTITION BOARD RH (SEPARATED TYPE REAR SEAT) (See  ROOF HEADLINING ASSY  ) 
  10. REMOVE ROOF SIDE GARNISH INNER RH (See  ROOF HEADLINING ASSY  ) 
  11. REMOVE ROOF SIDE GARNISH INNER LH (See  ROOF HEADLINING ASSY  ) 
  12. REMOVE PACKAGE TRAY TRIM PANEL ASSY 
    1. Pull out the belt from the slit, and then remove the package tray trim panel assembly.
    Fig 1: Removing Package Tray Trim Panel Assembly
    G02825554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. REMOVE REAR SEAT 3 POINT TYPE BELT ASSY OUTER 
    1. Remove the bolt and disconnect the rear seat 3 point type belt assembly outer (floor anchor).
    2. Remove the bolt and rear seat 3 point type belt assembly outer.
  14. REMOVE REAR SEAT INNER W/CENTER BELT ASSY RH 
    1. Remove the 2 bolts and rear seat inner w/center belt assembly RH.
  15. REMOVE REAR SEAT INNER W/CENTER BELT ASSY LH 
    1. Remove the bolt and rear seat inner w/center belt assembly LH.
  16. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSY RH 
    1. Remove the 2 bolts and child restraint seat anchor bracket RH.
  17. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSY RH 
    1. Install the child restraint seat anchor bracket RH with the 2 bolts.

      Torque: 18.1 N.m (185 kgf.cm, 13.3 ft.lbf) 

  18. INSTALL REAR SEAT INNER W/CENTER BELT ASSY LH 
    1. Install the rear seat inner w/center belt assembly RH with the bolt, as shown in the illustration.

      Torque: 41.2 N.m (420 kgf.cm, 30 ft.lbf) 

      NOTE:
      • Do not make the anchor part run onto the protrusion part of the floor panel.
      • Do not disassemble the retractor.
      Fig 2: Installing Rear Seat Inner W/Center Belt Assembly RH
      G02825555Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the degree of tilt when the belt begins to lock the ELR.
      1. Check that the belt will not lock within 15 degrees of tilt in all the direction but the belt will lock over 45 degrees of tilt when moving the installed retractor gently.

      If the operation is not as specified, replace the rear seat belt assembly outer center.

    3. Install the rear seat belt assembly outer center with the bolt.

      Torque: 41.2 N.m (420 kgf.cm, 30 ft.lbf) 

    4. Check the ELR lock.
      Fig 3: Checking Degree Of Tilt
      G02825556Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Check should be performed with the assembly installed.
      1. Check that the belt will lock when pulling out the belt quickly with the belt installed.

      If the operation is not as specified, replace the rear seat belt assembly outer center.

    5. Check the fastening function of the child restraint system.
      NOTE: Check should be performed with the assembly installed.
      1. Check that the belt cannot be pulled out any more but can be rewound after the belt is fully pulled out.
      2. Check that the belt can be pulled out and rewound after the belt is fully rewound.

      If the operation is not as specified, replace the rear seat belt assembly outer center.

  19. INSTALL REAR SEAT INNER W/CENTER BELT ASSY RH 
    1. Install the rear seat inner w/center belt assembly RH with the bolt, as shown in the illustration.

      Torque: 41.2 N.m (420 kgf.cm, 30 ft.lbf) 

      NOTE: Do not make the anchor part run onto the protrusion part of the floor panel.
    Fig 4: Installing Rear Seat Inner W/Center Belt Assembly RH
    G02825557Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  20. INSTALL REAR SEAT 3 POINT TYPE BELT ASSY OUTER 
    NOTE: Do not disassemble the retractor.
    1. Check the degree of tilt when the belt begins to lock the ELR.
      1. Check that the belt will not lock within 15 degrees of tilt in all the direction but the belt will lock over 45 degrees of tilt when moving the installed retractor gently.

      If the operation is not as specified, replace the rear seat belt assembly outer.

      Fig 5: Checking Degree Of Tilt
      G02825558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the rear seat belt assembly outer (retractor side) with the bolt.

      Torque: 41.2 N.m (420 kgf.cm, 30 ft.lbf) 

    3. Install the rear seat belt assembly outer (floor anchor side) with the bolt.

      Torque: 41.2 N.m (420 kgf.cm, 30 ft.lbf) 

      NOTE: Do not make the anchor part run onto the protrusion part of the floor panel.
    4. Check the ELR lock.
      Fig 6: Installing Rear Seat Belt Assembly Outer (Floor Anchor Side)
      G02825559Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE: Check should be performed with the assembly installed.
      1. Check that the belt will lock when pulling out the belt quickly with the belt installed.

      If the operation is not as specified, replace the rear seat belt assembly outer.

    5. Check the fastening function of the child restraint system.
      NOTE: Check should be performed with the assembly installed.
      1. Check that the belt cannot be pulled out any more but can be rewound after the belt is fully pulled out.
      2. Check that the belt can be pulled out and rewound after the belt is fully rewound.

      If the operation is not as specified, replace the rear seat belt assembly outer.

  21. INSTALL ROOM PARTITION BOARD RH (SEPARATED TYPE REAR SEAT) 
  22. INSTALL ROOM PARTITION BOARD LH (SEPARATED TYPE REAR SEAT) 
  23. INSTALL REAR SEAT SIDE GARNISH LH (FIXED TYPE REAR SEAT) 
  24. INSTALL REAR SEAT SIDE COVER RH (FIXED TYPE REAR SEAT) 
  25. INSTALL REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See  REAR SEAT ASSY (SEDAN WITH BENCH TYPE)  ) 
  26. INSTALL REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See  REAR SEAT (SEDAN WITH SEPARATE TYPE)  )