LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2012 >> Impreza Sport Limited >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> Fuel Injection System (H4DO) (Except WRX-STI) >> Fuel Filler Pipe >> Installation

Fuel Filler Pipe: Installation

  1. Open the fuel filler lid.
  2. Insert the fuel filler pipe assembly into the rubber saucer from inside of the rear fender.
  3. Install the fuel filler pipe assembly to vehicle body.

    Tightening torque: 

    7.5 N.m (0.8 kgf-m, 5.5 ft-lb) 

    Fig 1: Locating Fuel Filler Pipe Assembly Mounting Bolt And Nut
    G08315524Courtesy of SUBARU OF AMERICA, INC.
  4. Install the rear mud guard RH. Refer to INSTALLATION , Mud Guard.
  5. Securely insert the fuel filler hose (A) and evaporation hose (B) until the hose end contacts the spool, then attach the clamp or clip as shown in the figure.

    Tightening torque: 

    2.5 N.m (0.3 kgf-m, 1.8 ft-lb) 

    Fig 2: Identifying Fuel Filler Hose And Evaporation Hose
    G08315525Courtesy of SUBARU OF AMERICA, INC.
    Fig 3: Identifying Hose, Spool, Pipe And Clamp/Clip
    G08315528Courtesy of SUBARU OF AMERICA, INC.
  6. Install the rear sub frame assembly.
    WARNING: A helper is required to perform this work.
    1. Support the rear sub frame assembly with a transmission jack.
    2. Support the rear sub frame assembly, and install the rear sub frame assembly to the body.

      Tightening torque: 

      T1: 70 N.m (7.1 kgf-m, 51.6 ft-lb) 

      T2: 145 N.m (14.8 kgf-m, 106.9 ft-lb) 

      Fig 4: Rear Sub Frame Assembly Mounting Nuts With Torque Specifications
      G08315529Courtesy of SUBARU OF AMERICA, INC.
    3. Install the lower side of the rear strut to the rear lateral link.
      NOTE: Use a new self-locking nut.

      Tightening torque: 

      120 N.m (12.2 kgf-m, 88.5 ft-lb) 

      Fig 5: Locating Rear Strut Assembly Lower Side Mounting Bolts And Nuts
      G08315522Courtesy of SUBARU OF AMERICA, INC.
  7. Install the rear vehicle height sensor and connect the connector (A) to the rear vehicle height sensor. (model with auto headlight beam leveler, left side only)

    Tightening torque: 

    7.5 N.m (0.8 kgf-m, 5.5 ft-lb) 

    Fig 6: Locating Rear Vehicle Height Sensor Connector Mounting Nuts
    G08315531Courtesy of SUBARU OF AMERICA, INC.
  8. Insert the parking brake cable into the back plate, and install it with the clamp.
    Fig 7: Locating Parking Brake Cable Mounting Clamps (LH/RH)
    G08315520Courtesy of SUBARU OF AMERICA, INC.
  9. Secure the parking brake cable with bolts.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.3 ft-lb) 

    Fig 8: Locating Parking Brake Cable Mounting Bolts
    G08315519Courtesy of SUBARU OF AMERICA, INC.
  10. Connect the parking brake cable to the parking brake assembly. Refer to INSTALLATION , Parking Brake Assembly (Rear Disc Brake).
  11. Install the fuel tank protector.
    NOTE: Use a new self-locking nut.

    Tightening torque: 

    T1: 9 N.m (0.9 kgf-m, 6.6 ft-lb) 

    T2: 18 N.m (1.8 kgf-m, 13.3 ft-lb) 

    Fig 9: Fuel Tank Protector Self-Locking Nut With Torque Specifications
    G08315534Courtesy of SUBARU OF AMERICA, INC.
  12. Install the propeller shaft. Refer to INSTALLATION , Propeller Shaft.
  13. Install the rear exhaust pipe and muffler. Refer to INSTALLATION , Rear Exhaust Pipe. Refer to INSTALLATION , Muffler.
  14. Install the rear disc brake assembly.

    Tightening torque: 

    66 N.m (6.7 kgf-m, 48.7 ft-lb) 

    Fig 10: Locating Rear Disc Brake Assembly Mounting Bolts (LH/RH)
    G08315535Courtesy of SUBARU OF AMERICA, INC.
  15. Install the rear brake hose bracket to the rear housing.

    Tightening torque: 

    33 N.m (3.4 kgf-m, 24.3 ft-lb) 

    Fig 11: Locating Rear Brake Hose Bracket Mounting Bolts (LH/RH)
    G08315516Courtesy of SUBARU OF AMERICA, INC.
  16. Install the rear ABS wheel speed sensor harness to the upper arm.
    NOTE: Prevent the harness identification (line) from being twisted when installing. (RH: Orange line, LH: Green line)
    Fig 12: Locating Rear ABS Wheel Speed Sensor Harness Connector And Mounting Bolts
    G08315515Courtesy of SUBARU OF AMERICA, INC.
  17. Attach the rear ABS wheel speed sensor to the rear housing.
    NOTE: Prevent the harness identification (line) from being twisted when installing. (RH: Orange line, LH: Green line)

    Tightening torque: 

    7.5 N.m (0.8 kgf-m, 5.5 ft-lb) 

    Fig 13: Locating ABS Wheel Speed Sensor Of Rear Housing (LH/RH)
    G08315514Courtesy of SUBARU OF AMERICA, INC.
  18. Lower the vehicle.
  19. Install the rear wheels.

    Tightening torque: 

    120 N.m (12.2 kgf-m, 88.5 ft-lb) 

  20. Connect the battery ground terminal.
    Fig 14: Connecting/Disconnecting Battery Ground Cable
    G08317298Courtesy of SUBARU OF AMERICA, INC.
  21. Inspect the wheel alignment and adjust if necessary.
  22. Perform reinitialization of the auto headlight beam leveler system. (model with auto headlight beam leveler) Refer to PROCEDURE , Auto Headlight Beam Leveler System.