LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2005 >> Outback R >> Repair and Diagnosis >> Transmission >> Automatic Trans >> Automatic Transmission (5AT) >> Automatic Transmission >> Drive Pinion Shaft Assembly >> Assembly

Drive Pinion Shaft Assembly: Assembly

  1. Measure the dimension "A" of drive pinion shaft.

    ST 398643600 GAUGE

    Fig 1: Measuring Dimension "A" Of Drive Pinion Shaft Using Gauge ST 398643600
    G03831803Courtesy of SUBARU OF AMERICA, INC.
  2. Using a press, press-fit the new roller bearing into specified position.
    NOTE: If excessive force is applied to roller bearing, the roller bearing will not turn easily.
    Fig 2: Installing New Roller Bearing
    G03831804Courtesy of SUBARU OF AMERICA, INC.
  3. After fitting a new O-ring to the shaft, attach the drive pinion collar to shaft.
  4. Install the lock washer to drive pinion shaft in proper direction.
  5. Tighten new lock nuts using ST1, ST2 and ST3. Calculate the lock washer and lock nut specifications using following formula.

    T2 = L2/(L1 + L2) x T1

    T1: 116 N.m (11.8 kgf-m, 85.3 ft-lb)

    [Required torque setting]

    T2: Tightening torque

    L1: ST2 length 0.072 m (2.83 in)

    L2: Torque wrench length

    Example:

    TORQUE WRENCH LENGTH AND TIGHTENING TORQUE SPECIFICATION

    Torque wrench length m (in) Tightening torque N.m (kgf-m, ft-lb)
    0.4 (15.75) 98 (10.0, 72)
    0.45 (17.72) 100 (10.2, 73.8)
    0.5 (19.69) 101 (10.3, 74.5)
    0.55 (21.65) 102 (10.4, 75)

    ST1 18667AA010 HOLDER

    ST2 499787700 WRENCH

    ST3 499787500 ADAPTER

    NOTE: Install the ST2 to torque wrench as straight as possible.
    Fig 3: Tightening Lock Nut Using Holder ST1 18667AA010, Wrench ST2 499787700 And Adapter ST3 499787500
    G03831805Courtesy of SUBARU OF AMERICA, INC.
  6. Measure the starting torque of bearing. Make sure the starting torque is within the specified range. If the torque is not within specified range, replace the roller bearing.

    Starting torque: 

    7.6-38.1 N (0.776-3.88 kgf, 1.7-8.6 lb) 

    Fig 4: Measuring Starting Torque Of Bearing
    G03831806Courtesy of SUBARU OF AMERICA, INC.
  7. Stake the caulking of lock nut at two points.
  8. Measure the dimension "B" of drive pinion shaft.

    ST 398643600 GAUGE

    Fig 5: Measuring Dimension Of Drive Pinion Shaft Using Gauge ST 398643600
    G03831807Courtesy of SUBARU OF AMERICA, INC.
  9. Calculate the thickness "t" (mm) of drive pinion shim.

    t = 6.5 +/- 0.0625 - (B - A)

  10. Select three or less shims from following table.
    DRIVE PINION SHIM THICKNESS SPECIFICATION

    Drive pinion shim
    Part Number Thickness mm (in)
    31451AA180 0.150 (0.0059)
    31451AA190 0.175 (0.0069)
    31451AA200 0.200 (0.0079)
    31451AA210 0.225 (0.0089)
    31451AA220 0.250 (0.0098)
    31451AA230 0.275 (0.0108)