LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2005 >> Impreza WRX STi >> Repair and Diagnosis >> Engine Performance >> Engine Control Systems >> FUEL INJECTION (FUEL SYSTEMS) -- STi >> Intake Manifold >> Assembly

Intake Manifold: Assembly

NOTE: Replace the gasket with a new one.
  1. Install the tumble generator valve assembly to the intake manifold.

    Tightening torque: 

    8.25 N.m (0.84 kgf-m, 6.1 ft-lb) 

    Fig 1: Installing Tumble Generator Valve Assembly To Intake Manifold
    G03817867Courtesy of SUBARU OF AMERICA, INC.
  2. Install the air intake duct to the intake manifold.

    Tightening torque: 

    19 N.m (1.94 kgf-m, 13.7 ft-lb) 

    Fig 2: Installing Air Intake Duct To Intake Manifold
    G03817868Courtesy of SUBARU OF AMERICA, INC.
  3. Install the fuel pipe assembly and pressure regulator to the intake manifold.

    Tightening torque: 

    4.9 N.m (0.5 kgf-m, 3.6 ft-lb) 

    Fig 3: Installing Fuel Pipe Assembly And Pressure Regulator To Intake Manifold
    G03817869Courtesy of SUBARU OF AMERICA, INC.
  4. Install the fuel injector pipe LH.
  5. Connect the left side fuel hose to injector pipe, and tighten the clamp screw.
    Fig 4: Connecting Left Side Fuel Hose To Injector Pipe, And Tighten Clamp Screw
    G03817870Courtesy of SUBARU OF AMERICA, INC.
  6. Install the fuel injector pipe RH.
  7. Connect the right side fuel hose to injector pipe, and tighten the clamp screw.
    Fig 5: Connecting Right Side Fuel Hose To Injector Pipe, And Tighten Clamp Screw
    G03817871Courtesy of SUBARU OF AMERICA, INC.
  8. Install the engine harness to the intake manifold.
  9. Install the harness bracket which holds the engine harness onto intake manifold.

    Tightening torque: 

    19 N.m (1.94 kgf-m, 13.7 ft-lb) 

    Fig 6: Installing Harness Bracket
    G03817872Courtesy of SUBARU OF AMERICA, INC.
  10. Tighten the bolts which install the fuel injector pipe onto intake manifold.

    Tightening torque: 

    19 N.m (1.94 kgf-m, 13.7 ft-lb) 

    • LH SIDE
      Fig 7: Tightening Bolts And Installing Fuel Injector Pipe Onto Intake Manifold LH Side (1 Of 2)
      G03817873Courtesy of SUBARU OF AMERICA, INC.
      Fig 8: Tightening Bolts And Installing Fuel Injector Pipe Onto Intake Manifold LH Side (2 Of 2)
      G03817874Courtesy of SUBARU OF AMERICA, INC.
    • RH SIDE
      Fig 9: Tightening Bolts And Installing Fuel Injector Pipe Onto Intake Manifold RH Side (1 Of 2)
      G03817875Courtesy of SUBARU OF AMERICA, INC.
      Fig 10: Tightening Bolts And Installing Fuel Injector Pipe Onto Intake Manifold RH Side (2 Of 2)
      G03817876Courtesy of SUBARU OF AMERICA, INC.
  11. Tighten the two bolts which install the fuel pipes on the left side of intake manifold.

    Tightening torque: 

    4.9 N.m (0.5 kgf-m, 3.6 ft-lb) 

    Fig 11: Tightening Two Bolts And Installing Fuel Pipes On Left Side Of Intake Manifold
    G03817877Courtesy of SUBARU OF AMERICA, INC.
  12. Connect the evaporation hoses to the purge valve.
    NOTE: Connect the evaporation hoses as shown in Fig 12 .
    Fig 12: Connecting Evaporation Hoses To Purge Valve
    G03817878Courtesy of SUBARU OF AMERICA, INC.
  13. Connect the evaporation hose and purge valve to the intake manifold.
    Fig 13: Connecting Evaporation Hose And Purge Valve To Intake Manifold
    G03817879Courtesy of SUBARU OF AMERICA, INC.
  14. Install the purge control solenoid valve.

    Tightening torque: 

    16 N.m (1.6 kgf-m, 11.8 ft-lb) 

    Fig 14: Installing Purge Control Solenoid Valve
    G03817880Courtesy of SUBARU OF AMERICA, INC.
  15. Connect the hoses to the purge control solenoid valve.
    NOTE: Connect the evaporation hoses as shown in Fig 15 .
    Fig 15: Connecting Hoses To Purge Control Solenoid Valve
    G03817881Courtesy of SUBARU OF AMERICA, INC.
  16. Connect the connector to the purge control solenoid valve.
  17. Connect the connector to the tumble generator valve sensor.
    Fig 16: Connecting Connector To Purge Control Solenoid Valve
    G03817882Courtesy of SUBARU OF AMERICA, INC.
  18. Connect the connector to the tumble generator valve actuator.
    Fig 17: Connecting Connector To Tumble Generator Valve Actuator
    G03817883Courtesy of SUBARU OF AMERICA, INC.
  19. Connect the connector to the fuel injector.
    Fig 18: Connecting Connector To Fuel Injector
    G03817884Courtesy of SUBARU OF AMERICA, INC.
  20. Install the throttle body to the intake manifold.
    NOTE: Replace the gasket with a new one.

    Tightening torque: 

    8 N.m (0.8 kgf-m, 5.8 ft-lb) 

    Fig 19: Installing Throttle Body To Intake Manifold
    G03817885Courtesy of SUBARU OF AMERICA, INC.
  21. Connect the connector to the throttle position sensor (A) and manifold absolute pressure sensor (B).
    Fig 20: Connecting Connector To Throttle Position Sensor (A) And Manifold Absolute Pressure Sensor (B)
    G03817886Courtesy of SUBARU OF AMERICA, INC.
  22. Install the engine ground terminal to the intake manifold.

    Tightening torque: 

    19 N.m (1.94 kgf-m, 13.7 ft-lb) 

    Fig 21: Installing Engine Ground Terminal To Intake Manifold (1 Of 2)
    G03817887Courtesy of SUBARU OF AMERICA, INC.
    Fig 22: Installing Engine Ground Terminal To Intake Manifold (2 Of 2)
    G03817888Courtesy of SUBARU OF AMERICA, INC.
  23. Install the fuel pipe protector RH.

    Tightening torque: 

    19 N.m (1.94 kgf-m, 13.7 ft-lb) 

    Fig 23: Installing Fuel Pipe Protector RH
    G03817889Courtesy of SUBARU OF AMERICA, INC.