LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2005 >> Impreza WRX STi >> Repair and Diagnosis >> Body & Frame >> Windows >> Glass/Window/Mirrors >> Front Door Glass >> Adjustment

Front Door Glass: Adjustment

NOTE: Before adjustment, ensure that all adjusting nuts of stabilizer (innner), upper stopper, and sash are loosened and door glass is raised so that it is in contact with weather strip.
  1. Temporarily tighten one adjusting bolt on one side of rear sash at the midpoint of slotted hole in the inner panel.
  2. Temporarily tighten the regulator B-channel in a position at the top of slotted hole.
  3. Lower the door glass 10 to 15 mm (0.39 to 0.59 in) from fully closed position. While applying outward pressure of 45.0+/-5.0 N (4.5+/-0.5 kgf, 9.9+/-1.1 lb) (F) to the upper edge of glass above midpoint of stabilizer (Outer), press the stabilizer (Inner) at pressure of 30+/-5 N (3.0+/-0.5 kgf, 6.6+/-1.1 lb) to the glass, then secure it.
    Fig 1: Tightening Regulator B-Channel
    G03816240Courtesy of SUBARU OF AMERICA, INC.
  4. For adjustment of clearance between front glass and center pillar cover, loosen the nuts (A), and move the glass sash back and forward until clearance becomes the value shown in Fig 3.
    Fig 2: Identifying Front Glass And Center Pillar Cover (1 Of 2)
    G03816241Courtesy of SUBARU OF AMERICA, INC.
    Fig 3: Identifying Front Glass And Center Pillar Cover (2 Of 2)
    G03816242Courtesy of SUBARU OF AMERICA, INC.
  5. For adjustment of upper and lower ends of center pillar, loosen the adjusting nut (A) of B-channel (B).
    Fig 4: Loosening Adjusting Nut (A) Of B-Channel (B)
    G03816243Courtesy of SUBARU OF AMERICA, INC.
  6. Adjust so that the upper and lower ends of center pillar are the same size.
    Fig 5: Adjusting Upper And Lower Ends Of Center Pillar
    G03816244Courtesy of SUBARU OF AMERICA, INC.
  7. For glass stroke adjustment, set the ST on glass and close the door, raise glass until positional relationship between glass and weather strip becomes as shown in Fig 6. And secure the glass so that the upper stopper lightly touches the glass holder.

    ST 61299AE000 SPACER (For front door glass of thickness 5 mm (0.197 in))

    Fig 6: Adjusting Glass Stroke
    G03816245Courtesy of SUBARU OF AMERICA, INC.

    For preventing wind noise, adjust the glass at the position where tip of gusset is raised up a little.

    Fig 7: Adjusting Glass Position At Tip Of Gusset
    G03816246Courtesy of SUBARU OF AMERICA, INC.
  8. After stabilizer adjustment, carry out the glass crimp adjustment. First, visually ensure positional relationship between retainer & molding and glass of the roof side, and then begin with rear sash adjustment. Set the ST on glass, and then adjust two adjusting bolts alternately step by step to obtain dimensions shown in (cross-section A)Fig 8.

    ST 61299AE000 SPACER (For front door glass of thickness 5 mm (0.197 in))

    NOTE: If two nuts are loosened at the same time, sash moves back and forth. Therefore, when one nut is adjusted, leave the other secured.
  9. Make the same adjustment of two adjusting bolts of rear sash.
    Fig 8: Adjusting Bolts Of Rear Sash
    G03816247Courtesy of SUBARU OF AMERICA, INC.
    NOTE: Do not tilt the sash bracket to inner panel during adjustment. Otherwise smooth regulator operation cannot be achieved.
    Fig 9: Adjusting Sash Bracket To Inner Panel
    G03816248Courtesy of SUBARU OF AMERICA, INC.
  10. Make adjustment of front sash in the same manner as that of rear sash.
    NOTE: Although front and rear sashes must, as a rule, be adjusted in the same manner, in some door installation, the adjustment in a different manner may be required. However, adjustment of one sash to the maximum amount and the other to the minimum amount is not permitted. Such adjustment may result in application of excessive load to regulator.
  11. After adjustments, tighten the nuts.
  12. After adjustment to glass, close the door. If there is a gap between outer lip of gusset and glass surface, adjust the gap with adjusting bolt (A) in lower fitting part of the gusset to prevent generation of wind noise.
  13. During adjustments, loosen the other three clamping bolts.
    Fig 10: Adjusting Front And Rear Sashes
    G03816249Courtesy of SUBARU OF AMERICA, INC.
  14. After adjustment, tighten the bolts and nuts.