LEMON Manuals: Even more car manuals for everyone

Valve Clearance Inspection: 2.0L

  1. Disconnect negative battery cable. See Fig 1 .
  2. Remove air intake duct. See Fig 2 .
  3. Remove one bolt from right side timing belt cover.
  4. Raise and support vehicle.
  5. Remove under cover from underneath vehicle. See Fig 3 . Remove the remaining timing belt cover retaining bolts.
  6. Lower the vehicle.
  7. When inspecting No. 1 and No. 3 cylinders; remove engine harness connector and bracket from the air cleaner cover. See Fig 4 . Remove air cleaner case. Remove ignition coils from cylinders No. 1 and No. 3. See Fig 5 . Remove PCV hose from rocker arm cover. Remove the bolts and remove the rocker arm cover.
  8. When inspecting No. 2 and No. 4 cylinders; disconnect battery cables and remove battery and battery carrier. Remove engine harness connector bracket. See Fig 6 . Disconnect washer motor electrical connectors. Remove washer tank mounting bolts. See Fig 7 . Postion washer tank out of the way. See Fig 8 . Remove ignition coils from cylinders No. 2 and No. 4. See Fig 9 . Remove PCV hose from rocker arm cover. Remove the bolts and remove the rocker arm cover.
  9. CAUTION: Insert the thickness gauge in as horizontal a direction as possible with respect to the valve stem end face. Measure the exhaust valve clearances while lifting-up the vehicle. See VALVE CLEARANCE SPECIFICATION (2.0L & 2.5L)  table.
  10. Turn crankshaft pulley clockwise until the arrow mark on the camshaft sprocket is in the position shown. See Fig 10 . Measure valve clearances on cylinder No. 1 intake valve and cylinder No. 3 exhaust valve. See Fig 11 .
  11. Rotate crankshaft pulley clockwise until the arrow mark on the camshaft sprocket is in the position shown. See Fig 12 . Measure valve clearances on cylinder No. 2 exhaust valve and cylinder No. 3 intake valve.
  12. Rotate crankshaft pulley clockwise until the arrow mark on the camshaft sprocket is in the position shown. See Fig 13 . Measure valve clearances on cylinder No. 2 intake valve and cylinder No. 4 exhaust valve.
  13. Rotate crankshaft pulley clockwise until the arrow mark on the camshaft sprocket is in the position shown. See Fig 14 . Measure valve clearances on cylinder No. 1 exhaust valve and cylinder No. 4 intake valve.
  14. If necessary, adjust the valve clearance. See 2.0L  under VALVE ADJUSTMENT. After inspection, install the related parts in the reverse order of removal.
VALVE CLEARANCE SPECIFICATION (2.0L & 2.5L)

Application Clearance - In. (mm)
2.0L & 2.5L
Intake 0.007-0.009 (0.18-0.23)
Exhaust 0.009-0.011 (0.23-0.27)
Fig 1: Disconnecting Ground Terminal From Battery
G00157456Courtesy of SUBARU OF AMERICA, INC.
Fig 2: Removing Air Intake Duct
G00157458Courtesy of SUBARU OF AMERICA, INC.
Fig 3: Removing Under Cover
G00157464Courtesy of SUBARU OF AMERICA, INC.
Fig 4: Removing Engine Harness Connector From Air Cleaner Cover
G00231704Courtesy of SUBARU OF AMERICA, INC.
Fig 5: Removing Ignition Coils (2.0L)
G00231705Courtesy of SUBARU OF AMERICE, INC.
Fig 6: Removing Engine Harness Connector Bracket
G00231706Courtesy of SUBARU OF AMERICA, INC.
Fig 7: Removing Washer Tank Mounting Bolts
G00157473Courtesy of SUBARU OF AMERICA, INC.
Fig 8: Securing Washer Tank Away From Work Area
G00157460Courtesy of SUBARU OF AMERICA, INC.
Fig 9: Removing Ignition Coils (2.0L - Driver's Side)
G00231707Courtesy of SUBARU OF AMERICA, INC.
Fig 10: Identifying Camshaft Sprocket Arrow Mark Location (1 Of 4)
G00231708Courtesy of SUBARU OF AMERICA, INC.
Fig 11: Measuring Valve Clearance (2.0L)
G00231709Courtesy of SUBARU OF AMERICA, INC.
Fig 12: Identifying Camshaft Arrow Mark Location (2 Of 4)
G00231710Courtesy of SUBARU OF AMERICA, INC.
Fig 13: Identifying Camshaft Arrow Mark Location (3 Of 4)
G00231711Courtesy of SUBARU OF AMERICA, INC.
Fig 14: Indentifying Camshaft Arrow Mark Location (4 Of 4)
G00231712Courtesy of SUBARU OF AMERICA, INC.