LEMON Manuals: Even more car manuals for everyone

Installation [06/2015 - ]: Procedure

  1. INSTALL FUEL INJECTOR ASSEMBLY 

    HINT: 

    Perform "Inspection After Repair" after replacing a fuel injector assembly.

    Refer to INITIALIZATION [06/2015 - ]

    1. Apply a light coat of gasoline or spindle oil to new injector vibration insulators and new O-rings, and then install one to each fuel injector assembly.
      GTY489597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 O-ring
      *2 Injector Vibration Insulator
    2. Apply a light coat of gasoline or spindle oil where the fuel delivery pipe sub-assembly contacts each O-ring.
    3. While turning the fuel injector assembly left and right, install it to the fuel delivery pipe sub-assembly.
      GTY488729Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Turn
      Push
      NOTE:
      • Do not damage the fuel injector assembly or O-ring.
      • Make sure that the O-ring is not twisted or moved out of place when installing the fuel injector assembly.
      • After installing each fuel injector assembly, check that it turns smoothly. If not, replace the O-ring with a new one.

      HINT: 

      Use the same procedure to install the other fuel injector assemblies.

  2. INSTALL NO. 1 DELIVERY PIPE SPACER 
    1. Install the 2 No. 1 delivery pipe spacers to the cylinder head sub-assembly.
      GTY495121Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fuel Delivery Pipe Sub-assembly Side
      *b Cylinder Head Sub-assembly Side
      NOTE:

      Install the No. 1 delivery pipe spacers in the correct direction.

  3. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY 
    1. Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies with the 2 bolts.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

      NOTE:
      • Be careful not to drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.
      • Check that the fuel injector assemblies turn smoothly after installing the fuel delivery pipe sub-assembly.
    2. Install the clamp of the fuel delivery pipe sub-assembly to the cylinder head sub-assembly with the bolt.

      Torque: 21 N*m (214 kgf*cm, 15 ft.*lbf) 

  4. INSTALL VACUUM SENSOR BRACKET 

    Refer to PROCEDURE - Step 6

  5. INSTALL VACUUM SENSOR (MANIFOLD ABSOLUTE PRESSURE SENSOR) 

    Refer to PROCEDURE - Step 1

  6. CONNECT FUEL TUBE SUB-ASSEMBLY 
    1. Connect the fuel tube sub-assembly to the fuel delivery pipe sub-assembly.

      Refer to PRECAUTION [06/2015 - ]

    2. Type A:
      1. Install the No. 2 fuel pipe clamp.
    3. Type B:
      1. Engage the 2 claws to install a new No. 2 fuel pipe clamp.
  7. INSTALL WIRE HARNESS CLAMP BRACKET 
    1. Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 nuts.

      Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf) 

  8. CONNECT ENGINE WIRE 

    Refer to PROCEDURE - Step 6

  9. INSTALL BATTERY 

    Refer to PROCEDURE - Step 54

  10. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 55

  11. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [06/2015 - ]

  13. INSPECT FOR FUEL LEAK 

    Refer to PROCEDURE - Step 1

  14. INSTALL NO. 2 CYLINDER HEAD COVER 

    Refer to PROCEDURE - Step 82

  15. PERFORM INITIALIZATION 
    1. Perform "Inspection After Repair" after replacing a fuel injector assembly.

      Refer to INITIALIZATION [06/2015 - ]