LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2016 >> iM Automatic CVT Trans >> Repair and Diagnosis >> Brakes >> Brakes Control Systems >> Brake Control System - Service Information >> Brake Actuator >> Installation [06/2015 - ] >> Procedure

Installation [06/2015 - ]: Procedure

  1. INSTALL BRAKE ACTUATOR ASSEMBLY 
    1. Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts.
      GTY491757Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      NOTE:
      • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.
      • Do not hold the brake actuator assembly by the connector.
      • Tighten the 3 bolts in the order shown in the illustration.
  2. INSTALL BRAKE ACTUATOR WITH BRACKET 
    1. Install the brake actuator with bracket to the vehicle body with the 3 nuts.
      GTY484558Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

      NOTE:
      • Do not damage the brake lines, fuel lines or wire harness.
      • Tighten the 3 nuts in the order shown in the illustration.
    2. Engage each clamp to install the No. 2 fuel tube clamp and front No. 4 brake tube to the brake actuator bracket assembly.
      NOTE:

      Do not damage the brake lines or fuel lines.

    3. Temporarily tighten each brake line to the correct position on the brake actuator assembly as shown in the illustration.
      GTY485189Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a From 1st Chamber of Master Cylinder Sub-assembly
      *b From 2nd Chamber of Master Cylinder Sub-assembly
      *c To Front Wheel Cylinder Assembly LH
      *d To Rear Wheel Cylinder Assembly RH
      *e To Rear Wheel Cylinder Assembly LH
      *f To Front Wheel Cylinder Assembly RH
    4. Using a union nut wrench, fully tighten each brake line.

      Specified tightening torque (A) 

      Torque: 19.5 N*m (199 kgf*cm, 14 ft.*lbf) 

      Specified tightening torque (B) 

      Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

      GTY483881Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Torque Wrench Fulcrum Length
      NOTE:
      • Do not kink or damage the brake lines.
      • Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
      • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

      HINT: 

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Refer to PRECAUTION [06/2015 - ]

      • When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        (A): 17.36 N*m (177 kgf*cm, 13 ft.*lbf)

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

        (B): 13.38 N*m (136 kgf*cm, 10 ft.*lbf)

    5. Engage the clamp to install the wire harness to the brake actuator bracket assembly.
      GTY493624Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Connect the connector
      Push up the lock lever
    6. Connect the connector to the brake actuator assembly, and then push up the lock lever to apply the lock.
      NOTE:
      • Make sure that the connector is locked securely.
      • Make sure that the connector can be connected smoothly. Do not allow water, oil or dirt to enter.
    7. Connect the connector to the ECM.

      Refer to PROCEDURE - Step 3

  3. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 55

  4. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 3

  5. INSTALL NO. 2 CYLINDER HEAD COVER 

    Refer to PROCEDURE - Step 82

  6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [06/2015 - ]

  7. BLEED BRAKE SYSTEM 

    Refer to BLEEDING [06/2015 - ]

  8. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION 

    Refer to CALIBRATION [06/2015 - ]

  9. PERFORM TEST MODE INSPECTION 

    Refer to TEST MODE PROCEDURE [06/2015 - ]

  10. INSPECT BRAKE ACTUATOR USING TECHSTREAM 

    Refer to ON-VEHICLE INSPECTION [06/2015 - ] 

  11. CHECK FOR AND CLEAR DTCS 

    Refer to DTC CHECK / CLEAR [06/2015 - ]