LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2012 >> iQ >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostic Codes (P0365-P1603)) >> SFI System >> DTC P0617: Starter Relay Circuit High >> Procedure

DTC P0617: Starter Relay Circuit High: Procedure

  1. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    5. Read the value displayed on the Techstream when the ignition switch is turned to ON and the engine is started.

      OK

      Ignition Switch Position Techstream Display
      ON Close (Starter signal OFF)
      START Open (Starter signal ON)

    NG → See step   2 

    OK → See step   11 

  2. READ VALUE USING TECHSTREAM (STARTER SIGNAL) 
    1. Disconnect the park/neutral position switch assembly connector.
    2. Connect the Techstream to the DLC3.
    3. Turn the ignition switch to ON.
    4. Turn the Techstream on.
    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.
    6. Read the value displayed on the Techstream when the ignition switch is turned to ON.
      RESULT

      Result Proceed to
      Remains Open (Starter signal ON) A
      Close (Starter signal OFF) B

    B → See step   4 

    A: Go to next step 

  3. INSPECT ECM (STA TERMINAL VOLTAGE) 
    1. Disconnect the park/neutral position switch assembly connector.
    2. Disconnect the ECM connector.
      Fig 1: Identifying ECM Connector Terminals
      GTY347129Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to ECM)
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      A18-48 (STA) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   8 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY - ECM) 

  4. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Disconnect the park/neutral position switch assembly connector.
      Fig 2: Identifying Park/Neutral Position Switch Connector Terminal
      GTY341823Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      4 (B) - 5 (L) Shift lever in any position other than P or N 10 kΩ or higher
      2 (RB) - 5 (L) Always 10 kΩ or higher
      TEXT IN ILLUSTRATION

      *a Component without harness connected
      (Park/Neutral Position Switch Assembly)
      RESULT

      Result Proceed to
      Short between 4(B) and 5(L) A
      Short between 2(RB) and 5(L) B
      Within standard range C

    B → See step   10 

    C → See step   6 

    A: Go to next step 

  5. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Replace the park/neutral position switch assembly. Refer to REMOVAL .

    NEXT: Go to next step 

  6. INSPECT IGNITION SWITCH ASSEMBLY 
    1. Inspect the ignition switch. Refer to INSPECTION - Step 1 .

    NG → See step   9 

    OK: Go to next step 

  7. INSPECT ECM (NSW TERMINAL VOLTAGE) 
    1. Disconnect the park/neutral position switch assembly connector.
    2. Disconnect the ECM connector.
      Fig 3: Identifying ECM Connector Terminals
      GTY345751Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Turn the ignition switch to ON.
    4. Measure the voltage according to the value(s) in the table below.
      TEXT IN ILLUSTRATION

      *a Front view of wire harness connector
      (to ECM)
      RESULT

      Tester Connection Switch Condition Specified Condition Proceed to
      A18-25 (NSW) - Body ground Ignition switch ON 11 to 14 V A
      Below 1.5 V B

    B → See step   8 

    A → REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - PARK/NEUTRAL POSITION SWITCH - ECM) 

  8. REPLACE ECM. Refer to  REMOVAL 
  9. REPLACE IGNITION SWITCH ASSEMBLY. Refer to  REMOVAL 
  10. REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY. Refer to  REMOVAL 
  11. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS