LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2010 >> xB Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Diagnostic Codes (P0010-P0451) >> SFI System >> DTC P0420: Catalyst System Efficiency Below Threshold (Bank 1) >> Procedure

DTC P0420: Catalyst System Efficiency Below Threshold (Bank 1): Procedure

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream ON.
    4. Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.
    5. Read DTCs.
      RESULT

      Result Proceed to
      P0420 A
      P0420 and other DTCs B

      HINT: 

      If any DTCs other than P0420 are output, troubleshoot those DTCs first.

    B → See step   4 

    A: Go to next step 

  2. PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) 
    1. Connect the Techstream to the DLC3.
    2. Start the engine and warm it up.
    3. Turn the Techstream ON.
    4. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
    5. Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F sensor.
    6. Perform the Active Test operation with the engine in an idling condition (press the RIGHT or LEFT button to change the fuel injection volume).
    7. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS B1S1 and O2S B1S2) displayed on the Techstream.

      HINT: 

      • The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
      • Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

        Standard

        Tester Display
        (Sensor)
        Injection Volume Status Voltage
        AFS B1S1
        (A/F)
        +25% Rich Less than 3.1
        -12.5% Lean More than 3.4
        O2S B1S2
        (HO2)
        +25% Rich More than 0.55
        -12.5% Lean Less than 0.4
        RESULT

        Status
        AFS B1S1
        Status
        O2S B1S2
        A/F Condition and A/F and
        HO2 Sensors Condition
        Misfire Main Suspected Trouble Area Proceed to
        Lean/Rich Lean/Rich Normal -
        • Three-Way Catalytic Converter (TWC)
        • Gas leak from exhaust system
        A
        Lean Lean/Rich A/F sensor malfunction -
        • A/F sensor
        B
        Rich Lean/Rich A/F sensor malfunction -
        • A/F sensor
        Lean/Rich Lean HO2 sensor malfunction -
        • HO2 sensor
        • Gas leak from exhaust system
        C
        Lean/Rich Rich HO2 sensor malfunction -
        • HO2 sensor
        • Gas leak from exhaust system
        Lean Lean Actual air fuel ratio lean May occur
        • Extremely rich or lean actual air-fuel ratio
        • Gas leak from exhaust system
        D
        Rich Rich Actual air fuel ratio rich -
        • Extremely rich or lean actual air-fuel ratio
        • Gas leak from exhaust system

        Lean: During Control the Injection Volume for A/F sensor, the A/F sensor output voltage (AFS) is consistently more than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently less than 0.4 V.

        Rich: During Control the Injection Volume for A/F sensor, the AFS is consistently less than 3.1 V, and the O2S is consistently more than 0.55 V.

        Lean/Rich: During Control the Injection Volume for A/F sensor of the Active Test, the output voltage of the HO2 sensor alternates correctly.

    D → See step   6 

    C → See step   9 

    B → See step   5 

    A: Go to next step 

  3. CHECK FOR EXHAUST GAS LEAK 

    OK

    No gas leak.

    NG → REPAIR OR REPLACE EXHAUST GAS LEAK POINT 

    OK: Go to next step 

  4. GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART 
  5. REPLACE AIR FUEL RATIO SENSOR (SENSOR 1). Refer to  REMOVAL 
  6. CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO, AND GO TO STEP 3. Refer to  INSPECTION PROCEDURE  
  7. REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: FRONT CATALYST) 
    1. Replace the exhaust manifold converter sub-assembly. . Refer to COMPONENTS .

    NEXT → See step   8 

  8. REPLACE CENTER EXHAUST PIPE ASSEMBLY (TWC: REAR CATALYST). Refer to  COMPONENTS 
  9. CHECK FOR EXHAUST GAS LEAK 

    OK

    No gas leak.

    NG → REPAIR OR REPLACE EXHAUST GAS LEAK POINT 

    OK → See step   10 

  10. REPLACE HEATED OXYGEN SENSOR (SENSOR 2). Refer to  REMOVAL