LEMON Manuals: Even more car manuals for everyone
Home >> Scion >> 2005 >> xB Standard >> Repair and Diagnosis >> Electrical >> Charging Systems >> Starting & Charging >> Starter ASSY >> Overhaul

Starter ASSY: Overhaul

  1. REMOVE MAGNET SWITCH BODY 
    1. Remove the nut, and disconnect the lead wire from the magnet switch body.
      Fig 1: Disconnecting Lead Wire From Magnet Switch Body
      G03094987Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 2 screws holding the magnet switch body.
      Fig 2: Removing Magnet Switch Body Screws
      G03094988Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the magnet switch body.
    4. Remove the return spring and plunger.
  2. REMOVE STARTER COMMUTATOR END FRAME COVER 
    1. Using a screwdriver, remove the cover.
  3. REMOVE STARTER ARMATURE ASSY 
    1. Remove the 2 through bolts, and pull out the starter yoke assy and commutator end frame assy together.
      Fig 3: Pulling Out Starter Yoke Assy And Commutator End Frame Assy
      G03094989Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the starter yoke assy from the commutator end frame assy.
    3. Using snap ring pliers, remove the snap ring and plate washer.
      Fig 4: Removing Snap Ring And Plate Washer
      G03094990Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the starter armature assy from the commutator end frame assy.
  4. REMOVE STARTER ARMATURE PLATE 
    1. Remove the plate from the starter yoke.
  5. REMOVE PLANETARY GEAR 
    1. Remove the 3 planetary gears.
      Fig 5: Removing Planetary Gears
      G03094991Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSY 
    1. Remove the starter center bearing clutch with drive lever set pin from the starter drive housing.
    2. Remove the drive lever set pin from the starter center bearing clutch.
      Fig 6: Removing Starter Center Bearing Clutch Sub-Assy
      G03094992Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. INSPECT STARTER ARMATURE ASSY 
    1. Check the continuity.
      1. Using an ohmmeter, check that there is continuity between the segments of the commutator.

      If there is no continuity between the segments, replace the armature.

      Fig 7: Checking Continuity Between Segments Of Commutator
      G03094993Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the commutator for ground.
      1. Using an ohmmeter, check that there is no continuity between the commutator and armature coil core.

      If there is continuity, replace the armature.

      Fig 8: Checking For No Continuity Between Commutator And Armature Coil Core
      G03094994Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check the commutator surface for dirt or burnout.

      If the surface is dirty or burnt, correct it with 400-grit sandpaper or a lathe.

    4. Using vernier calipers, measure the commutator length.
      • Standard length: 3.1 mm (0.122 in.) 
      • Maximum length: 3.8 mm (0.150 in.) 

      If the length is greater than maximum, replace the armature.

      Fig 9: Measuring Commutator Length
      G03094995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. INSPECT STARTER COMMUTATOR END FRAME ASSY 
    1. Using vernier calipers, measure the brush length.
      • Standard length: 9.0 mm (0.354 in.) 
      • Maximum length: 4.0 mm (0.158 in.) 

      If the length is less than minimum, replace the starter assy.

      Fig 10: Measuring Brush Length
      G03094996Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the brush holder.
      1. Using an ohmmeter, check that there is no continuity between the positive (+) and negative (-) brushes.

      If there is continuity, repair or replace the starter assy.

      Fig 11: Checking For No Continuity Between Positive (+) And Negative (-) Brushes
      G03094997Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSY 
    1. Check the gear teeth on the planetary gear, internal gear and starter clutch for wear or damage.

      If damaged, replace the gear or clutch assembly. Also check the drive plate ring gear for wear or damage.

    2. Inspect the starter clutch.
      1. Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.

      If necessary, replace the center bearing clutch sub-assy.

      Fig 12: Checking Clutch Pinion Gear Rotation
      G03094998Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. INSPECT REPAIR SERVICE STARTER KIT 
    1. Check the operation.
      1. Push in the plunger, then check that it returns quickly to its original position.

      If necessary, replace the starter assy.

      Fig 13: Checking Plunger Returns Quickly When Pushing Plunger In
      G03094999Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the pull-in coil for open circuit.
      1. Using an ohmmeter, check that there is continuity between terminals 50 and C.

      If there is no continuity, replace the starter assy.

      Fig 14: Checking Continuity Between Terminals 50 And C
      G03095000Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Check the continuity.
      1. Using an ohmmeter, check that there is continuity between terminal 50 and the switch body.

      If there is no continuity, replace the starter assy.

      Fig 15: Checking Continuity Between Terminal 50 And Switch Body
      G03095001Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSY 
    1. Install the drive lever set pin onto the starter center bearing clutch.
    2. Install the starter center bearing clutch with drive lever set pin to the starter drive housing.
      Fig 16: Installing Starter Center Bearing Clutch Sub-Assy
      G03095002Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. INSTALL PLANETARY GEAR 
    1. Apply grease to the planetary gears and planetary shaft pins.
    2. Install the 3 planet gears.
      Fig 17: Installing Planetary Gear
      G03095003Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL STARTER ARMATURE PLATE 
    1. Insert the starter armature plate into the starter yoke assy.
    2. Align the cutout of the plate with the inside protrusion of the starter yoke, and install the plate.
      Fig 18: Installing Starter Armature Plate
      G03095004Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. INSTALL STARTER ARMATURE ASSY 
    1. Apply grease to the washer plate and armature shaft.
    2. Install the armature shaft onto the starter commutator end frame assy.
    3. Using snap ring pliers, install the plate washer and snap ring.
      Fig 19: Installing Plate Washer And Snap Ring
      G03095005Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using vernier calipers, measure the snap ring length.

      Maximum length: 5.0 mm (0.197 in.) 

      If the length is greater than maximum, replace it with a new snap ring.

      Fig 20: Measuring Snap Ring Length
      G03095006Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. INSTALL STARTER COMMUTATOR END FRAME COVER 
  16. INSTALL STARTER YOKE ASSY 
    1. Align the starter commutator rubber end frame with the cutout of the starter yoke.
    2. Install the starter yoke assy onto the starter commutator end frame.
      Fig 21: Installing Starter Yoke Assy Onto Starter Commutator End Frame
      G03095007Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. INSTALL STARTER COMMUTATOR END FRAME ASSY 
    1. Align the key located on the starter yoke assy with the keyway of the starter housing.
      Fig 22: Aligning Key Located On Starter Yoke Assy With Keyway Of Starter Housing
      G03095008Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the starter yoke assy with the 2 through bolts.

      Torque: 6.0 N.m (61 kgf.cm, 53 in.lbf) 

      Fig 23: Identifying Starter Yoke Assy Through Bolts
      G03095009Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  18. INSTALL MAGNET SWITCH BODY 
    1. Apply grease to the plunger and hook.
    2. Put the plunger hook of the magnet switch body on the drive lever.
    3. Install the plunger and return spring.
      Fig 24: Installing Plunger And Return Spring
      G03095010Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the magnet switch body with the 2 screws.

      Torque: 7.5 N.m (76 kgf.cm, 66 in.lbf) 

    5. Connect the lead wire to the terminal with the nut.

      Torque: 10 N.m (102 kgf.cm, 7.4 ft.lbf) 

      Fig 25: Connecting Lead Wire To Terminal With Nut
      G03095011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002