LEMON Manuals: Even more car manuals for everyone
Home >> Saturn >> 1993 >> SL >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> System >> EXPERTEC TSB (94-T-05)

EXPERTEC TSB (94-T-05)

Publication date: 1994-02-15
Reference number: 94-T-05

EXPERTEC TSB

EXPERTEC TSB

TECHNICAL SERVICE BULLETIN

Reference Number(s): 94-T-05, Date of Issue:  02/15/94

ENGINE STUMBLES RUNS ROUGH - OR SURGES DURING START

Model(s): 1991-94 Saturn SC2

Bulletin No.: Saturn 94-T-05

Date: 02/15/1994

BULLETIN ILLUSTRATION LIST

Fig 1: Graphic
GE00W010953

SUBJECT

Engine Stumbles, Runs Rough or Surges During Initial Start-SOHC (LKO) and DOHC (LLO) Engines (Clean Carbon Deposits From Intake Valves)

MODELS AFFECTED

1991-94 Saturns

SERVICE INFORMATION

Some customers may comment that the vehicle may stumble, run rough or surge on initial cold start.

CAUSE

The intake valves may accumulate carbon or fuel deposits due to driving schedules and/or using gasoline without proper fuel additives.

NOTE: Carbon deposits from oil can usually be removed with Saturn Top Engine Cleaner (P/N 21007128) or equivalent, using the procedure outlined in this bulletin. Fuel deposits most frequently occur on SOHC (LKO) engine intake valves and must be removed with Saturn Carbon Blaster SA9212NE (or equivalent carbon blaster tool). Chemical cleaners will not remove fuel deposits.

CORRECTION

Perform the following procedures to remove carbon and fuel deposit accumulation.

PROCEDURE: SOHC (LKO) ENGINES

NOTE: Prior to performing the following procedures on 1991-92 vehicles built before and including VIN NZ241997, refer to "Technical Information Bulletin 92-T-14A-Oil Consumption on DOHC Engines or Carbon Buildup On SOHC Engines (Replace Valve Stem Seals)" and follow the procedures listed in the bulletin.

SERVICE PROCEDURE

Chemical Valve Cleaning - SOHC (LKO) Engine

  1. Run engine until normal operating temperature is obtained.
  2. Turn ignition Off.
  3. Disable electronic ignition system by removing "DIS" fuse and remove air cleaner cover.
  4. Remove valve rocker arm cover and loosen intake valve rocker arm shaft to allow the intake valves to close.
  5. Pour half the contents of Saturn Top Engine Cleaner (P/N 21007128) or equivalent into the throttle body fuel injector assembly and let soak a minimum of four hours.
    NOTE: Spark plugs must be removed to prevent engine damage during cranking.
  6. Remove spark plugs and place rags in front of each spark plug hole.
    NOTE: Rocker arm tangs (slots) must be properly seated prior to tightening rocker arm shaft bolts or valve and piston damage will occur.
  7. Uniformly tighten intake valve rocker arm shaft and install valve rocker arm Cover.

    Torque: 25 N-m (19 lbs. ft.) - Rocker Arm Shaft

    30 N-m (22 lbs. ft.) - Rocker Arm Cover

    NOTE: Do not crank engine for longer then 15 seconds at one time or damage to the starter motor could result.
  8. Crank engine 15 seconds, wait one minute, than crank engine for another 15 seconds.
  9. Remove rags, and install spark plugs and "DIS" fuse.

    Torque: 27 N-m (20 lbs. ft.)

  10. Start engine and allow it to reach normal operating temperature.
  11. Connect PDT to vehicle and perform special test "MAX IAC. "Slowly pour remaining contents of the Saturn Top Engine Cleaner (P/N 21007128) or equivalent into the throttle body fuel injector assembly.
  12. Install air cleaner cover.

    If the condition still exists, the valves are most likely contaminated with fuel deposits and must be cleaned with the Saturn Carbon Blaster SA9212NE or an equivalent carbon blasting tool. For instructions, refer to "Engine Mechanical Service Manual."

DOHC (LLO) ENGINES

Only oil carbon deposits have been identified on the DOHC (LLO) engine valves and the following procedure must be used.

NOTE: Prior to performing the following procedure on 1991-1992 vehicles built before and including VIN NZ237382, refer to "Technical Information Bulletin 92-T-14A - Oil Consumption on DOHC Engines or Carbon Buildup On SOHC Engines (Replace Valve Stem Seals)" and follow the procedures listed in the bulletin.
  1. Remove front air inlet duct assembly.
  2. Run engine until normal operating temperature is obtained.
  3. While engine is running, remove positive crankcase ventilation (PCV) valve (also called the crankcase vent valve assembly) from grommet in camshaft cover assembly. Leave PCV valve attached to the vacuum line.
  4. Connect PDT to vehicle and perform special test "MAX IAC." Allow complete can of Saturn Top Engine Cleaner (P/N 21007128) or equivalent, to be slowly drawn into the engine through the PCV valve by dipping the PCV valve in and out of the Saturn top engine cleaner.
  5. Install front air inlet duct assembly and the PCV valve into the grommet in the camshaft cover assembly Verify that the condition has been repaired. If the condition still exists, refer to the appropriate service manual for diagnostic procedures.

PARTS REQUIREMENTS

21007128 Saturn Top Engine Cleaner

CLAIM INFORMATION

To receive credit for this repair, submit a claim through the Saturn Dealer System as follows:

WARRANTY INFORMATION

Case Type Description Labor Operation Code Time
VW Chemical Valve Cleaning-SOHC Engine T9659 1.3 hrs
VW Chemical Valve Cleaning-DOHC Engine T9659 0.8 hrs
VW Add if required: Clean (Carbon Blaster) Valves, Intake - SOHC Engine J0400 3.4 hrs