LEMON Manuals: Even more car manuals for everyone
Home >> Porsche >> 2005 >> Boxster Base, Standard >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Technical Service Bulletins >> Other Variant >> Memory Modules >> Pcm2.1 System - Complaints And Repairs (GROUP 9, NO. 2/05)

Pcm2.1 System - Complaints And Repairs (GROUP 9, NO. 2/05)

WARNING: This page is about the Boxster Base, Automatic, which is a different variant/trim than selected.
Publication date: 2005-08-11
Reference number: GROUP 9, NO. 2/05

PCM2.1 SYSTEM CONNECTION: COMPLAINTS AND REPAIR

PCM2.1 SYSTEM CONNECTION: COMPLAINTS AND REPAIR

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 9, NO. 2/05, Date of Issue:  May 05, 2006
PORSCHE: Boxster (987)/Boxster S (987) - as of 2005 up to 2008
GROUP: 9 - Electrical
PART IDENTIFIER: ENU 9110

MODEL YEAR

as of 2005 up to 2008 

Information 

This Technical Information replaces the TI dated August 11, 2005.

Changes  compared to the previous Technical Information:

PCM entire system

VEHICLE TYPE

Boxster (987)/Boxster S (987) 

Concerns

Porsche Communication Management 2.1 (PCM2.1) 

Situation

Defects in the PCM2.1 system connection. 

Below you will find information about causes and remedial measures for existing complaints in relation to system components in the PCM2.1 system connection.

The listing is sorted according to the system components and possible complaints. This is not a complete list of defects.

COMPLAINTS LIST

PCM entire system  The function "Switching PCM on/off" is faulty. => 1.1
  No sound output/missing ext. components. => 1.2
  Message: "PCM switch-off protection - overtemperature". => 1.3
  After starting PCM: Unintentional switch to another system source. => 1.4
  Faulty CD operation. => 1.5
PCM operator control unit  Right-hand control knob slips. => 2.1
  "Mute" function is deactivated. => 2.2
  Screen flickers, there are horizontal black and white stripes visible. => 2.3
  Screen shows black stripes. => 2.4
DVD navigation  No GPS reception. => 3.1
  No navigation announcement. => 3.2
  Message: "Insert navigation DVD". => 3.3
  Inaccurate vehicle location/representation on the map. => 3.4
  Roads, rivers, and woods are not displayed on the map. => 3.5
  Map display does not change, remains unchanged. => 3.6
  DVD drive switches off. => 3.7
  Message "Navigation not available". => 3.8
BOSE sound system  Playback volume changes in normal driving => 4.1
  Sound failure in sound system. => 4.2
  Mute when opening the convertible top. => 4.3
  Whistling noise from the rear left loudspeaker. => 4.4
  Coding for "left-hand drive" is not possible. => 4.5
Individual memory  Function sequences deviate from the personal settings. => 5.1
  ...cannot be adjusted. => 5.2
Multifunction steering wheel.  Functions of multifunction steering wheel buttons do not correspond to basic setting. => 6.1

Work Procedure

  1. PCM2.1 entire system 
    1. 1.1 The function "Switching PCM on/off" is faulty. 
      1. 1.1.1 When switching on the ignition, the PCM does not switch on; switching on is not possible even with the left rotary knob. 

        Cause 1:  When removing the ignition key, the PCM was switched off or when there was no ignition key inserted, the PCM was switched on and off.

        End  of remedial action.

        Cause 2:  PCM is still set to "Production mode -> ON".

        Remedial action: Change the coding in the menu "PCM2.1 GW -> Coding -> Production mode -> OFF" using the PIWIS Tester.

        End  of remedial action.

      2. 1.1.2 After switching on the ignition, the Porsche crest is displayed in the PCM, then the PCM switches off and cannot be switched on by pressing the left rotary knob. 

        Cause: PCM is still set to "Production mode -> ON".

        Remedial action: Change the coding in the menu "PCM2.1 GW -> Coding -> Production mode -> OFF" using the PIWIS Tester.

        End  of remedial action.

      3. 1.1.3 PCM does not function. 

        Cause 1  : PCM is still set to "Production mode -> ON".

        Remedial action: Change the coding in the menu "PCM2.1 GW -> Coding -> Production mode -> OFF" using the PIWIS Tester. If this is not  possible: => Cause 2 

        End  of remedial action.

        Cause 2:  PCM device fault.

        Remedial action: Replace PCM operator control unit.

        End  of remedial action.

      4. 1.1.4 PCM does not switch off automatically after removing the ignition key (-> increased closed-circuit current)  (only vehicles with "Sport Chrono Package").

        Cause: The function "Sport display" in the trip computer (TRIP) is still switched on. After removing the ignition key, the system remains in Standby mode for approx. 5 minutes so that time measurement can be continued.

        Remedial action: This is not a fault. Before  removing the ignition key, end the "Sport display" function.

        End  of remedial action.

      5. 1.1.5 A PCM switched on via the left control knob (ignition key is not in ignition lock) does not switch off immediately when locking the vehicle. 

        Cause: PCM switches off only after activation of anti-theft protection.

        Remedial action: This is not a fault.

        End  of remedial action.

    2. 1.2 No sound output and/or missing external components  (e.g. error message "CD changer not available").

      Cause 1  : MOST set point configuration is not coded in PCM.

      Remedial action: Select "PCM2.1 MMI -> Planned & Actual configuration" in the "PCM2.1" control unit using the PIWIS Tester and save this by pressing "F8".

      If this does not help: => Cause 2 

      End  of remedial action.

      Cause 2:  Component does not function.

      Remedial action: Select "PCM2.1 -> MOST component check -> MOST system check" using the PIWIS Tester. If this is not possible: Replace components. After replacing components, code them using the PIWIS Tester.

      End  of remedial action.

    3. 1.3 PCM switches off after you start the system and the message "PCM switch-off protection - over temperature" appears. 

      Cause: The navigation software "Model Level A"  (= Model Level A, DVD labelled 04.2004 or 08.2004 or 10.2004) was used previously to force or perform a Downdate  on a navigation unit, which is only compatible  with the "Model Level B"  software (= Model Level B, DVD labelled 04.2005 or higher).

      Remedial action: Perform a forced update using the Model Level B  DVD.

      To do this, insert the DVD into the navigation unit and switch off PCM. Then interrupt the power supply (terminal 30) via fuse 9  (right side of dashboard) for at least 60 seconds.  The navigation update is performed automatically when you insert the fuse and switch on PCM.

      See also → 911200 PCM 2.1 and navigation unit: Connection release for model care B  (No. 7/05).

      End  of remedial action.

    4. 1.4 After starting PCM: Unintentional switch to another system source  , (e.g. when a CD is inserted while Tuner mode is on, the system switches automatically to the CD drive when PCM is started even though the tuner is activated).

      Cause: Software error. This relates to PCM with connection release version Standard or Model Level A  (Model Level A).

      Remedial action: Perform update using new  Model Level A CD, => 000.043.205.46.004  PCM2 Update CD-ROM.

      End  of remedial action.

    5. 1.5 Faulty CD operation. 
      1. 1.5.1 Sound comes and goes at low temperatures after starting PCM. 

        Cause: Software error in CD drive.

        Remedial action: Install new software.

        Perform installation according to => Technical Information 'W61000 Workshop campaign W610 - Installing new system software on the PCM2.1' (No. 18/05).

        End  of remedial action.

      2. 1.5.2 
        • Defective CD playback function or CD will not play, 
        • MP3 or WMA capability does not function. 

        Cause: Component tolerances in the CD drive.

        Remedial action: Install new software.

        Perform installation according to => Technical Information 'W61000 Workshop campaign W610 - Installing new system software on the PCM2.1' (No. 18/05).

        End  of remedial action.

      3. 1.5.3 CD is not automatically inserted or ejected. 

        Cause: Component tolerances in the CD drive.

        Remedial action: Replace PCM control module; for more information, see:  → 911000 Spare parts requirements for PCM2.1 operator control unit. Model care B  (No. 20/05).

        End  of remedial action.

  2. PCM2.1 operator control unit 
    1. 2.1 Control knob: right-hand rotary knob slips. 

      Cause: Reduced contact force due to temperature effect and control module tolerances.

      Remedial action: Fit a new rotary knob, => 997.642.202.00.A05; see also → 911000 PCM2.1 Right-hand control knob slips  (997, No. 6/04).

      End  of remedial action.

    2. 2.2 "Mute" function is automatically deactivated. 

      Cause: The mute set is cancelled when the set volume is modified using the PCM control knob or on the multifunction steering wheel. This also happens if the volume was adjusted during a phone call or a navigation announcement.

      Remedial action: This is not a fault.

      End  of remedial action.

    3. 2.3 Screen flickers, there are horizontal black and white stripes visible. 

      Cause: PCM device fault.

      Remedial action: Replace PCM operator control unit.

      End  of remedial action.

    4. 2.4 Screen shows black stripes. 

      Cause: PCM device fault.

      Remedial action: Replace PCM operator control unit.

      End  of remedial action.

  3. DVD navigation 
    1. 3.1 No GPS reception 

      Cause 1:  Antenna not installed, faulty, not plugged in and/or plug connection is loose.

      Remedial action: Read out the fault memory in the "Navigation" menu in the "PCM2.1" control unit with the PIWIS Tester. If no faults are stored in the fault memory:

      => Cause 2 

      Work through the fault codes in the memory according to => Diagnosis '91 PCM2 Navigation', see also → 911319 Removing and installing GPS antenna. 

      End  of remedial action.

      Cause 2:  Antenna lead and/or GPS antenna and/or navigation unit does not function.

      Remedial action:

      1. - Park the vehicle in a wide open space. Connect the PIWIS Tester, select the GPS item in the "Navigation -> Special functions" menu and read out the number of satellites received. To get comparable values: -> Park another vehicle in the same spot and read out the number of satellites received for this.
      2. - If the number of satellites in the queried vehicle = 0 and the number in the comparison vehicle is greater or equal to 3: -> check the plug connections of the antenna lead for corrosion and secure fit. If corrosion is found, replace the antenna lead and/or the booster.
      3. - After you have done this, compare receivable satellites again. If the number of satellites in the queried vehicle = 0 and the number in the comparison vehicle is greater or equal to 3: -> Remove navigation unit and install it in the comparison vehicle to test the GPS reception. 
      4. - If GPS is received in the comparison vehicle (= number of satellites is greater or equal to 3): -> replace GPS antenna  in the queried vehicle. If GPS reception is not possible: -> replace the navigation unit. 

        End  of remedial action.

    2. 3.2 Navigation announcement: No announcement after pressing the "Repeat" button. 

      Cause: In navigation set (NAVI set), the volume for "Navigation" is set to "OFF" or very quiet.

      Remedial action: In NAVI set, change the volume setting or increase the volume after pressing the "Repeat" button.

      End  of remedial action.

    3. 3.3 "Please insert Navigations DVD" navigation message. 
      1. 3.3.1 ... after pressing the "NAVI" button. 

        Cause 1:  No DVD in the navigation unit.

        If this is not the case: => Cause 2 

        Remedial action: Put DVD in the navigation unit.

        End  of remedial action.

        Cause 2:  DVD is inserted on the wrong side (printed side downward).

        If this is not the case: => Cause 3 

        Remedial action: Insert DVD correctly (printed side upward).

        End  of remedial action.

        Cause 3:  Navigation DVD  is inserted in CD  slot of operator control unit.

        If this is not the case: => Cause 4 

        Remedial action: Put DVD in the navigation unit.

        End  of remedial action.

        Cause 4:  DVD drive was switched off automatically because of overheating.

        Remedial action: Check which DVD version is inserted in the drive (the version number is shown on the DVD):

        -> If version 08.2004 or higher  is inserted: this is not a fault. The drive was switched off because of overheating.

        -> If version 04.2004  is inserted: => Remedial action 3.7

        End  of remedial action.

      2. 3.3.2 ... during operation of the navigation system. 

        Cause: Problem when reading data. The DVD may be dirty, scratched, or damp, the reading head may be dirty or faulty.

        Remedial action Check DVD for damage or clean with soft, clean cloth.

        1:  Switch navigation system off and then on again.

        If the problem persists: => Remedial action 2 

        Remedial action Replace DVD.

        2:  If the problem persists: => Remedial action 3 

        Remedial action Replace navigation unit.

        3: End  of remedial action.

    4. 3.4 Inaccurate vehicle location and representation on the map. 
      1. 3.4.1 Imprecise position of vehicle symbol (triangular arrow) in the map display (e.g. arrow is displayed on the left or right of street being travelled). 

        Cause 1:  Result of multiple digitalisation faults on the previously travelled stretch.

        Remedial action: This is not a fault.

        End  of remedial action.

        Cause 2:  A tire was changed on the front and/or rear axle.

        Remedial action: This is not a fault. In menu "NAVI-Set", activate the menu item "Tire change". After changing the tire, fine calibration can be attained only after a journey of 30 miles (50 km).

        End  of remedial action.

      2. 3.4.2 Sporadic failure of vehicle symbol or failure always at the same geographical position. 

        Cause 1:  Temporary "loss of locating signal" of navigation system.

        Remedial action: This is not a fault.

        End  of remedial action.

        Cause 2:  Imprecise or too little data in database, thus exact calculations are not possible.

        Remedial action: This is not a fault.

        End  of remedial action.

    5. 3.5 Roads, rivers, and woods are not displayed in the map display. 

      Cause: Problem when reading data. The DVD may be dirty, scratched, or damp, the reading head may be dirty or faulty.

      Remedial action: => 3.3.2 

      End  of remedial action.

    6. 3.6 Map display does not change, remains unchanged. 
      1. 3.6.1 ... and vehicle symbol moves out of the map view. 

        Cause 1:  "Cross zoom" is activated. Map display activation is delayed due to high PCM computer load (due to new route calculation).

        Remedial action: This is not a fault. Is possible when longer routes are calculated and the driver deviates from the route. The route calculation has priority over the map display.

        If this is not the case: => Cause 2 

        End  of remedial action.

        Cause 2:  Screen displays "Map set" at lower left. The map options "Location" or "Destination" of map menu are deactivated.

        If this is not the case: => Cause 3 

        Remedial action: Activate "Location" in map menu over the right control knob.

        End  of remedial action.

        Cause 3:  Problem when reading data. The DVD may be dirty, scratched, or damp, the reading head may be dirty or faulty.

        Remedial action: => 3.3.2 

        End  of remedial action.

      2. 3.6.2 ... and vehicle symbol does not move from position. 

        Cause 1:  Software error. No reception of vehicle wheel pulses in navigation system.

        Remedial action: Replace the previously used DVD by DVD, version 10.2004, and update the PCM2, → 911000 Spare parts requirements PCM2.1 and/or BOSE amplifier  (No. 1/04)

        End  of remedial action.

      3. 3.6.3 ... after starting the navigation system. 

        Cause 1:  Problem when reading data. The DVD may be dirty, scratched, or damp, the reading head may be dirty or faulty.

        Remedial action: => 3.3.2 

        End  of remedial action.

    7. 3.7 Navigation unit switches DVD drive off (switch off protection). 

      Longer Stop/Go driving at higher outside temperatures (>86°F/30°C) and direct sun radiation can cause the message "Switch off protection of DVD drive temperature" with simultaneous switch-off of DVD drive. After cooling phase of drive (approx. 10 min) the route is calculated again, the screen display is complete again.

      Cause: Software error. Switch-off protection of navigation unit triggers too soon.

      Remedial action: Install software with modified switch-off protection. To do this, replace the previously used DVD with the version 08.2004 DVD, => 997.642.235.03.

      See also → 911200 PCM2.1: DVD navigation unit switches off automatically  (No. 11/04).

      End  of remedial action.

    8. 3.8 "Navigation not available"  message appears after starting the system at low temperatures (approx. 32°F/0°C or lower).

      Cause: Hardware fault. This relates to navigation units with PCM2.1 connection release version Standard or Model Level A  with serial numbers from 4750 7869 to 4755 7424. 

      Remedial action: Replace navigation unit. Observe the serial numbers specified above when replacing equipment.

      When the navigation unit is installed, you can look up the serial number in a printable diagnostic working log.

      End  of remedial action.

  4. BOSE sound system 
    1. 4.1 Playback volume changes during normal driving 

      Cause: "AudioPilot" function is activated in "Adjust sound/surround" menu.

      Remedial action: This is not a fault.

      End  of remedial action.

    2. 4.2 Sound failure in sound system. 

      Cause: Software error in BOSE amplifier.

      Remedial action 1:  Update BOSE amplifier. For information on how to do this, see → 911000 BOSE sound package: Sound failure  (No. 8/04).

      If this does not help: => Remedial action 2 

      End  of remedial action.

      Remedial action 2: Replace BOSE amplifier.

      End  of remedial action.

    3. 4.3 When opening the convertible top, the BOSE sound system is mute for approx. 0.3 seconds. 

      Cause: During Open convertible top, the sound parameters of the sound system are adapted. This causes a mute for approx. 0.3 seconds.

      Remedial action: This is not a fault.

      End  of remedial action.

    4. 4.4 Coding: BOSE amplifier cannot be coded to "left-hand drive". 

      Cause: Amplifiers are coded "left-hand drive" ex works.

      Remedial action: Coding changed as of PIWIS software version 8.0.

      End  of remedial action.

      Work Procedure:

  5. Individual memory 
    1. 5.1 Function sequences deviate from the personal settings or are erratic. 

      Cause: On the customer side, either the individual memory was reset to "Factory settings" or a vehicle key is used which is not stored in memory (max. 3 possible).

      Remedial action: This is not a fault.

      End  of remedial action.

    2. 5.2 ... cannot be adjusted/changed  (menu item is greyed out).

      Cause 1:  Ignition is switched off.

      Remedial action: Switch on ignition.

      End  of remedial action.

      Cause 2  : Vehicle key used is not stored in memory (max. 3 vehicle keys possible).

      Remedial action: Use one of the stored vehicle keys.

      End  of remedial action.

      Work Procedure:

  6. Multifunction steering wheel  (buttons)
    1. 6.1 Functions of multifunction steering wheel buttons and knobs do not correspond to basic setting  (e.g. right-hand knob starts station-search function instead of list selection).

      Cause: PCM was replaced and/or coded using tester software that is no longer valid.

      Remedial action: Change the basic setting in the menu "PCM2.1 MMI -> Coding -> Multifunction steering wheel -> Write default values" in the "PCM2.1" control unit using the PIWIS Tester and software version 10.0 (or higher).

      End  of remedial action.

References

→ 911000 Spare parts requirements for PCM2.1 and/or BOSE amplifier  (No. 1/04)

→ 911000 PCM2.1 Right-hand control knob slips  (997, No. 6/04)

→ 911000 BOSE sound package: Sound failure  (No. 8/04)

→ 911200 PCM2.1: DVD navigation unit switches off automatically  (No. 11/04)

→ 911200 PCM2.1 and navigation unit: Connection release for model care B  (No. 7/05)

=> Technical Information 'W61000 Workshop campaign W610 - Installing new system software on the PCM2.1' (No. 18/05)

=> 911000 Spare parts requirements for PCM2.1 operator control unit, Model care B  (No. 20/05)

=> Diagnosis '91 PCM2 Navigation'

→ 911319 Removing and installing GPS antenna