LEMON Manuals: Even more car manuals for everyone
Home >> Pontiac >> 2005 >> GTO Standard >> Repair and Diagnosis >> Electrical >> Charging Systems >> Battery, Charging System And Starting System >> Diagnostic Information and Procedures >> Battery Electrical Drain/Parasitic Load Test >> Test Procedure

Test Procedure

    CAUTION: Refer to Battery Disconnect Caution in Cautions and Notices.
  1. Disconnect the battery negative cable from the battery negative terminal.
  2. Install the male end of the J 38758  to the battery ground terminal. See Special Tools .
  3. Turn the J 38758  knob (1) to the OFF position.
  4. Install the battery negative cable to the female end of the J 38758  .
  5. Turn the J 38758  knob to the ON position.
  6. Road test the vehicle and activate all of the accessories, including the radio and the air conditioning.
  7. Park the vehicle. Turn the ignition switch to the OFF position and remove the ignition switch key.
  8. Fig 1: Connecting Fuse Jumper Wire To Test Switch
    GM405487Courtesy of GENERAL MOTORS CORP.
  9. Connect a 10 A fused jumper wire to the test switch tool terminals (1).
  10. Turn the J 38758  knob to the OFF position. The current flows through the jumper wire.
  11. Wait 1 minute. If the fuse blows use an inductive ammeter to locate the current draw.
  12. Set a digital multimeter to the 10 A scale.
  13. Fig 2: Connecting Digital Multimeter To Test Switch
    GM405490Courtesy of GENERAL MOTORS CORP.
  14. Connect the digital multimeter to the test switch tool terminals (1).
  15. Turn the J 38758  knob to the OFF position. The current flows through the digital multimeter.
  16. Wait 1 minute. Check and record the current reading.
    1. When there is a current reading of 2 A or less, turn the J 38758  knob to the ON position. The electrical current will now pass through the switch.
    2. Then, switch the digital multimeter down to the 2 A scale for a more accurate reading when the J 38758  knob is turned OFF.
  17. Turn the J 38758  knob to the OFF position. Wait 10 minutes.
  18. Check and record the current reading.
  19. Note the battery reserve capacity. Refer to Battery Usage .
    1. Divide the reserve capacity by 4.
    2. Compare this to the multimeter milliampere reading taken in the previous step.

      The parasitic current drain should not exceed this number.

      Example: If a battery has a reserve capacity of 100 minutes, the current drain should not exceed 25 mA.

  20. Check the charging system if the vehicle has an acceptable amount of current drain. Refer to Charging System Test .
  21. NOTE: The test switch must be in the ON position when removing the fuses in order to maintain continuity in the electrical system. This avoids damaging the digital multimeter due to accidental overloading, such as a door being opened to change a fuse.
  22. When the vehicle has an unacceptable amount of parasitic current drain, remove each fuse one at a time until the current drain falls to an acceptable level. This will indicate which circuit is causing the drain. Refer to Power Distribution Schematics in Wiring Systems to diagnose exactly which part of the suspect circuit is causing the parasitic drain. In some cases a non-fused circuit or component, such as a generator, is the cause of excessive parasitic current drain.
  23. Repeat the parasitic current drain test procedure after any repair has been completed to make sure that the parasitic current drain is at an acceptable level.
  24. When the cause of the excessive current draw has been located and repaired, remove the J 38758  .
  25. NOTE: Refer to Fastener Notice in Cautions and Notices.
  26. Connect the battery negative cable to the battery negative terminal.

    Tighten:  Tighten the negative battery cable terminal bolt to 17 N.m (13 lb ft).