LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2017 >> Quest SL >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System (Introduction, Wiring Diagrams And Basic Inspection) >> Ecu Diagnosis Information >> ECM >> Reference Value >> Values On The Diagnosis Tool

Values On The Diagnosis Tool

NOTE:
  • The following table includes information (items) inapplicable to this vehicle. For information (items) applicable to this vehicle, refer to CONSULT display items.
  • Numerical values in the following table are reference values.
  • These values are input/output values that ECM receives/transmits and may differ from actual operations.

Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the data monitor. This occurs because the timing light shows a value calculated by ECM according to signals received from the cam shaft position sensor and other sensors related to ignition timing.

For outlines of following items, refer to CONSULT FUNCTION .

Monitor Item Condition Values/Status
ENG SPEED Run engine and compare CONSULT value with the tachometer indication. Almost the same speed as the tachometer indication.
MASS AIR FLOW SENSOR (Hz) See DESCRIPTION .
B/FUEL SCHDL See DESCRIPTION .
A/F ALPHA-B1 See DESCRIPTION .
A/F ALPHA-B2 See DESCRIPTION .
COOLANT TEMP/S
  • Engine: After warming up
More than 70°C (158°F)
A/F SEN1 (B1)
  • Engine: After warming up
Maintaining engine speed at 2, 000 RPM Fluctuates around 2.2 V
A/F SEN1 (B2)
  • Engine: After warming up
Maintaining engine speed at 2, 000 RPM Fluctuates around 2.2 V
HO2S2 (B1)
  • Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
    • Engine: After warming up
    • After keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
0 - 0.3 V ←→ Approx. 0.6 - 1.0 V
HO2S2 (B2)
  • Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
    • Engine: After warming up
    • After keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
0 - 0.3 V ←→ Approx. 0.6 - 1.0 V
HO2S2 MNTR (B1)
  • Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
    • Engine: After warming up
    • After keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
LEAN ←→ RICH
HO2S2 MNTR (B2)
  • Revving engine from idle to 3, 000 RPM quickly after the following conditions are met.
    • Engine: After warming up
    • After keeping engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
LEAN ←→ RICH
VHCL SPEED SE
  • Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as speedometer indication
BATTERY VOLT
  • Ignition switch: ON (Engine stopped)
11 - 14 V
ACCEL SEN 1
  • Ignition switch: ON

    (Engine stopped)

Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
ACCEL SEN 2*1
  • Ignition switch: ON

    (Engine stopped)

Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
TP SEN 1-B1
  • Ignition switch: ON

    (Engine stopped)

  • Selector lever: D position
Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*1
  • Ignition switch: ON

    (Engine stopped)

  • Selector lever: D position
Accelerator pedal: Fully released More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE
  • Ignition switch: ON
Indicates fuel tank temperature
INT/A TEMP SE
  • Ignition switch: ON
Indicates intake air temperature
EVAP SYS PRES
  • Ignition switch: ON
Approx. 1.8 - 4.8 V
FUEL LEVEL SE
  • Ignition switch: ON
Depending on fuel level of fuel tank
START SIGNAL
  • Ignition switch: ON → START → ON
OFF → ON → OFF
CLSD THL POS
  • Ignition switch: ON

    (Engine stopped)

Accelerator pedal: Fully released ON
Accelerator pedal: Slightly depressed OFF
AIR COND SIG
  • Engine: After warming up, idle the engine
Air conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates.)
ON
P/N POSI SW
  • Ignition switch: ON
Selector lever: P or N position ON
Selector lever: Except above position OFF
PW/ST SIGNAL
  • Engine: After warming up, idle the engine
Steering wheel: Not being turned OFF
Steering wheel: Being turned ON
LOAD SIGNAL
  • Ignition switch: ON
Rear window defogger switch: ON
and/or
Lighting switch: 2nd position
ON
Rear window defogger switch and lighting switch: OFF OFF
IGNITION SW
  • Ignition switch: ON → OFF → ON
ON → OFF → ON
HEATER FAN SW
  • Engine: After warming up, idle the engine
Heater fan switch: ON ON
Heater fan switch: OFF OFF
BRAKE SW
  • Ignition switch: ON
Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
INJ PULSE-B1
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 2.0 - 3.0 msec
2, 000 RPM 1.9 - 2.9 msec
INJ PULSE-B2
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 2.0 - 3.0 msec
2, 000 RPM 1.9 - 2.9 msec
IGN TIMING
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 7 - 17° BTDC
2, 000 RPM 25 - 45° BTDC
CAL/LD VALUE
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 5 - 35%
2, 500 RPM 5 - 35%
MASS AIRFLOW
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 2.0 - 6.0 g/s
2, 500 RPM 7.0 - 20.0 g/s
PURG VOL C/V
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle
(Accelerator pedal: Not depressed even slightly, after engine starting.)
0%
2, 000 RPM -
INT/V TIM (B1)
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle - 5 - 5°CA
2, 000 RPM Approx. 0 - 30°CA
INT/V TIM (B2)
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle - 5 - 5°CA
2, 000 RPM Approx. 0 - 30°CA
INT/V SOL (B1)
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 0 - 2%
2, 000 RPM Approx. 0 - 50%
INT/V SOL (B2)
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 0 - 2%
2, 000 RPM Approx. 0 - 50%
VIAS S/V-1
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
When revving engine up to 5, 000 RPM quickly OFF →ON → OFF
VIAS S/V-2
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
When revving engine up to 5, 000 RPM quickly OFF →ON → OFF
AIR COND RLY
  • Engine: After warming up, idle the engine
Air conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates)
ON
ENGINE MOUNT
  • Engine: After warming up
Below 950 RPM IDLE
Above 950 RPM TRVL
FUEL PUMP RLY
  • For 1 second after turning ignition switch: ON
  • Engine running or cranking
ON
  • Except above
OFF
VENT CONT/V
  • Ignition switch: ON
OFF
THRTL RELAY
  • Ignition switch: ON
ON
COOLING FAN
  • Engine: After warming up, idle the engine
  • Air conditioner switch: OFF
Engine coolant temperature: 97°C (206°F) or less OFF
Engine coolant temperature: Between 98°C (208°F) and 99°C (210°F) LOW
Engine coolant temperature: Between 100°C (212°F) and 104°C (219°F) MID
Engine coolant temperature: 105°C (221°F) or more HI
HO2S2 HTR (B1)
  • Engine speed: Below 3, 600 RPM after the following conditions are met.
    • Engine: After warming up
    • Keeping the engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
ON
  • Engine speed: Above 3, 600 RPM
OFF
HO2S2 HTR (B2)
  • Engine speed: Below 3, 600 RPM after the following conditions are met.
    • Engine: After warming up
    • Keeping the engine speed between 3, 500 and 4, 000 RPM for 1 minute and at idle for 1 minute under no load
ON
  • Engine speed: Above 3, 600 RPM
OFF
I/P PULLY SPD
  • Vehicle speed: More than 20 km/h (12 MPH)
Almost the same speed as the tachometer indication
VEHICLE SPEED
  • Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as the speedometer indication
IDL A/V LEARN
  • Engine: Running
Idle air volume learning has not been performed yet. YET
Idle air volume learning has already been performed successfully. CMPLT
ENG OIL TEMP
  • Engine: After warming up
More than 70°C (158°F)
TRVL AFTER MIL
  • Ignition switch: ON
Vehicle has traveled after MIL has illuminated. 0 - 65, 535 km
(0 - 40, 723 miles)
A/F S1 HTR (B1)
  • Engine: After warming up, idle the engine

    (More than 140 seconds after starting engine)

4 - 100%
A/F S1 HTR (B2)
  • Engine: After warming up, idle the engine

    (More than 140 seconds after starting engine)

4 - 100%
AC PRESS SEN
  • Engine: Idle
  • Both A/C switch and blower fan switch: ON (Compressor operates)
1.0 - 4.0 V
VHCL SPEED SE
  • Turn drive wheels and compare CONSULT value with the speedometer indication.
Almost the same speed as the speedometer indication
SET VHCL SPD
  • Engine: Running
ASCD: Operating The preset vehicle speed is displayed
MAIN SW
  • Ignition switch: ON
MAIN switch: Pressed ON
MAIN switch: Released OFF
CANCEL SW
  • Ignition switch: ON
CANCEL switch: Pressed ON
CANCEL switch: Released OFF
RESUME/ACC SW
  • Ignition switch: ON
RESUME/ACCELERATE switch: Pressed ON
RESUME/ACCELERATE switch: Released OFF
SET SW
  • Ignition switch: ON
SET/COAST switch: Pressed ON
SET/COAST switch: Released OFF
BRAKE SW1
(Brake pedal position switch)
  • Ignition switch: ON
Brake pedal: Fully released ON
Brake pedal: Slightly depressed OFF
BRAKE SW2
(Stop lamp switch)
  • Ignition switch: ON
Brake pedal: Fully released OFF
Brake pedal: Slightly depressed ON
VHCL SPD CUT
  • Ignition switch: ON
NON
LO SPEED CUT
  • Ignition switch: ON
NON
AT OD MONITOR
  • Ignition switch: ON
OFF
AT OD CANCEL
  • Ignition switch: ON
OFF
CRUISE LAMP
  • Ignition switch: ON
MAIN switch: Pressed at the 1st time → at the 2nd time ON → OFF
SET LAMP
  • MAIN switch: ON
  • When vehicle speed is between 40 km/h (25 MPH) and 144 km/h (89 MPH)
ASCD: Operating ON
ASCD: Not operating OFF
ALT DUTY
  • Engine: Idle
0 - 80%
A/F ADJ-B1
  • Engine: Running
- 0.330 - 0.330
A/F ADJ-B2
  • Engine: Running
- 0.330 - 0.330
BAT CUR SEN
  • Engine speed: Idle
  • Battery: Fully charged * 2
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Approx. 2, 600 - 3, 500 mV
ALT DUTY SIG
  • Power generation voltage variable control: Operating
ON
  • Power generation voltage variable control: Not operating
OFF
EVAP LEAK DIAG Ignition switch: ON Indicates the condition of EVAP leak diagnosis.
EVAP DIAG READY Ignition switch: ON Indicates the ready condition of EVAP leak diagnosis.
HO2 S2 DIAG1 (B1) DTC P0139 self - diagnosis (delayed response) is incomplete. INCMP
DTC P0139 self - diagnosis (delayed response) is complete. CMPLT
HO2 S2 DIAG1 (B2) DTC P0159 self - diagnosis (delayed response) is incomplete. INCMP
DTC P0159 self - diagnosis (delayed response) is complete. CMPLT
HO2 S2 DIAG2 (B1) DTC P0139 self - diagnosis (slow response) is incomplete. INCMP
DTC P0139 self - diagnosis (slow response) is complete. CMPLT
HO2 S2 DIAG2 (B2) DTC P0159 self - diagnosis (slow response) is incomplete. INCMP
DTC P0159 self - diagnosis (slow response) is complete. CMPLT
THRTL STK CNT B1* 3 - -
BAT TEMP SEN
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle Indicates the temperature around the battery.
FUEL PUMP DUTY
  • Engine: After warming up
  • Selector lever: P or N position
  • Air conditioner switch: OFF
  • No load
Idle 30 - 40%
EOP SENSOR
  • Engine: After warming up
  • Selector lever: P or N
  • Air conditioner switch: OFF
  • No load
Idle Approx. 1.45 V
2, 000 RPM Approx. 2.85 V
VTC DTY EX B1* 3 - -
VTC DTY EX B2* 3 - -
A/F-S ATMSPHRC CRCT B1 Engine: After warming up, idle the engine Varies depending on vehicle environment.
A/F-S ATMSPHRC CRCT B2 Engine: After warming up, idle the engine Varies depending on vehicle environment.
A/F-S ATMSPHRC CRCT UP B1 Engine: Running Varies depending on the number of updates.
SYSTEM 1 DIAGNOSIS A B1 DTC P219A self-diagnosis is incomplete. INCMP
DTC P219A self-diagnosis is incomplete. CMPLT
SYSTEM 1 DIAGNOSIS A B2 DTC P219B self-diagnosis is incomplete. INCMP
DTC P219B self-diagnosis is incomplete. CMPLT
SYSTEM 1 DIAGNOSIS B B1 DTC P219A self-diagnosis is on standby. ABSENT
DTC P219A self-diagnosis is under diagnosis. PRSENT
SYSTEM 1 DIAGNOSIS B B2 DTC P219B self-diagnosis is on standby. ABSENT
DTC P219B self-diagnosis is under diagnosis. PRSENT
A/F-S ATMSPHRC CRCT UP B2 Engine: Running Varies depending on the number of updates.

* 1: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Thus, they differ from ECM terminals voltage signal.

* 2: Before measuring the terminal voltage, confirm that the battery is fully charged. Refer to HOW TO HANDLE BATTERY .

* 3: The item is indicated, but not used.