LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2015 >> Versa SL >> Repair and Diagnosis >> Body & Frame >> Seats >> Unit Disassembly And Assembly >> Front Seat >> Driver Side >> Disassembly And Assembly >> Disassembly

Disassembly And Assembly: Disassembly

  1. Remove the front seat assembly. Refer to REMOVAL AND INSTALLATION .
  2. Release the lower seatback trim retainer strap (A) from the seat cushion frame.
    Fig 1: Locating Lower Seatback Trim Retainer Strap
    G08203936Courtesy of NISSAN NORTH AMERICA, INC.
  3. Remove the armrest (1) (if equipped).
    Fig 2: Removing Armrest Bolt And Armrest
    G09015323Courtesy of NISSAN NORTH AMERICA, INC.
    1. Unzip the armrest to access the armrest bolt (A).
    2. Remove the armrest bolt (A) and the armrest (1).
  4. Release the J-hook retainer (C), unzip seatback zipper (A) and release J-clips (B) holding the seatback trim to the seat frame assembly.
    Fig 3: Identifying J-Hook Retainer, Unzip Seatback Zipper And Release J-Clips
    G09015324Courtesy of NISSAN NORTH AMERICA, INC.
  5. Reach up through the seatback trim and release locks as shown below and remove the headrest holders (if equipped).
    Fig 4: Removing Headrest Holder
    G04146145Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Before removing/installing the headrest holder, check its orientation (front/rear and right/left)

  6. Remove and discard the two chute rod nuts (B), then route the chute rod (1) through the opening and remove it from the chute (A).
    Fig 5: Removing Chute Rod
    G09015326Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Do not reuse the chute rod nuts.

  7. Release the side air bag module harness from the seat frame assembly.
    Fig 6: Locating Side Air Bag Module Harness Clips
    G08203943Courtesy of NISSAN NORTH AMERICA, INC.
    NOTE:

    Take note of harness routing and attachment location for accurate installation.

    1. From the back of the seat unclip the side air bag module harness clips (ARROWF ).
    2. From the bottom of the seat unclip the side air bag module harness clips (ARROWF ).
      Fig 7: Locating Side Air Bag Module Harness Clips
      G08203940Courtesy of NISSAN NORTH AMERICA, INC.
  8. Remove and discard the two side air bag module nuts (A).
    Fig 8: Removing Side Air Bag Module Nuts
    G09015329Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:

    Do not reuse the side air bag module nuts.

  9. Release the side air bag module studs from the seatback frame and lift the seatback trim and seatback pad as an assembly from the seat frame assembly.
  10. Pull the side air bag module (1) out of the chute (A) and remove from the seatback trim.
    Fig 9: Locating Side Air Bag Module And Chute
    G09015330Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • Replace the side air bag module if it has been dropped or sustained an impact.
      Fig 10: Precaution For Handling Air Bag Module
      G05224522Courtesy of NISSAN NORTH AMERICA, INC.
    • Do not strike the side air bag module.
  11. Separate the seatback trim from the seatback pad.
    1. For seatback with removable headrest.
      Fig 11: Locating Hog Rings And Separate The Seatback Trim (1)
      GNSALJIA0988ZZ-988Courtesy of NISSAN NORTH AMERICA, INC.
      1. Remove the hog rings and separate the seatback trim (1) from the seatback pad.

        SHIKAKU-H : Hog ring

        NOTE:

        Remove all pieces of hog rings and discard them.

    2. For seatback without removable headrest.
      Fig 12: Locating Seatback Trim With Hog Rings
      G09015333Courtesy of NISSAN NORTH AMERICA, INC.
      1. Remove the hog rings and separate the seatback trim (1) from the seatback pad.

        SHIKAKU-H : Hog ring

        NOTE:

        Remove all pieces of hog rings and discard them.



  1. Remove the front seat assembly. Refer to REMOVAL AND INSTALLATION .
  2. Remove the lift lever.
    1. Release pawls and remove the lift lever cap (1) (if equipped).
      Fig 1: Pawls And Remove The Lift Lever Cap (1)
      GNSAWJIA0932ZZ-932Courtesy of NISSAN NORTH AMERICA, INC.
    2. Remove screws and the lift lever (2) (if equipped).

      MARU-H : Pawl

  3. Remove the recline lever.
    1. Remove snap ring (1) using a suitable tool, then the recline lever (2).
      Fig 2: Identifying Seat Reclining Device Lever And Snap Ring
      G08203947Courtesy of NISSAN NORTH AMERICA, INC.
  4. Remove the seat cushion outer finisher (LH).
    1. Remove the screw (A).
      Fig 3: Screw (A), Metal Clips, Then Remove Seat Cushion Outer Finisher (LH) (1)
      GNSJMJIA6006ZZ-006Courtesy of NISSAN NORTH AMERICA, INC.
    2. Release the metal clips, then remove the seat cushion outer finisher (LH) (1).

      SHIKAKU-H : Metal clip

  5. Remove the seat belt buckle.
    1. Unclip the seat belt buckle harness clip and connector clip from seat frame assembly.
    2. Remove the seat belt buckle anchor bolt and the seat belt buckle.
  6. Remove the seat cushion outer finisher (RH).
    1. Remove the screw (B).
      Fig 4: Screw (B), Seat Cushion Trim (A) & Seat Cushion Outer Finisher (Rh) (1)
      GNSAWJIA0933ZZ-933Courtesy of NISSAN NORTH AMERICA, INC.
    2. Lift up seat cushion trim (A).
    3. Slide seat cushion outer finisher (RH) (1) rearward to release pawl and remove.

      MARU-H : Pawl

  7. Remove the seat cushion assembly from the seat frame assembly.
    1. Release the seatback trim J-clips (C) and seat cushion J-clips (B) from the seat cushion frame.
      Fig 5: Locating Seatback Trim J-Clips, Seat Cushion J-Clips And Bolt
      G09015339Courtesy of NISSAN NORTH AMERICA, INC.
    2. Unclip the harness from the seat cushion frame.
      NOTE:

      Take note of harness routing and attachment location for accurate installation.

    3. Remove bolts (A) and the seat cushion assembly.
  8. Remove seat cushion trim and seat cushion pad as an assembly from the seat cushion frame:
    1. Release string at locations (A) from seat cushion frame (1).
      Fig 6: String At Locations (A) From Seat Cushion Frame (1)
      GNSJMJIA6008ZZ-008Courtesy of NISSAN NORTH AMERICA, INC.

      ARROW : Front

    2. Loosen string and remove the seat cushion pad and seat cushion trim.
  9. Separate the seat cushion trim from the seat cushion pad.
    1. Remove the hog rings and separate the seat cushion trim (1) from the seat cushion pad.
      Fig 7: Locating Hog Rings And Separate The Seat Cushion Trim (1)
      GNSALJIA0990ZZ-990Courtesy of NISSAN NORTH AMERICA, INC.

      SHIKAKU-H : Hog ring

      NOTE:

      Remove all pieces of hog rings and discard them.