Diagnosis Procedure
- CHECK GROUND CONNECTIONS
- Turn ignition switch OFF.
- Loosen and retighten ground screws on the body.
Refer to "GROUND INSPECTION ".
Courtesy of NISSAN NORTH AMERICA, INC.
OK or NG
OK: GO TO 2.
NG: Repair or replace ground connections.
- RETIGHTEN A/F SENSOR 1 AND HEATED OXYGEN SENSOR 2
Loosen and retighten the A/F sensor 1 and heated oxygen sensor 2. Refer to , "REMOVAL AND INSTALLATION ".
GO TO 3.
- CHECK FOR EXHAUST GAS LEAK
- Start engine and run it at idle.
- Listen for an exhaust gas leak before the three way catalyst 2.
Is exhaust gas detected?
YES: Repair or replace.
NO: GO TO 4.
- CHECK FOR INTAKE AIR LEAK
- Start engine and run it at idle.
- Listen for an intake air leak after the mass air flow sensor.
OK or NG
OK: GO TO 5.
NG: Repair or replace.
- CLEAR THE SELF-LEARNING DATA.
With CONSULT
- Start engine and warm it up to normal operating temperature.
- Select "SELF-LEARNING CONT" in "WORK SUPPORT" mode with CONSULT.
- Clear the self-learning control coefficient by touching "CLEAR".
- Run engine for at least 10 minutes at idle speed.
- Check 1st trip DTC.
Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected? Is it difficult to start engine?
Is it difficult to start engine?
Without CONSULT
- Start engine and warm it up to normal operating temperature.
- Turn ignition switch OFF.
- Disconnect mass air flow sensor (1) harness connector.
- ←: Vehicle front
- Restart engine and let it idle for at least 5 seconds.
- Stop engine and reconnect mass air flow sensor harness connector.
- Check that DTC P0102 is displayed.
- Erase the DTC memory. Refer to "EMISSION-RELATED DIAGNOSTIC INFORMATION ".
- Check that DTC P0000 is displayed.
- Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0171, P0172, P0174 or P0175 detected?
Is it difficult to start engine?
Is it difficult to start engine?
Yes or No
Yes >> Perform trouble diagnosis for DTC P0171, P0174 or P0172, P0175. Refer to DTC P0171, P0174 FUEL INJECTION SYSTEM FUNCTION or DTC P0172, P0175 FUEL INJECTION SYSTEM FUNCTION .
No >> GO TO 6.
- CHECK HARNESS CONNECTOR
- Turn ignition switch OFF.
- Disconnect air fuel ratio (A/F) sensor 1 harness connector.
- Air fuel ratio (A/F) sensor 1 (Bank 1) harness connector (1)
- Air fuel ratio (A/F) sensor 1 (Bank 1) (2)
- Air fuel ratio (A/F) sensor 1 (Bank 2) (3)
- Air fuel ratio (A/F) sensor 1 (Bank 2) harness connector (4)
- Check harness connector for water.
Water should no exist .
Courtesy of NISSAN NORTH AMERICA, INC.
OK or NG
OK: GO TO 7.
NG: Repair or replace harness connector.
- CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT
- Turn ignition switch ON.
- Check voltage between A/F sensor 1 terminal 4 and ground with CONSULT or tester.
Voltage: Battery voltage
Courtesy of NISSAN NORTH AMERICA, INC.
OK or NG
OK: GO TO 9.
NG: GO TO 8.
- DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E3, F2 (Bank 1)
- Harness connectors E17, F10 (Bank 2)
- Fuse block (J/B) connector E43 (Bank 1)
- Fuse block (J/B) connector E39 (Bank 2)
- 10 A fuse (Bank 1)
- 15 A fuse (Bank 2)
- Harness for open or short between A/F sensor 1 and fuse
Repair or replace harness or connectors.
- CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
- Turn ignition switch OFF.
- Disconnect ECM harness connector.
- Check harness continuity between the following terminals. Refer to Wiring Diagram .
Bank A/F sensor 1 terminal ECM terminal 1 1 45 2 49 2 1 53 2 57 Continuity should exist .
- Check harness continuity between the following terminals and ground. Refer to Wiring Diagram .
Bank 1 Bank 2 A/F sensor terminal ECM terminal A/F sensor terminal ECM terminal 1 45 1 53 2 49 2 57 Continuity should not exist .
- Also check harness for short to power.
OK or NG
OK: GO TO 10.
NG: Repair open circuit or short to ground or short to power in harness or connectors.
- CHECK A/F SENSOR 1 HEATER
Refer to "COMPONENT INSPECTION ".
OK or NG
OK: GO TO 11.
NG: GO TO 13.
- CHECK HEATED OXYGEN SENSOR 2
Refer to "COMPONENT INSPECTION ".
Is the inspection result normal?
YES: GO TO 12.
NO: Replace heated oxygen sensor 2. Refer to , "REMOVAL AND INSTALLATION ".
- CHECK INTERMITTENT INCIDENT
Perform TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT .
OK or NG
OK: GO TO 13.
NG: Repair or replace.
- REPLACE AIR FUEL RATIO (A/F) SENSOR 1
Replace malfunctioning air fuel ratio (A/F) sensor 1. Refer to , "REMOVAL AND INSTALLATION ".
CAUTION:- Discard any air fuel ratio (A/F) sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; use a new one.
- Before installing new air fuel ratio (A/F) sensor, clean exhaust system threads using heated oxygen sensor thread cleaner [commercial service tool (J-43897-18 or J-43897-12)] and approved anti-seize lubricant (commercial service tool).
GO TO 14.
- CONFIRM A/F ADJUSTMENT DATA
- Turn ignition switch ON.
- Select "A/F ADJ-B1" and "A/F ADJ-B2" in "DATA MONITOR" mode with CONSULT.
- Check that "0.000" is displayed on CONSULT screen.
OK or NG
OK: INSPECTION END
NG: GO TO 15.
- CLEAR THE SELF-LEARNING DATA
With CONSULT
- Start engine and warm it up to normal operating temperature.
- Select "SELF-LEARNING CONT" in "WORK SUPPORT" mode with CONSULT.
- Clear the self-learning control coefficient by touching "CLEAR".
Without CONSULT
- Start engine and warm it up to normal operating temperature.
- Turn ignition switch OFF.
- Disconnect mass air flow sensor harness (1) connector.
- ←: Vehicle front
- Restart engine and let it idle for at least 5 seconds.
- Stop engine and reconnect mass air flow sensor harness connector.
- Check that DTC P0102 is displayed.
- Erase the DTC memory. Refer to "EMISSION-RELATED DIAGNOSTIC INFORMATION ".
- Check that DTC P0000 is displayed.
GO TO 16.
- CONFIRM A/F ADJUSTMENT DATA
- Turn ignition switch OFF and then ON.
- Select "A/F ADJ-B1" and "A/F ADJ-B2" in "DATA MONITOR" mode with CONSULT.
- Check that "0.000" is displayed on CONSULT screen.
INSPECTION END