LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2012 >> Frontier SL, RWD >> Repair and Diagnosis >> Transmission >> Automatic Transmission >> Unit Disassembly And Assembly >> Assembly >> Assembly (2)

Assembly (2)

  1. Install O-ring to oil pump assembly.
    CAUTION:
    • Do not reuse O-ring.
    • Apply ATF to O-ring.
    Fig 1: Installing O-ring
    G08135172Courtesy of NISSAN NORTH AMERICA, INC.
  2. Install bearing race to oil pump assembly.
    CAUTION: Apply petroleum jelly to bearing race.
    Fig 2: Identifying Bearing Race
    G08135173Courtesy of NISSAN NORTH AMERICA, INC.
  3. Install oil pump assembly in transmission case.
    CAUTION: Apply ATF to oil pump bearing.
    Fig 3: Installing Oil Pump Assembly
    G08135174Courtesy of NISSAN NORTH AMERICA, INC.
  4. Apply recommended sealant (Genuine RTV Silicone Sealant or equivalent. Refer to "RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS ".) to oil pump assembly as shown below.
    CAUTION: Completely remove all moisture, oil, old sealant and any foreign material from the oil pump bolts and oil pump bolt mating surfaces.
    Fig 4: Identifying Sealant
    G08135175Courtesy of NISSAN NORTH AMERICA, INC.
  5. Tighten oil pump bolts to specified torque.

    Oil pump bolts: 48 N.m (4.9 kg-m, 35 ft-lb) 

    Fig 5: Locating Oil Pump Bolts
    G08135176Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION: Apply ATF to oil pump bushing.
  6. Install O-ring to input clutch assembly.
    CAUTION:
    • Do not reuse O-ring.
    • Apply ATF to O-ring.
    Fig 6: Identifying O-Ring
    G08135177Courtesy of NISSAN NORTH AMERICA, INC.
  7. Install converter housing to transmission case and tighten bolts to specified torque.

    Converter housing bolt: 52 N.m (5.3 kg-m, 38 ft-lb) 

    Self-sealing bolt (A): 61 N.m (6.2 kg-m, 45 ft-lb) 

    Fig 7: Locating Converter Housing Bolts
    G08135178Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION: Do not reuse self-sealing bolt (A).
  8. Make sure that brake band (1) does not close input speed sensor hole (A).
    Fig 8: Identifying Brake Band & Input Speed Sensor Hole
    G08135179Courtesy of NISSAN NORTH AMERICA, INC.
  9. Connect TCM connector (1) and transmission range switch connector (2).
    Fig 9: Identifying TCM & Transmission Range Switch Connectors
    G08135180Courtesy of NISSAN NORTH AMERICA, INC.
  10. Install A/T assembly harness connector to control valve with TCM.
    Fig 10: Installing A/T Assembly Harness Connector
    G08135181Courtesy of NISSAN NORTH AMERICA, INC.
  11. Connect TCM connectors.
    Fig 11: Identifying TCM Connectors
    G08135182Courtesy of NISSAN NORTH AMERICA, INC.
  12. Install O-ring to A/T assembly harness connector.
    CAUTION:
    • Do not reuse O-ring.
    • Apply ATF to O-ring.
    Fig 12: Identifying O-Ring & A/T Assembly Harness Connector
    G08135183Courtesy of NISSAN NORTH AMERICA, INC.
  13. Install new O-ring (1) in plug (2).
    CAUTION:
    • Do not reuse O-ring.
    • Apply ATF to O-ring.
    • O-ring should be free of contamination.
    Fig 13: Identifying O-Ring & Plug
    G08135184Courtesy of NISSAN NORTH AMERICA, INC.
  14. Install plug (2) to bracket (1).
    Fig 14: Installing Bracket & Plug
    G08135185Courtesy of NISSAN NORTH AMERICA, INC.
  15. Install plug (1) [with bracket (2)] to control valve with TCM and tighten bolt (← ) to specified torque.

    Bracket bolt: 7.9 N.m (0.81 kg-m, 70 in-lb) 

    Fig 15: Locating Plug, Bracket & Bolts
    G08135186Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION: Adjust bolt hole of bracket to bolt hole of control valve.
  16. Install control valve with TCM in transmission case.
    Fig 16: Identifying Brake Band & Input Speed Sensor Hole
    G08135187Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • Make sure that input speed sensor is securely installed into input speed sensor hole (A).
    • Hang down output speed sensor harness toward outside so as not to disturb installation of control valve with TCM.
    • Adjust A/T assembly harness connector of control valve with TCM to terminal hole of transmission case.
    • Assemble it so that manual valve cutout is engaged with manual plate projection.
    Fig 17: Identifying Manual Valve & Plate
    G08135188Courtesy of NISSAN NORTH AMERICA, INC.
  17. Install bolts (A), (B) and (C) to control valve with TCM.
    Fig 18: Identifying Control Valve With TCM Bolts
    G08135189Courtesy of NISSAN NORTH AMERICA, INC.
    Bolt symbol Length mm (in) Number of bolts
    A 42 (1.65) 5
    B 55 (2.17) 6
    C 40 (1.57) 1
  18. Tighten bolt (A), (B) and (C) temporarily to prevent dislocation. After that tighten them in order (A → B → C), and then tighten other bolts.
    Fig 19: Identifying TCM Bolt Location
    G08135190Courtesy of NISSAN NORTH AMERICA, INC.
    Bolt symbol A B C
    Number of bolts 5 6 1
    Length mm (in) 42 (1.65) 55 (2.17) 40 (1.57)
    Tightening torque N.m (km-g, in-lb) 7.9 (0.81, 70) With ATF applied
    7.9 (0.81, 70)
  19. Connect output speed sensor connector (1).
    Fig 20: Identifying Output Speed Sensor Connector
    G08135191Courtesy of NISSAN NORTH AMERICA, INC.
  20. Securely fasten output speed sensor harness with terminal clip (← ).
    Fig 21: Locating Output Speed Sensor Harness Terminal Clip
    G08135192Courtesy of NISSAN NORTH AMERICA, INC.
  21. Pull down A/T assembly harness connector.
    CAUTION: Do not damage connector.
    Fig 22: Identifying A/T Assembly Harness Connector
    G08135193Courtesy of NISSAN NORTH AMERICA, INC.
  22. Install snap ring to A/T assembly harness connector.
    Fig 23: Installing Snap Ring
    G08135194Courtesy of NISSAN NORTH AMERICA, INC.
  23. Install magnets in oil pan.
    Fig 24: Identifying Magnets
    G08135195Courtesy of NISSAN NORTH AMERICA, INC.
  24. Install oil pan to transmission case. Refer to "Removal and Installation ".
  25. Install torque converter.
    1. Pour ATF into torque converter.
      NOTE:
      • Approximately 2 liters (2-1/8 US qt. 1-3/4 Imp qt) of fluid is required for a new torque converter.
      • When reusing old torque converter, add the same amount of fluid as was drained.
      Fig 25: Pouring ATF Into Torque Converter
      G08135196Courtesy of NISSAN NORTH AMERICA, INC.
    2. Install torque converter while aligning notches of torque converter with notches of oil pump.
      CAUTION: Install torque converter while rotating it.
      Fig 26: Installing Torque Converter
      G08135197Courtesy of NISSAN NORTH AMERICA, INC.
    3. Measure distance "A" to make sure that torque converter is in proper position.

    Distance "A": 25.0 mm (0.98 in) or more 

    Fig 27: Identifying Distance A
    G08135198Courtesy of NISSAN NORTH AMERICA, INC.