LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2012 >> Frontier SL, RWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 10 (Front Axle) >> Unit Disassembly And Assembly >> Drive Shaft >> Disassembly and Assembly >> Assembly

Disassembly and Assembly: Assembly

WARNING: This page is about a different variant/trim than selected.

Final Drive Side

  1. Wrap the serrated part of the shaft with tape. Install the boot band and boot to shaft.
    NOTE: Discard the old boot band and boot and use a new one for assembly.
  2. Remove the tape wound around the serrated part of the shaft.
    Fig 1: Identifying Tape
    G04876506Courtesy of NISSAN NORTH AMERICA, INC.
  3. Install the ball cage, steel ball, and inner race assembly on the shaft, and secure them using the snap ring.
    NOTE: Discard the old snap ring and use a new one for assembly.
    Fig 2: Identifying Ball Cage, Snap Ring & Shaft
    G04876507Courtesy of NISSAN NORTH AMERICA, INC.
  4. Insert the specified quantity of Genuine NISSAN Grease or equivalent, into the housing. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS " (United States and Canada), "FOR MEXICO: FLUIDS AND LUBRICANTS " (Mexico).

    Grease capacity: Refer to  "Drive Shaft ".

    CAUTION: If grease adheres to the boot mounting surface (indicated by * marks) on shaft and housing, boot may come off. Remove all grease from surfaces.
    Fig 3: Identifying Grease Application Area
    G04899092Courtesy of NISSAN NORTH AMERICA, INC.
  5. Install the stopper ring onto the housing.
    CAUTION:
    • Do not reuse stopper rings.
    • Make sure that housing and stopper ring are fully engaged.
  6. Install the boot securely into the grooves (indicated by * marks) as shown below.
    CAUTION: If there is grease on boot mounting surfaces (indicated by * marks) of shaft and housing, boot may come off. Remove all grease from surfaces.
  7. Check that the boot installation length (L) is the length indicated below. Insert a suitable tool into the large end of the boot. Bleed air from boot to prevent boot deformation.
    Fig 4: Installing Boot
    G07120000Courtesy of NISSAN NORTH AMERICA, INC.

    Boot installation length (L): Refer to  "Drive Shaft ".

    CAUTION:
    • The boot may break if the boot installation length is less than the specified value.
    • Do not to touch the tip of the suitable tool to the inside of the boot.
  8. Secure the big and small ends of the boot with the new boot bands as shown below.
    NOTE: Discard not reuse boot bands.
    Fig 5: Securing Boot Band
    G05378027Courtesy of NISSAN NORTH AMERICA, INC.
  9. Secure housing and shaft and then make sure that they are in the correct position when rotating boot. Use a new boot band if the boot band needs to be loosened to reposition the boot.
  10. Install circlip and dust cover to housing.
NOTE: Do not reuse circlip and dust cover.

Wheel Side

  1. Insert the Genuine NISSAN Grease or equivalent, into the joint sub-assembly serration hole until the grease begins to ooze from the ball groove and serration hole. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS " (United States and Canada), "FOR MEXICO: FLUIDS AND LUBRICANTS " (Mexico). After inserting the grease, use a shop cloth to wipe off the grease that has oozed out.
    Fig 6: Inserting Grease Into Joint Sub-Assembly
    G04876511Courtesy of NISSAN NORTH AMERICA, INC.
  2. Wrap the serrated part of the shaft with tape. Install the boot band and boot onto the shaft. Do not damage the boot.
    NOTE: Discard the old boot band and boot and use a new one for assembly.
  3. Remove the protective tape wound around the serrated part of the shaft.
    Fig 7: Identifying Tape
    G04876506Courtesy of NISSAN NORTH AMERICA, INC.
  4. Attach the circlip to the shaft. The circlip must fit securely into the shaft groove. Attach the nut to the joint sub-assembly.

    Use a soft hammer to press-fit the circlip.

    NOTE: Discard the old circlip and use a new one for assembly.
    Fig 8: Attaching Circlip To Drive Shaft
    G07019352Courtesy of NISSAN NORTH AMERICA, INC.
  5. Insert the specified quantity of Genuine NISSAN Grease or equivalent, into the joint sub-assembly and the large end of the boot. Refer to "FOR USA AND CANADA: FLUIDS AND LUBRICANTS " (United States and Canada), "FOR MEXICO: FLUIDS AND LUBRICANTS " (Mexico).

    Grease capacity: Refer to  "Drive Shaft ".

    CAUTION: If grease adheres to the boot mounting surface (indicated by * marks) on shaft and housing, boot may come off. Remove all grease from surfaces.
    Fig 9: Identifying Grease Application Area
    G04899092Courtesy of NISSAN NORTH AMERICA, INC.
  6. Install the boot securely into the grooves (indicated by the * marks) as shown below.
    CAUTION: If there is grease on the boot mounting surfaces (indicated by the * marks) of the shaft and joint sub-assembly, the boot may come off. Remove all grease from the drive shaft surfaces.
  7. Check that the boot installation length (L) is the specified length. Insert a suitable tool into the big side of the boot. Bleed the air from the boot to prevent boot deformation.

    Boot installation length (L): Refer to  "Drive Shaft ".

    Fig 10: Installing Boot
    G05892947Courtesy of NISSAN NORTH AMERICA, INC.
    CAUTION:
    • The boot may break if the boot installation length is less than the specified length.
    • Do not contact inside surface of boot with the tip of the suitable tool.
  8. Secure large and small ends of the boot using new boot bands using tool as shown below.

    Tool number: KV40107300 (-) 

    Fig 11: Securing Boot Clamp
    G04902012Courtesy of NISSAN NORTH AMERICA, INC.
    NOTE: Do not reuse boot bands.
    • Secure boot band so that dimension (M) meets specification as shown below.
    • Fig 12: Identifying Dimension M
      G07015951Courtesy of NISSAN NORTH AMERICA, INC.

    Dimension (M): Refer to  "Boot Bands ".

  9. After installing the housing to the shaft, rotate the boot to check that it is positioned correctly. If the boot is not positioned correctly, remove the old boot bands then reposition the boot and secure the boot with new boot bands.