LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2011 >> Quest LE >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System - DTCS P1550 To P2A03 >> DTC P1805: Brake Switch >> Diagnosis Procedure

Diagnosis Procedure

  1. CHECK STOP LAMP SWITCH CIRCUIT
    1. Turn ignition switch OFF.
    2. Check the stop lamp when depressing and releasing the brake pedal.
      BRAKE PEDAL REFERENCE CHART

      Brake pedal Stop lamp
      Fully released Not illuminated
      Slightly depressed Illuminated

      Is the inspection result normal? 

      YES: GO TO  11.

      NO: GO TO 2.

  2. CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT
    1. Disconnect stop lamp switch harness connector.
    2. Check the voltage between stop lamp switch harness connector and ground.
      TERMINAL VOLTAGE REFERENCE CHART

      Stop lamp switch Ground Voltage
      Connector Terminal
      E115 1 Ground Battery voltage

      Is the inspection result normal? 

      YES: GO TO  4.

      NO: GO TO 3.

  3. DETECT MALFUNCTIONING PART

    Check the following.

    • Fuse block (J/B) connector E103
    • 10 A fuse (No. 7)
    • Harness for open or short between battery and stop lamp switch

      Repair open circuit, short to ground or short to power in harness or connectors.

  4. CHECK STOP LAMP RELAY GROUND CIRCUIT
    1. Turn ignition switch OFF.
    2. Disconnect stop lamp relay harness connector.
    3. Check the continuity between stop lamp relay harness connector and ground.
      TERMINAL CONTINUITY REFERENCE CHART

      Stop lamp relay Ground Continuity
      Connector Terminal
      E15 1 Ground Existed

      Is the inspection result normal? 

      YES: GO TO 5.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK STOP LAMP SWITCH INPUT SIGNAL CIRCUIT
    1. Connect stop lamp switch harness connector.
    2. Turn ignition switch ON.
    3. Check the voltage between stop lamp relay harness connector and ground.
      TERMINAL VOLTAGE REFERENCE CHART

      Stop lamp relay Ground Condition Voltage (V)
      Connector Terminal
      E15 2 Ground Brake pedal Slightly depressed Battery voltage
      Fully released Approx. 0

      Is the inspection result normal? 

      YES: GO TO  7.

      NO: GO TO 6.

  6. DETECT MALFUNCTIONING PART

    Check the following.

    • Harness for open or short between stop lamp switch and stop lamp relay

      Is the inspection result normal? 

      YES: GO TO  9.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK STOP LAMP RELAY POWER SUPPLY CIRCUIT

    Check the voltage between stop lamp relay harness connector and ground.

    TERMINAL VOLTAGE REFERENCE CHART

    Stop lamp relay Ground Voltage (V)
    Connector Terminal
    E15 5 Ground Battery voltage

    Is the inspection result normal? 

    YES: GO TO 8.

    NO: Repair open circuit or short to ground or short to power in harness or connectors.

  8. CHECK STOP LAMP RELAY INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
    1. Turn ignition switch OFF.
    2. Disconnect stop lamp relay harness connector.
    3. Check the continuity between stop lamp relay harness connector and ECM harness connector.
      TERMINAL CONTINUITY REFERENCE CHART

      ECM Stop lamp relay Continuity
      Connector Terminal Connector Terminal
      E16 122 E15 3 Existed
    4. Also check harness for short to ground and short to power.

      Is the inspection result normal? 

      YES: GO TO  10.

      NO: Repair open circuit or short to ground or short to power in harness or connectors.

  9. CHECK STOP LAMP SWITCH

    Refer to "COMPONENT INSPECTION (STOP LAMP SWITCH) ".

    Is the inspection result normal? 

    YES: GO TO  11.

    NO: Replace stop lamp switch.

  10. CHECK STOP LAMP RELAY

    Refer to "COMPONENT INSPECTION (STOP LAMP RELAY) ".

    Is the inspection result normal? 

    YES: GO TO 11.

    NO: Replace stop lamp relay.

  11. CHECK INTERMITTENT INCIDENT

    Refer to "INTERMITTENT INCIDENT ".

    INSPECTION END