LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2006 >> Sentra SE-R Spec V >> Repair and Diagnosis >> Transmission >> Manual Transmission >> RS6F51H >> MAINSHAFT And Gears >> Disassembly and Assembly >> Assembly

Disassembly and Assembly: Assembly

  1. Install the reverse main gear using Tool as shown.
    Fig 1: Installing Reverse Main Gear Using Tool
    G04192743Courtesy of NISSAN MOTOR CO., U.S.A.
    CAUTION: Install with the orientation of reverse main gear as shown.
    Fig 2: Identifying Reverse Main Gear
    G04192744Courtesy of NISSAN MOTOR CO., U.S.A.
  2. Install the 1st bushing using Tool as shown.
  3. Install the needle bearing, and then the 1st main gear.
    Fig 3: Installing 1st Bushing Using Tool
    G04192745Courtesy of NISSAN MOTOR CO., U.S.A.
  4. Install the spread spring, shifting insert, and a new 1st-2nd synchronizer hub onto the 1st-2nd coupling sleeve.
    CAUTION:
    • Do not reuse 1st-2nd synchronizer hub
    • Install with the orientation of the new synchronizer hub as shown.
      Fig 4: Identifying Synchronizer Hub Orientation
      G04192746Courtesy of NISSAN MOTOR CO., U.S.A.
    • Install with the orientation of coupling sleeve as shown.
      Fig 5: Identifying Coupling Sleeve
      G04192747Courtesy of NISSAN MOTOR CO., U.S.A.
    • Do not hook the ends of the two spread springs (front and back have two each) on the same shifting insert.
    Fig 6: Identifying Spread Springs Center Projection
    G04192748Courtesy of NISSAN MOTOR CO., U.S.A.
  5. Install the 1st-2nd coupling sleeve assembly onto the mainshaft, and the synchronizer hub assembly onto the mainshaft using Tool as shown.
    CAUTION:
    • Outer baulk ring, synchronizer cone, and inner baulk ring on the 2nd gear-side must have been removed.
    • Install the coupling sleeve with the proper orientation.
    Fig 7: Installing 1st-2nd Coupling Sleeve Assembly And Synchronizer Hub Assembly Onto Mainshaft
    G04192749Courtesy of NISSAN MOTOR CO., U.S.A.
  6. Install the 2nd bushing using Tool as shown.
  7. Install the outer baulk ring, synchronizer cone, and inner baulk ring on 2nd gear-side.
  8. Install the 2nd needle bearing and 2nd gear.
    Fig 8: Installing 2nd Bushing Using Tool
    G04192750Courtesy of NISSAN MOTOR CO., U.S.A.
  9. Install the 3rd main gear.
    CAUTION: Install the 3rd main gear with the orientation as shown.
  10. Install the 3rd-4th mainshaft spacer.
    Fig 9: Installing 3rd Main Gear
    G04192751Courtesy of NISSAN MOTOR CO., U.S.A.
  11. Measure the dimension "C1 ". Select a suitable adjusting shim so that the dimension "C1 " satisfies the specified standard value, and install it onto the mainshaft.

    Standard for dimension "C 1  ": 173.85 - 173.95 mm (6.844 - 6.848 in) 

    CAUTION: Only 1 adjusting shim can be selected.
    Fig 10: Measuring Dimension
    G04192752Courtesy of NISSAN MOTOR CO., U.S.A.

    Adjusting Shim 

    ADJUSTING SHIMS THICKNESS SPECIFICATIONS

    Thickness Part number Thickness Part number
    0.52 mm (0.0205 in) 32238 8H500 0.84 mm (0.0331 in) 32238 8H504
    0.60 mm (0.0236 in) 32238 8H501 0.92 mm (0.0362 in) 32238 8H505
    0.68 mm (0.0268 in) 32238 8H502 1.00 mm (0.0394 in) 32238 8H506
    0.76 mm (0.0299 in) 32238 8H503 1.08 mm (0.0425 in) 32238 8H507
  12. Install the 4th main gear with the specified orientation as shown, using Tool as shown.
    CAUTION: Install the 4th main gear with the orientation as shown.
    Fig 11: Installing 4th Main Gear
    G04192753Courtesy of NISSAN MOTOR CO., U.S.A.
  13. Install the 5th main gear with the specified orientation as shown, using Tool as shown.
    CAUTION: Install the 5th main gear with the orientation as shown.
  14. Fig 12: Installing 5th Main Gear
    G04192754Courtesy of NISSAN MOTOR CO., U.S.A.
  15. Install the 5th-6th mainshaft spacer.
  16. Install the 6th main gear using Tool as shown.
    Fig 13: Installing 6th Main Gear
    G04192755Courtesy of NISSAN MOTOR CO., U.S.A.
  17. Select the 6th main adjusting shim and then install it onto the mainshaft.
    • Calculate thickness "S" of 6th main adjusting shim by procedure below so that end play dimension between 6th main gear and mainshaft rear bearing becomes the dimension specified.

      End play: 0 - 0.1 mm (0 - 0.004 in) 

      Dimension "S" = ("S 1  " - "S 2  ") + End play 

      "S": Thickness of adjusting shim 

      "S 2  ": Dimension from mainshaft standard face to mainshaft rear bearing press-fit end face 

      "S 2  ": Dimension from mainshaft standard face to 6th main gear end face 

      CAUTION: Only 1 adjusting shim can be selected.
    Fig 14: Identifying Dimensions From Mainshaft To Components
    G04192756Courtesy of NISSAN MOTOR CO., U.S.A.

    Adjusting Shim 

    ADJUSTING SHIMS THICKNESS SPECIFICATIONS

    Thickness Part number Thickness Part number
    0.88 mm (0.0346 in) 32237 8H560 1.20 mm (0.0472 in) 32237 8H564
    0.96 mm (0.0378 in) 32237 8H561 1.28 mm (0.0504 in) 32237 8H565
    1.04 mm (0.0409 in) 32237 8H562 1.36 mm (0.0535 in) 32237 8H566
    1.12 mm (0.0441 in) 32237 8H563
    1. Using a height gauge, measure the dimension "S1 " and "S2 " as shown.
    2. Install the selected 6th main adjusting shim to the mainshaft.
  18. Install the mainshaft rear bearing using Tool as shown.
    Fig 15: Installing Mainshaft Rear Bearing Using Tool
    G04192757Courtesy of NISSAN MOTOR CO., U.S.A.
  19. Install the C-ring onto the mainshaft, and check that the end play of mainshaft rear bearing meets specifications.

    End play standard value: 0 - 0.06 mm (0 - 0.0024 in) 

    • If the measurement is outside the specified standard value, reselect a new C-ring.
    Fig 16: Checking End Play Of Mainshaft Rear Bearing
    G04192758Courtesy of NISSAN MOTOR CO., U.S.A.

    C-Ring 

    C-RING THICKNESS SPECIFICATIONS

    Thickness Part number Thickness Part number
    2.535 mm (0.0866 in) 32348 8H800 2.835 mm (0.1116 in) 32348 8H810
    2.565 mm (0.1010 in) 32348 8H801 2.865 mm (0.1128 in) 32348 8H811
    2.595 mm (0.1022 in) 32348 8H802 2.895 mm (0.1140 in) 32348 8H812
    2.625 mm (0.1033 in) 32348 8H803 2.925 mm (0.1152 in) 32348 8H813
    2.655 mm (0.1045 in) 32348 8H804 2.955 mm (0.1163 in) 32348 8H814
    2.685 mm (0.1057 in) 32348 8H805 2.985 mm (0.1175 in) 32348 8H815
    2.715 mm (0.1069 in) 32348 8H806 3.015 mm (0.1187 in) 32348 8H816
    2.745 mm (0.1081 in) 32348 8H807 3.045 mm (0.1199 in) 32348 8H817
    2.775 mm (0.1093 in) 32348 8H808 3.075 mm (0.1211 in) 32348 8H818
    2.805 mm (0.1104 in) 32348 8H809
  20. Fit the C-ring holder, and install the snap ring as shown.
    Fig 17: Installing C-Ring Holder And Snap Ring
    G04192759Courtesy of NISSAN MOTOR CO., U.S.A.
  21. Check the end play of 1st and 2nd main gears as shown.

    End play standard value 

    1st gear: 0.20 - 0.30 mm (0.0079 - 0.0118 in) 

    2nd gear: 0.06 - 0.16 mm (0.0024 - 0.0063 in) 

    Fig 18: Checking End Play Of 1st And 2nd Main Gears
    G04192760Courtesy of NISSAN MOTOR CO., U.S.A.