LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2005 >> Altima SE-R, Automatic >> Repair and Diagnosis >> Quick Lookups >> Technical Bulletins >> Campaigns >> Other Variant >> Engine Control Systems >> Voluntary Recall Campaign 2002, 2005, 2006 ALTIMA/SENTRA ECM Reprogram (2.5L) (NTB07-081)

Voluntary Recall Campaign 2002, 2005, 2006 ALTIMA/SENTRA ECM Reprogram (2.5L) (NTB07-081)

WARNING: This page is about the Altima Base, which is a different variant/trim than selected.
Publication date: 2007-12-08
Reference number: NTB07-081

VOLUNTARY RECALL CAMPAIGN 2002, 2005, 2006 ALTIMA/SENTRA ECM REPROGRAM (2.5L)

VOLUNTARY RECALL CAMPAIGN 2002, 2005, 2006 ALTIMA/SENTRA ECM REPROGRAM (2.5L)

SERVICE CAMPAIGN BULLETIN

Reference Number(s): NTB07-081, Date of Issue:  December 8, 2007
NISSAN: 2011 M56 (Y51) - VK56 engine only
CAMPAIGN ID #/NHTSA #: P0353/07V-527
APPLIED VEHICLES: 2011 M56 (Y51) - VK56 engine only
APPLIED VINS: 2002 Altima: 1N4AL11**2C 100000 - 719020; 2005 Altima: 1N4AL11**5C 100003 - 957025; 1N4AL11**5N 400000 - 934180; 2006 Altima: 1N4AL11**6C 100004 - 271080; 1N4AL11**6N 300001 - 462144; 2002 Sentra: 3N1AB51**2L 700019 - 730184; 2005 Sentra: 3N1AB51**5L 450088 - 597016; 2006 Sentra: 3N1AB51**6L 450295 - 632423

INTRODUCTION

Nissan has determined that a defect which relates to motor vehicle safety exists in some 2002 and 2005-2006 model year Nissan Altima and Sentra vehicles equipped with the 2.5 liter engine. On some of these vehicles there is a possibility that the engine might stop running while being driven due to the program in the Electronic Control Module (engine computer). If the engine stops running while driving, this could result in a crash without warning. To prevent this potential condition, Nissan is conducting a Voluntary Safety Recall Campaign to reprogram the Electronic Control Module.

IDENTIFICATION NUMBER

Nissan has assigned identification number R0712 to this campaign. This number must appear on all communications and documentation of any nature dealing with this campaign.

NUMBER OF VEHICLES POTENTIALLY AFFECTED

The number of vehicles potentially affected is approximately 653,900

DEALER RESPONSIBILITY

It is the dealers responsibility to check Service Comm for the campaign status on each vehicle falling within the range of this voluntary safety recall which for any reason enters the service department. This includes vehicles purchased from private parties or presented by transient (tourist) owners and vehicles in a dealer's inventory. Federal law requires that new vehicles in dealer inventory which are the subject of a safety recall must be corrected prior to sale. Failure to do so can result in civil penalties by the National Highway Traffic Safety Administration.  While federal law applies only to new vehicles, Nissan strongly encourages dealers to correct any used vehicles in their inventory before they are retailed.

REPAIR OVERVIEW

G07773467

SERVICE PROCEDURE

Before beginning this Service Procedure, use CONSULT-II to make sure there are no DTCs stored  in the ECM.

Repairs for stored DTCs must be done before performing the ECM reprogramming. Use ASIST for DTC diagnostic and repair information.

Repairs for stored DTCs are not related to this campaign. 

Check the Current ECM Part Number (P/N)

  1. With the Diagnostic Card (red/white card) in CONSULT-II and CONSULT-II turned "ON", print the ECM Part Number as follows:

    START  (Nissan) >> ENGINE >> ECM PART NUMBER >> COPY 

  2. Attach this printout to the Repair Order.
    • Figure A is an example of the ECM Part Number printout.
    G07773468
  3. Using the ECM P/N printout:
    • Compare your vehicle's ECM P/N to those shown under Current ECM P/N  in Chart A, on the next page.

Chart A

From → To 

CHART A

MODEL YEAR Vehicle Configuration Current ECM P/Ns Before Reprogramming New ECM P/N's
Altima (L31) with 2.5L engine 2002 A/T with ASCD 23710-8J000, -8J001, -9J003, -9J004, -9J00A 23710-9J00B
A/T 23710-8J010, -8J011, -9J008, -9J009, -9J03A 23710-9J03B
M/T with ASCD 23710-8J060, -8J061, -9J013, -9J014,-9J01A 23710-9J01B
MT 23710-8J070, -8J071, -9J018, -9J019,-9J04A 23710-9J04B
2005 50 state A/T with ASCD (ULEV) 23710-9J505, -9J506, -9J507, -9J51A, -9J51B 23710-9J51C
CAL A/T with ASCD (SULEV) 23710-9J560,-9J561, -9J562, -9J55A, -9J55C, -9J55D 23710-9J57E
23710-9J55B, -9J55E 23710-9J59D
50 state A/T (ULEV) 23710-9J500, -9J501, -9J502, -9J50A, -9J50B 23710-9J50C
A/T CAL (SULEV) 23710-9J520, -9J521, -9J522, -9J54A, -9J54C, 9J54D 23710-9J56E
23710-9J54B, -9J54E 23710-9J58D
50 state M/T with ASCD (ULEV) 23710-9J515, -9J516, -9J517, -9J53A 23710-9J53B
CAL M/T with ASCD (SULEV) 23710-9J570, -9J571, -9J572, -9J57B, -9J57C 23710-9J59C
23710-9J57A, -9J57D 23710-9J59E
50 state MT (ULEV) 23710-9J510,-9J511,-9J512,-9J52A 23710-9J52B
CAL M/T (SULEV) 23710-9J565, -9J566, -9J567, -9J56B, -9J56C 23710-9J58C
23710-9J56A, -9J56D 23710-9J58E
2006 50 state A/T with ASCD (ULEV) 23710-ZD81A, -ZD81B, -ZD81C, -ZD81D,-ZD81E 23710-ZD89A
CAL A/T with ASCD (SULEV) 23710-ZD85A, -ZD85B, -ZD85C, -ZD85D 23710-ZD85E
50 state A/T (ULEV) 23710-ZD80A, -ZD80B, -ZD80C, -ZD80D, -ZD80E 23710-ZD88A
A/T CAL (SULEV) 23710-ZD84A, -ZD84B, -ZD84C, -ZD84D 23710-ZD84E
50 state M/T with ASCD (ULEV) 23710-ZD83A, -ZD83B, -ZD83C, -ZD83D 23710-ZD83E
CAL M/T with ASCD (SULEV) 23710-ZD87A, -ZD87B, -ZD87C, -ZD87D 23710-ZD87E
50 state MT (ULEV) 23710-ZD82A, -ZD82B, -ZD82C, -ZD82D 23710-ZD82E
CAL M/T (SULEV) 23710-ZD86A, -ZD86B, -ZD86C, -ZD86D 23710-ZD86E
Sentra (B15) with 2.5L engine 2002 A/T 23710-8U000, -8U001, -8U502, -8U503, -8U50A 23710-8U50B
5 M/T 23710-8U010, -8U011, -8U512, -8U513, -8U51A 23710-8U51B
6 M/T 23710-8U020, -8U021, -8U022, -8U023, -8U02A 23710-8U02B
A/T with NATS 23710-8U040, -8U041, -8U542, -8U543, -8U54A 23710-8U54B
5 M/T with NATS 23710-8U060, -8U061, -8U562, -8U563, -8U56A 23710-8U56B
6 M/T with NATS 23710-8U070, -8U071, -8U072, -8U073, -8U07A 23710-8U07B
2005 FED A/T 23710-6Z500 23710-6Z57A
CAL A/T 23710-6Z510, -6Z53A 23710-6Z53B
FED A/T with NATS 23710-6Z505 23710-6Z58A
CAL A/T with NATS 23710-6Z515, -6Z54A 23710-6Z54B
M/T with NATS 23710-6Z560, -6Z56A 23710-6Z56B
M/T 23710-6Z520, -6Z55A 23710-6Z55B
2006 A/T 23710-ZG50B, -ZG50C, -ZG50D, -ZG58A 23710-ZG58B
A/T with NATS 23710-ZG51B, -ZG51C, -ZG51D, -ZG58E 23710-ZG58D
M/T 23710ZG52B, -ZG52C, -ZG52D, -ZG59A 23710-ZG59B
M/T with NATS 23710-ZG53B, -ZG53C, -ZG53D, -ZG59E 23710-ZG59D
  1. If your vehicle's ECM P/N matches  one of the Current ECM P/N's in the chart above:
    • Go to Reprogramming the ECM  .
  2. If your vehicle's ECM P/N does not match  one of the Current ECM P/N's in the chart above:
  • This campaign may not apply or has already been done.
  • Recheck Service Comm (campaign ID R0712) to confirm the vehicle you're working on is affected by this campaign. 

REPROGRAMMING THE ECM

Reprogramming should be performed by an OBDII Certified technician. 

The reprogramming procedure involves three general steps:

SETTING UP: 

  1. Install the Reprogramming Card into CONSULT-II.
    • Make sure CONSULT-II is disconnected from the vehicle and turned OFF.
    • The Reprogramming Software Card is the "orange" Card.
    • Use slot A-top slot (see Figure 1  ).
    G07773469

    Figure 1 

  2. Connect the AC power supply to CONSULT-II.
  3. Connect CONSULT-II to the ASIST PC with the special Ethernet cable (P/N 02002554 is printed on the cable).
    1. Connect one end to CONSULT-II at the "PC port".
    2. Connect the other end to the ASIST PC at the "Ethernet card" connection port.
  4. Confirm the CONSULT-II date and time are correctly set as follows:

    (This is necessary to provide a valid print-out for warranty claims.)

    1. With the Reprogramming card in slot A, turn "ON" CONSULT-II.
    2. Touch SUB MODE. 
    3. Touch SET DATE  (see Figure 2  ).
      1. If the date is not correct, touch the MONTH  , DAY  or YEAR  as needed. Then adjust it by using arrow keys. Once done, press SAVE  , press BACK  , and go to step D.
      2. If the date is OK, press BACK  and go to step D.
      G07773470

      Figure 2 

    4. Touch SET TIME  (see Figure 2  ).
    1. If time is not correct, touch the HOUR  , MINUTE  or AM/PM  as needed. Then adjust it by using arrow keys. Once done, press SAVE  , press BACK  and go to step 5.
    2. If time is OK, press BACK  and go to step 5.
    IMPORTANT:
    • If your ASIST PC is already being used to perform ECM Reprogramming, proceed to step 5 on the next page.
    • If you are unsure whether your ASIST PC has already been set up for ECM Reprogramming, look in ASIST, under "CONSULT Utilities" - "CONSULT-II Info" - "NISSAN" - "ECU Reprogramming". This will give you instructions for setting the Ethernet (IP) Address of the ASIST PC and CONSULT-II. You will need to do this before performing ECM reprogramming. 

    DOWNLOAD (TRANSFER) DATA FROM ASIST INTO CONSULT-II 

  5. From the ASIST PC main menu screen, select "CONSULT UTILITIES"  (see Figure 3  ).
    G07773471

    Figure 3 

  6. From the "CONSULT UTILITIES"  screen, select "ECM/TCM DATA"  (see Figure 4  ).
    G07773472

    Figure 4 

  7. Select the "ECU REPROGRAMMING DATA"  (see Figure 5  ) as follows:
    G07773473

    Figure 5 

    1. Select vehicle model and model year.
    2. Select the correct reprogramming data:
      1. Locate the specific "Model Configuration" (Example: QR25 A/T ASCD).
        NOTE:
        • Model Configuration may include items like engine type, transmission type, and vehicle options such as ASCD, TCS, ABS, etc.
        • Vehicle configuration can be verified using the "Current ECM P/N" in CHART A .
      2. Select (click on) the "To" number.
        NOTE: The "To" number reads: 23710-XXXXX.
      3. Write the "To" number on the Repair Order. You will need it later in the reprogramming process.
    3. Click on the "Add" button to add data to the "File(s) selected" list. This list is on the right side of the screen.
    4. Click the "CONTINUE"  button to proceed with CONSULT-II setup.
  8. Turn "ON" CONSULT-II as shown in Figure 6 
    G07773474

    Figure 6 

  9. Select Transfer files via LAN  (see Figure 7  ).
    NOTE: If you accidentally choose a menu option other than "Transfer Files via LAN"; turn CONSULT-II "OFF", and then back "ON" as shown in Figure 6  above.
    G07773475

    Figure 7 

    Set the CONSULT-II unit down for now and go to your ASIST PC. 

  10. Transfer (download) data from ASIST into CONSULT-II.
    1. On the ASIST screen, click on "Transfer"  (see Figure 8  ).
      G07773476

      Figure 8 

      • Data transfer will take about 15 seconds.
      • Transfer progress is displayed on the ASIST screen (see Figure 8  ).
    2. Wait until the data transfer is complete (see CAUTION below).
    CAUTION: DO NOT DISCONNECT THE ETHERNET CABLE UNTIL "COMPLETE" IS DISPLAYED AS SHOWN IN Figure 9  ON THE NEXT PAGE.
    • If the cable is disconnected before "Complete" is displayed, you MUST  restart the transfer (download) procedure; otherwise ECM damage can occur.
    • If the cable is disconnected during the transfer; wait for ASIST to display an "error" message, then click on "OK". Select "Backup", then return to step 6 on page 9.
    G07773477

    Figure 9 

  11. When transfer is complete (see Figure 9  ):
    1. Select (click on) "Okay"  , then "MAIN MENU"  .
    2. Turn "OFF" CONSULT-II.
    3. Disconnect the AC power cord and the Ethernet cable from CONSULT-II.

    DOWNLOAD NEW DATA FROM CONSULT-II INTO THE VEHICLE (REPROGRAM ECM) 

    CAUTION:
    • Perform this operation in four (4) sections. DO NOT SKIP any of these sections.
    • They must be performed in order, 1 through 4.

    Section 1: Connect a battery charger and CONSULT-II to the vehicle.

    Section 2: Confirm the vehicle battery voltage and CONSULT-II "Charger Input".

    Section 3: Perform ECM Reprogramming.

    Section 4: Perform ECM Reprogram Confirmation.

    Section 1: Connect a battery charger and CONSULT-II to the vehicle. 

  12. Confirm the ignition switch is "OFF".
  13. Connect a battery charger to the vehicle battery.
    1. Set the charger at a low charge rate (trickle charge).
      IMPORTANT: Do not perform ECU Reprogramming without  connecting a battery charger to the vehicle's battery. Permanent ECU damage can occur.
      Connecting a vehicle battery charger will maintain:
      • Proper CONSULT-II power supply during reprogramming-very important if the CONSULT-II battery is low.
      • Vehicle battery voltage level-especially on late model vehicles where the cooling fans come on during reprogramming.
  14. Connect CONSULT-II to the vehicle using the DLC-II cable with black Converter Box (see Figure 10  ).

    VERY IMPORTANT: 

    • Make sure the DLC-II is straight and fully plugged in to the vehicle.
    • Make sure all other DLC-II cable connections shown in Figure 10  are connected properly.
    G07773478

    Figure 10 

    CAUTION:
    • Nissan requires the use of essential tools shown in Figure 10  when performing ECM reprogramming.
    • J44200-10 "Pigtail" should not be removed from the CONSULT-II DDL Port. This "Pigtail" allows use of the stronger "quick disconnect" cable set.
    • If cables are very often changed at the DDL Port (base) of the CONSULT-II unit, cable connector pin damage may result.
    • If there is connector pin damage, ECM reprogramming may fail. Permanent ECU damage can occur.
  15. Turn "ON" the ignition switch (do not start the engine).
    • CONSULT-II will turn "ON" automatically (see Figure 11  ).
    • Confirm that all electrical loads* (except for the ignition) are "OFF"  .
    • * Headlights, defroster, A/C, Audio (radio), and cellular telephone, etc.
    G07773479

    Figure 11 

    G07773480

    Figure 12 

  16. Roll down the driver's window part way, exit the vehicle, close the door, and hang the CONSULT II unit on the outside of the window (see Figure 12  ).
    • This step is necessary to ensure the CONSULT-II and DLC-II cable will not be disturbed during reprogramming.
    CAUTION: DO NOT  connect the CONSULT-II AC power supply for Steps 17, 18 and 19.

    Section 2: Confirm the vehicle's battery voltage and CONSULT-II "Charger Input" 

  17. Press SUB MODE  (see Figure 11  ) then:
    1. Press DOWN  4 times.
    2. Select BATTERY CHARGE. 
    G07773481

    Figure 13 

  18. Check the CONSULT-II's "Charger Input"  reading (see Figure 13  ).
    NOTE:
    • "Battery Voltage"  is the voltage level of CONSULT-II's battery.
    • "Charger Input"  is the voltage level of the vehicle's battery. (It must be above 12 volts.)  .
  19. The "Charger Input" reading MUST  be above 12 volts (see Figure 13  ).
    • A reading above 12 volts confirms;
      1. The DLC-II is properly connected to the vehicle,
      2. The vehicle battery voltage is sufficient for ECM reprogramming, and
      3. CONSULT-II has a sufficient power supply to perform ECM reprogramming.
    • If the vehicles battery voltage ("Charger Input") is below 12 volts, one or more of the following may be the cause:
    1. The battery charger you hooked up in section 1 is not charging the battery (poor connection or it is not working).
    2. The DLC-II does not have a good connection to the vehicle (not straight).
    3. The DLC-II cable may have a malfunction (damaged wire or pins).
    4. The CONSULT-II Converter (J44200-50/black box) is not working correctly (see Figure 10  ).
    CAUTION:
    • Do not attempt ECU Reprogramming if the vehicle's battery voltage is below 12 volts.
    • Permanent ECU damage can occur if the vehicle battery does not maintain the minimum voltage during ECU Reprogramming.

    If "Charger Input" is above 12 volts, power from the vehicle battery will keep CONSULT-II's power supply at the correct level during reprogramming. (see Figure 13  ).

    Section 3: ECM Reprogramming 

  20. Press INITIATE ECU REPROGRAM  (see Figure 14  ), then
    1. Press ECM 
    2. Review the precaution.
    3. Press NEXT 
    G07773482

    Figure 14 

  21. Press CHECK ECM P/N  to "confirm" (take note of) the current ECM part number (see Figure 15  ).
    NOTE: This is the vehicle's ECM part number BEFORE  Reprogramming.
    G07773483

    Figure 15 

  22. Press COPY  to print the current ECM part number for future reference.
  23. Press BACK  to return to the main menu.
  24. Select the ECM program to install (see Figure 16  ).
    G07773484

    Figure 16 

  25. The "REPROGRAM START"  window should appear (see Figure 17  ).
    NOTE: If you get an error message, refer to the ECU Reprogramming Software Operations Manual.
    G07773485

    Figure 17 

    CAUTION:

    CAUTION DURING REPROGRAMMING: 

    • Do not unplug CONSULT-II from the vehicle during reprogramming. Permanent ECM damage can occur.
    • Do not open any door or the trunk during reprogramming.
    • On some vehicles, the cooling fans may come on during reprogramming. This is a normal condition.  Do not disconnect the cooling fans. Forgetting to reconnect them may cause severe engine damage. A vehicle battery charger is needed* to maintain the battery voltage level during reprogramming.

    * You should have hooked up a battery charger in Section 1.

  26. Press START. 
    • After a few seconds, the window shown in Figure 18  will appear.
    • CONSULT-II will now turn "OFF" its screen backlight.
    • When the screen backlight goes "OFF", ECM reprogramming has started.
    NOTE: This process will take from 10 to 20 minutes.
    G07773486

    Figure 18 

    CAUTION: You must leave the vehicle and the CONSULT-II unit "undisturbed" (don't touch) until reprogramming is complete.
    NOTE: If CONSULT-II screen gives you an error message "Unmatch of Vehicle Data"  :
    • You tried to reprogram with an incorrect data file, or
    • You are trying to reprogram with a file that is already in the ECM.
  27. When the Reprogramming is complete, CONSULT-II will "beep", turn the screen backlight back ON and automatically print out a report (see Figure 19  ).
    • Remember it may take up to 20 minutes.
    • Attach the print-out to the repair order for future reference.
    G07773487

    Figure 19 

    CAUTION: If CONSULT-II prints "REPROGRAMMING UNEXPECTEDLY TERMINATED":
    • The ECM has been permanently damaged and will require replacement.
    • In this case, perform steps  Athrough G  .

    Do not start the engine with the damaged ECM installed. 

    This chart is provided as a reference to confirm the correct final ECM P/N after reprogramming.

    From → To 

    CURRENT/NEW ECM P/N CHART

    MODEL YEAR Vehicle Configuration Current ECM P/Ns Before Reprogramming New ECM P/N's
    Altima (L31) with 2.5L engine 2002 A/T with ASCD 23710-8J000, -8J001, -9J003, -9J004, -9J00A 23710-9J00B
    A/T 23710-8J010, -8J011, -9J008, -9J009, -9J03A 23710-9J03B
    M/T with ASCD 23710-8J060, -8J061, -9J013, -9J014,-9J01A 23710-9J01B
    MT 23710-8J070, -8J071, -9J018, -9J019,-9J04A 23710-9J04B
    2005 50 state A/T with ASCD (ULEV) 23710-9J505, -9J506, -9J507, -9J51A, -9J51B 23710-9J51C
    CAL A/T with ASCD (SULEV) 23710-9J560, -9J561, -9J562, -9J55A, -9J55C, -9J55D 23710-9J57E
    23710-9J55B, -9J55E 23710-9J59D
    50 state A/T (ULEV) 23710-9J500, -9J501, -9J502, -9J50A, -9J50B 23710-9J50C
    A/T CAL (SULEV) 23710-9J520, -9J521, -9J522, -9J54A, -9J54C, 9J54D 23710-9J56E
    23710-9J54B, -9J54E 23710-9J58D
    50 state M/T with ASCD (ULEV) 23710-9J515, -9J516, -9J517, -9J53A 23710-9J53B
    CAL M/T with ASCD (SULEV) 23710-9J570, -9J571, -9J572, -9J57B, -9J57C 23710-9J59C
    23710-9J57A, -9J57D 23710-9J59E
    50 state MT (ULEV) 23710-9J510,-9J511,-9J512,-9J52A 23710-9J52B
    CAL M/T (SULEV) 23710-9J565, -9J566, -9J567, -9J56B, -9J56C 23710-9J58C
    23710-9J56A, -9J56D 23710-9J58E
    2006 50 state A/T with ASCD (ULEV) 23710-ZD81A, -ZD81B, -ZD81C, -ZD81D,-ZD81E 23710-ZD89A
    CAL A/T with ASCD (SULEV) 23710-ZD85A, -ZD85B, -ZD85C, -ZD85D 23710-ZD85E
    50 state A/T (ULEV) 23710-ZD80A, -ZD80B, -ZD80C, -ZD80D, -ZD80E 23710-ZD88A
    A/T CAL (SULEV) 23710-ZD84A, -ZD84B, -ZD84C, -ZD84D 23710-ZD84E
    50 state M/T with ASCD (ULEV) 23710-ZD83A, -ZD83B, -ZD83C, -ZD83D 23710-ZD83E
    CAL M/T with ASCD (SULEV) 23710-ZD87A, -ZD87B, -ZD87C, -ZD87D 23710-ZD87E
    50 state MT (ULEV) 23710-ZD82A, -ZD82B, -ZD82C, -ZD82D 23710-ZD82E
    CAL M/T (SULEV) 23710-ZD86A, -ZD86B, -ZD86C, -ZD86D 23710-ZD86E
    Sentra (B15) with 2.5L engine 2002 A/T 23710-8U000, -8U001, -8U502, -8U503, -8U50A 23710-8U50B
    5 M/T 23710-8U010, -8U011, -8U512, -8U513, -8U51A 23710-8U51B
    6 M/T 23710-8U020, -8U021, -8U022, -8U023, -8U02A 23710-8U02B
    A/T with NATS 23710-8U040, -8U041, -8U542, -8U543, -8U54A 23710-8U54B
    5 M/T with NATS 23710-8U060, -8U061, -8U562, -8U563, -8U56A 23710-8U56B
    6 M/T with NATS 23710-8U070, -8U071, -8U072, -8U073, -8U07A 23710-8U07B
    2005 FED A/T 23710-6Z500 23710-6Z57A
    CAL A/T 23710-6Z510, -6Z53A 23710-6Z53B
    FED A/T with NATS 23710-6Z505 23710-6Z58A
    CAL A/T with NATS 23710-6Z515, -6Z54A 23710-6Z54B
    M/T with NATS 23710-6Z560, -6Z56A 23710-6Z56B
    M/T 23710-6Z520, -6Z55A 23710-6Z55B
    2006 A/T 23710-ZG50B, -ZG50C, -ZG50D, -ZG58A 23710-ZG58B
    A/T with NATS 23710-ZG51B, -ZG51C, -ZG51D, -ZG58E 23710-ZG58D
    M/T 23710ZG52B, -ZG52C, -ZG52D, -ZG59A 23710-ZG59B
    M/T with NATS 23710-ZG53B, -ZG53C, -ZG53D, -ZG59E 23710-ZG59D
    NOTE:
    • Part numbers for ECM programs are subject to change.
    • If a more recent part number is available for any of the ECM data (specified in the Chart above) the latest version should be used to complete this campaign repair.
    • ASIST contains the latest version of all ECM data.
  28. Press END  to return to the main menu.
  29. Turn the ignition switch "OFF" and CONSULT-II "OFF".
  30. Make sure the throttle is released; then operate the ignition as follows:
    G07773488

    Figure 20 

    The above ignition cycle will:

    • Reset ECM self learned Data.
    • Complete the Accelerator Pedal Released Position Learning.
    • Complete the Throttle Valve Closed Position Learning.

    Section 4: Perform ECM Reprogram Confirmation. 

  31. Remove the reprogramming CARD from CONSULT-II and insert the Diagnostic Card (red/white card).
  32. Start the engine.
  33. Make sure all DTCs are cleared (erased).
    • If necessary, erase any DTC's that may have stored during the reprogramming procedure.
  34. Idle Air Volume Learning Procedure:
    • For 2002 Models:  Perform the Idle Air Volume Leaning Procedure  (on the next page).
    • For 2005 and 2006  models: Idle Air Volume Leaning Procedure is not needed  .
  35. Check engine idle speed. (Target Idle Speed: No Load in P or N-700 ± 50 rpm.)
  36. Confirm the engine is operating normally.

IDLE AIR VOLUME LEARNING (IAVL) PROCEDURE

NOTE: The IAVL procedure will normally complete within 2 minutes after Procedure Start.
  1. Use CONSULT-II to confirm/perform the following Pre-Conditions:
    NOTE: The IAVL procedure will self-cancel if any of the following Pre-Conditions are not met and maintained for as long as the procedure is running. 
    ENGINE CONDITIONS REFERENCE CHART

    DATA MONITOR SIGNALS (ENGINE) PRE-CONDITIONS
    COOLAN TEMP/S [°C] OR [°F] Between 158 - 203°F (70 - 95°C).
    BATTERY VOLT [V] More than 12.9V at idle.
    P/N POSI SW [ON/OFF] ON (Transmission in either Neutral or Park).
    AIR COND SIG [ON/OFF] OFF (Air conditioner/HVAC switch off).
    LOAD SIGNAL [ON/OFF] OFF (Lighting switch and/or rear defogger off).
    COOLING FAN [ON/OFF] OFF (Engine cooling fan motor not running).
    PW/ST SIGNAL [ON/OFF] OFF (Steering wheel is straight ahead).
    VHCL SPEED SE [km/h] or [mph] 0 (Vehicle speed 0 mph).
    WORK SUPPORT SETTING (ENGINE)   
    CONSULT TARGET IDLE RPM ADJ 0 (Zero)

    After warming up the engine and confriming all of the above preconditions, then

  2. Turn the ignition OFF and wait at least 10 seconds.
  3. Start the engine and let the idle stabilize for about 30 seconds.
    NOTE: If the engine will not idle, hold the engine RPM at about 2000, then slowly bring it down to an idle.
  4. Using CONSULT-II, select WORK SUPPORT > IDLE AIR VOL LEARN.
  5. Touch START and wait 20 seconds to 2 minutes: CMPLT should be displayed.
    NOTE:
    • If INCMP is displayed within 2 minutes, or test is not finished within 2 minutes, Idle Air Volume Learning was not carried out successfully.
    • Make sure you set all of the preconditions exactly as shown in the chart above and performed steps 1 through 6 exactly as shown.
    • If needed, refer the IAVL diagnostic procedures in the Service Manual.
  6. Rev up the engine two or three times and allow it to return to idle.

PROGRAMMING UNEXPECTEDLY TERMINATED

(See step   27): 

CAUTION: Do not start the engine with the damaged ECM installed.
  1. Turn the ignition "OFF", turn CONSULT-II "OFF", and DISCONNECT THE NEGATIVE TERMINAL OF THE VEHICLE BATTERY.
  2. Attach the CONSULT-II print-out to the repair order for future reference.
  3. Replace the damaged ECM.
  4. Reconnect the negative battery cable.
  5. If the vehicle is equipped with NATS:
    • Some  models will require registration of the NATS keys.
    • See the appropriate TSB(s) or Service Manual (ESM) for NATS information and key registration procedures.
  6. Perform IAVL (IDLE AIR VOLUME LEARNING (IAVL) PROCEDURE ).
  7. Check the new ECM's current P/N; make sure it is the latest (newest) P/N-see step  21.
NOTE:
  • A new ECM from the parts department may not have the newest program.
  • If needed, return to step  5 of this procedure and reprogram the new ECM with the latest available P/N. Be careful to follow each step exactly as written.

CLAIMS INFORMATION

Submit a Campaign (CM) line claim using the following claims coding: 

"CM" I.D.: R0712 

For 2002 models: 

CLAIMS INFORMATION FOR 2002 MODELS

DESCRIPTION OP CODE FRT
Reprogram ECM & IAVL Procedure (2002 Only) R07120 0.7

OR 

For 2005 and 2006 models: 

CLAIMS INFORMATION FOR 2005 AND 2006 MODELS

DESCRIPTION OP CODE FRT
Reprogram ECM (2005 & 2006) R07121 0.5

OWNER'S LETTER

Dear Nissan owner:

This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Nissan has decided that a defect which relates to motor vehicle safety exists in some 2002 and 2005-2006 model year Nissan Altima and Sentra vehicles equipped with the 2.5 liter engine. Our records indicate that you own the Nissan vehicle identified by the Vehicle Identification Number on the cover of this notice.

Reason for Recall 

On some 2002 and 2005-2006 model year Nissan Altima and Sentra vehicles equipped with the 2.5 liter engine, there is a possibility that the engine might stop running while being driven due to the program in the Electronic Control Module (engine computer). If the engine stops running while driving, this could result in a crash without warning.

What Nissan Will Do 

In order to prevent this incident from occurring, your Nissan dealer will reprogram the Electronic Control Module. This free service should take about one hour to complete, but your Nissan dealer may require your vehicle for a longer period of time based upon their work schedule, or parts availability.

What You Should Do 

Contact your Nissan dealer at your earliest convenience in order to arrange an appointment to have your vehicle repaired. Please bring this notice with you when you keep your service appointment. Instructions have been sent to your Nissan dealer. If the dealer fails, or is unable to make the necessary repairs free of charge, you may contact the National Consumer Affairs Department, Nissan North America, Inc., P.O. Box 685003, Franklin, TN 37068-5003. The toll free number is 1-800-NISSAN1 (1-800-647-7261). You may also contact the Administrator, National Highway Traffic Safety Administration, 1200 New Jersey Avenue, SE., Washington, DC 20590; or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153); or go to http://www.safercar.gov.

Federal law requires that any vehicle lessor receiving this recall notice must forward a copy of this notice to the lessee within ten days.

Thank you for your cooperation. We are indeed sorry for any inconvenience this may cause you.