LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2005 >> Altima Base >> Repair and Diagnosis >> Engine Performance >> Engine Control System - Qr25DE >> DTC P1706: PNP Switch >> Diagnostic Procedure >> Procedure A

Procedure A

  1. CHECK STARTING SYSTEM 

    Turn ignition switch OFF, then turn it to START.

    Does starter motor operate? 

    Yes or No 

  2. CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I 
    1. Turn ignition switch OFF.
    2. Disconnect combination meter harness connector M24.
    3. Turn ignition switch ON.
    4. Check voltage between combination meter terminals 39 and ground with CONSULT-II or tester under the following conditions.
      Fig 1: Condition And Voltage Reference Chart
      G02526934Courtesy of NISSAN MOTOR CO., U.S.A.
      Fig 2: Checking Voltage Between Combination Meter Terminals 39 And Ground
      G02526935Courtesy of NISSAN MOTOR CO., U.S.A.

      OK or NG

      • OK: GO TO  9.
      • NG: GO TO 3.
  3. CHECK PNP SWITCH POWER SUPPLY CIRCUIT 
    1. Turn ignition switch OFF.
    2. Disconnect PNP switch harness connector.
    3. Turn ignition switch ON.
      Fig 3: Disconnecting PNP Switch Harness Connector
      G02526936Courtesy of NISSAN MOTOR CO., U.S.A.
    4. Check voltage between PNP switch terminal 3 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

      OK or NG

      • OK: GO TO  5.
      • NG: GO TO 4.
      Fig 4: Checking Voltage Between PNP Switch Terminal 3 And Ground
      G02526937Courtesy of NISSAN MOTOR CO., U.S.A.
  4. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors M71, F59
    • 10A fuse
    • Fuse block (J/B) connector M4
    • Harness for open or short between PNP switch and fuse

      : Repair open circuit or short to ground or short to power in harness or connectors.

  5. CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-I 
    1. Check harness continuity between PNP switch terminal 9 and combination meter terminal 39.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

    2. Also check harness for short to ground and short to power.

      OK or NG

      • OK: GO TO  7.
      • NG: GO TO 6.
  6. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors F58, M70
    • Harness for open or short between PNP switch and combination meter

      : Repair open circuit or short to ground or short to power in harness or connectors.

  7. CHECK PNP SWITCH 

    Refer to DTC P0705: PARK/NEUTRAL POSITION SWITCH .

    OK or NG

    • OK: GO TO 8.
    • NG: Replace PNP switch.
  8. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    : INSPECTION END 

  9. CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT-II 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check harness continuity between ECM terminal 102 and combination meter terminal 6.

      Refer to WIRING DIAGRAM .

      Continuity should exist. 

    4. Also check harness for short to ground and short to power.

    OK or NG

    • OK: GO TO  11.
    • NG: GO TO 10.
  10. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors M71, F59
    • Harness for open or short between ECM and combination meter

      : Repair open circuit or short to ground or short to power in harness or connectors.

  11. REPLACE COMBINATION METER 

    Refer to "COMBINATION METERS ".

    OK or NG

    • OK: GO TO 12.
    • NG: Replace combination meter
  12. CHECK INTERMITTENT INCIDENT 

    Refer to "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    : INSPECTION END