LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2005 >> Altima Base >> Repair and Diagnosis >> Engine Performance >> Engine Control System - Qr25DE >> DTC P1274: A/F Sensor 1 >> Diagnostic Procedure

Diagnostic Procedure

  1. CHECK GROUND CONNECTIONS 
    1. Turn ignition switch OFF.
    2. Loosen and retighten three ground screws on the body. Refer to "GROUND INSPECTION ".
      Fig 1: Retightening Ground Screws Of Body
      G02526814Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    • OK: GO TO 2.
    • NG: Repair or replace ground connections.
  2. RETIGHTEN AIR FUEL RATIO (A/F) SENSOR 1 

    Loosen and retighten the air fuel ratio (A/F) sensor 1.

    Tightening torque: 40 - 60 N.m (4.1 - 6.1 kg-m, 30 - 44 ft-lb) 

    : GO TO 3.

    Fig 2: Retightening Air Fuel Ratio (A/F) Sensor 1
    G02526815Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CLEAR THE SELF-LEARNING DATA 

    With CONSULT-II 

    1. Start engine and warm it up to normal operating temperature.
    2. Select "SELF-LEARNING CONT" in "WORK SUPPORT" mode with CONSULT-II.
    3. Clear the self-learning control coefficient by touching "CLEAR".
    4. Run engine for at least 10 minutes at idle speed.

      Is the 1st trip DTC P0172 detected? Is it difficult to start engine? 

      Fig 3: Display Work Support Mode Screen
      G02526816Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Start engine and warm it up to normal operating temperature.
    2. Turn ignition switch OFF.
    3. Disconnect mass air flow sensor harness connector, and restart and run engine for at least 3 seconds at idle speed.
    4. Stop engine and reconnect mass air flow sensor harness connector.
    5. Make sure DTC P0102 is displayed.
    6. Erase the DTC memory. Refer to "HOW TO ERASE EMISSION-RELATED DIAGNOSTIC INFORMATION ".
    7. Make sure DTC P0000 is displayed.
    8. Run engine for at least 10 minutes at idle speed.

      Is the 1st trip DTC P0172 detected? Is it difficult to start engine? 

      Fig 4: Identifying Mass Air Flow Sensor
      G02526817Courtesy of NISSAN MOTOR CO., U.S.A.

    Yes or No 

  4. CHECK HARNESS CONNECTOR 
    1. Turn ignition switch OFF.
    2. Disconnect A/F sensor 1 harness connector.
    3. Check harness connector for water.

      Water should not exit. 

    OK or NG

    • OK: GO TO 5.
    • NG: Repair or replace harness connector.
      Fig 5: Disconnecting A/F Sensor 1 Harness Connector
      G02526818Courtesy of NISSAN MOTOR CO., U.S.A.
  5. CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT 
    1. Turn ignition switch ON.
    2. Check voltage between A/F sensor 1 terminal 3 and ground with CONSULT-II or tester.

      Voltage: Battery voltage 

    OK or NG

    • OK: GO TO  7.
    • NG: GO TO 6.
      Fig 6: Checking Voltage Between A/F Sensor 1 Terminal 3 And Ground
      G02526819Courtesy of NISSAN MOTOR CO., U.S.A.
  6. DETECT MALFUNCTIONING PART 

    Check the following.

    • Harness connectors E21, F34
    • IPDM E/R harness connector E122
    • 15A fuse
    • Harness for open or short between A/F sensor 1 and fuse

      : Repair or replace harness or connectors.

  7. CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT 
    1. Turn ignition switch OFF.
    2. Disconnect ECM harness connector.
    3. Check harness continuity between the following terminals. Refer to WIRING DIAGRAM .
      A/F SENSOR 1 TERMINALS AND ECM TERMINALS REFERENCE

      A/F sensor 1 terminal ECM terminal
      1 16
      5 35
      6 56
      2 75

      Continuity should exist. 

    4. Check harness continuity between ECM terminals 16, 35, 56, 75 or A/F sensor 1 terminals 1, 2, 5, 6 and ground. Refer to WIRING DIAGRAM .

      Continuity should not exist. 

    5. Also check harness for short to power.

    OK or NG

    • OK: GO TO 8.
    • NG: Repair open circuit or short to ground or short to power in harness or connectors.
  8. CHECK A/F SENSOR 1 HEATER 

    Refer to "COMPONENT INSPECTION ".

    OK or NG

    • OK: GO TO 9.
    • NG: Replace A/F sensor 1.
  9. CHECK INTERMITTENT INCIDENT 

    Perform "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

    OK or NG

    • OK: Replace A/F sensor 1.
    • NG: Repair or replace.