LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 1082 (Automatic Drive Positioner) >> Automatic Drive Positioner >> Pedal Adjusting Switch Circuit Inspection

Pedal Adjusting Switch Circuit Inspection

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUNCTION 

    With CONSULT-II 

    With "PEDAL SW-FR, PEDAL SW-RR" on the DATA MONITOR, operate the pedal adjusting switch to check ON/OFF operation.

    CHECK FUNCTION

    Monitor item [OPERATION or UNIT] Contents
    PEDAL SW-FR "ON/OFF" Operation (ON)/open (OFF) status judged from the pedal adjusting switch (FR) signal is displayed.
    PEDAL SW-RR "ON/OFF" Operation (ON)/open (OFF) status judged from the pedal adjusting switch (RR) signal is displayed.
    Fig 1: Display DATA MONITOR
    G03500402Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Check voltage between driver seat control unit connector and ground.
    TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx)
    (+) (-)
    P2 15 (G/Y) Ground Pedal adjusting switch ON (RR operation) 0
    Pedal adjusting switch OFF Battery voltage
    30 (V) Pedal adjusting switch ON (FR operation) 0
    Pedal adjusting switch OFF Battery voltage

    OK or NG

    1. OK: Pedal adjusting switch circuit is OK.
    2. NG: GO TO 2.
    Fig 2: Checking Voltage Between Driver Seat Control Unit Connector & Ground
    G03500403Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK PEDAL ADJUSTING SWITCH CIRCUIT HARNESS CONTINUITY 
    1. Disconnect driver seat control unit and pedal adjusting switch.
    2. Check continuity between driver seat control unit connector P2 terminals 15 (G/Y), 30 (V) and pedal adjusting switch connector B22 terminals 2 (G/Y), 3 (V).
      1. 15 (G/Y) - 2 (G/Y): Continuity should exist. 
      2. 30 (V) - 3 (V): Continuity should exist. 
    3. Check continuity between driver seat control unit connector P2 terminals 15 (G/Y), 30 (V) and ground.
    1. 15 (G/Y) - Ground: Continuity should not exist. 
    2. 30 (V) - Ground: Continuity should not exist. 

    OK or NG

    1. OK: GO TO 3.
    2. NG: Repair or replace harness.
    Fig 3: Checking Continuity Between Driver Seat Control Unit Connector & Ground
    G03500404Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK PEDAL ADJUSTING SWITCH 

    Check continuity between pedal adjusting switch as follows.

    CHECK PEDAL ADJUSTING SWITCH

    Connector Terminals Condition Continuity
    (+) (-)
    B22 2 4 Pedal adjusting switch ON (RR operation) Yes
    Pedal adjusting switch OFF No
    3 Pedal adjusting switch ON (FR operation) Yes
    Pedal adjusting switch OFF No

    OK or NG

    1. OK: GO TO 4.
    2. NG: Replace pedal adjusting switch.
    Fig 4: Checking Continuity Between Pedal Adjusting Switch Terminal
    G03500405Courtesy of NISSAN MOTOR CO., U.S.A.
  4. CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT 

    Check continuity between pedal adjusting switch connector B22 terminal 4 (B) and ground.

    1. 4 (B) - Ground: Continuity should exist. 
    Fig 5: Checking Continuity Between Pedal Adjusting Switch Connector & Ground
    G03500406Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: Check the condition of the harness and connector.
    2. NG: Replace or replace harness.