LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 1082 (Automatic Drive Positioner) >> Automatic Drive Positioner >> Lifting Switch (Rear) Circuit Inspection

Lifting Switch (Rear) Circuit Inspection

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUNCTION 

    With CONSULT-II 

    With "LIFT RR SW-UP, LIFT RR SW-DN" on the DATA MONITOR, operate the rear lifting switch to check ON/OFF operation.

    CHECK FUNCTION

    Monitor item [OPERATION or UNIT] Contents
    LIFT RR SW-UP "ON/OFF" Operation (ON)/open (OFF) status judged from the RR lifter switch (UP) signal is displayed.
    LIFT RR SW-DN "ON/OFF" Operation (ON)/open (OFF) status judged from the RR lifter switch (DOWN) signal is displayed.
    Fig 1: Display DATA MONITOR
    G03500397Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch OFF.
    2. Check voltage between driver seat control unit connector and ground.
    TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx)
    (+) (-)
    P2 14(G/W) Ground Rear lifting switch ON (DOWN operation) 0
    Rear lifting switch OFF Battery voltage
    29 (R/W) Rear lifting switch ON (UP operation) 0
    Rear lifting switch OFF Battery voltage

    OK or NG

    1. OK: Rear lifting switch circuit is OK.
    2. NG: GO TO 2.
    Fig 2: Checking Voltage Between Driver Seat Control Unit Connector & Ground
    G03500398Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK LIFTING SWITCH (REAR) CIRCUIT HARNESS CONTINUITY 
    1. Disconnect driver seat control unit and power seat switch LH.
    2. Check continuity between driver seat control unit connector P2 terminals 14 (G/W), 29 (R/W) and power seat switch connector P8 terminals 2 (R/W), 8 (G/W).
      1. 14 (G/W)-8 (G/W): Continuity should exist. 
      2. 29 (R/W) - 2 (R/W): Continuity should exist. 
    3. Check continuity between driver seat control unit connector P2 terminals 14 (G/W), 29 (R/W) and ground.
      1. 14 (G/W)-Ground: Continuity should not exist. 
      2. 29 (R/W) - Ground: Continuity should not exist. 

      OK or NG

      1. OK: GO TO 3.
      2. NG: Repair or replace harness.
      Fig 3: Checking Continuity Between Driver Seat Control Unit Connector & Ground
      G03500399Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK LIFTING SWITCH (REAR) 

    Check continuity between power seat switch LH as follows.

    CHECK LIFTING SWITCH (REAR)

    Connector Terminals Condition Continuity
    (+) (-)
    P8 8 3 Lifting switch (rear) ON (DOWN operation) Yes
    Lifting switch (rear) OFF No
    2 Lifting switch (rear) ON (UP operation) Yes
    Lifting switch (rear) OFF No

    OK or NG

    1. OK: Check the condition of the harness and connector.
    2. NG: Replace power seat switch LH.
    Fig 4: Checking Continuity Between Power Seat Switch LH
    G03500400Courtesy of NISSAN MOTOR CO., U.S.A.