LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 1082 (Automatic Drive Positioner) >> Automatic Drive Positioner >> Door Mirror Switch (Mirror Switch) Circuit Check

Door Mirror Switch (Mirror Switch) Circuit Check

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK DOOR MIRROR SWITCH (MIRROR SWITCH) SIGNAL 

    With CONSULT-II 

    Check the operation on "MIR CON SW-UP/DN" and "MIR CON SW-RH/LH" in the DATA MONITOR.

    CHECK DOOR MIRROR SWITCH (MIRROR SWITCH) SIGNAL

    Monitor item [OPERATION or UNIT] Contents
    MIR CON SW -UP "ON/OFF" ON/OFF status judged from the door mirror switch (UP) signal is displayed.
    MIR CON SW -DN "ON/OFF" ON/OFF status judged from the door mirror switch (DOWN) signal is displayed.
    MIR CON SW -RH "ON/OFF" ON/OFF status judged from the door mirror switch (RIGHT) signal is displayed.
    MIR CON SW -LH "ON/OFF" ON/OFF status judged from the door mirror switch (LEFT) signal is displayed.
    Fig 1: Display DATA MONITOR
    G03500411Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT-II 

    1. Turn ignition switch ACC.
    2. Check voltage between automatic drive positioner control unit connector and ground.
    TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx)
    (+) (-)
    M41 3 (Y/B) Ground Mirror switch UP operation 0
    Mirror switch neutral position 5
    4 (G/B) Mirror switch LEFT operation 0
    Mirror switch neutral position 5
    19(L/B) Mirror switch DOWN operation 0
    Mirror switch neutral position 5
    20 (V) Mirror switch RIGHT operation 0
    Mirror switch neutral position 5

    OK or NG

    1. OK: Door mirror switch (mirror switch) circuit is OK.
    2. NG: GO TO 2.
    Fig 2: Checking Voltage Between Automatic Drive Positioner Control Unit Connector & Ground
    G03500412Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit and door mirror switch.
    3. Check continuity between automatic drive positioner control unit connector M41 terminal 3 (Y/B), 4 (G/B), 19 (L/B), 20 (V) and door mirror switch connector M66 terminal 1 (V), 2 (G/B), 3 (Y/B), 4 (L/B).
      1. 3 (Y/B) - 3 (Y/B): Continuity should exist. 
      2. 4 (G/B) - 2 (G/B): Continuity should exist. 
      3. 19 (L/B) - 4 (L/B): Continuity should exist. 
      4. 20 (V) - 1 (V): Continuity should exist. 
    4. Check continuity between automatic drive positioner control unit connector M41 terminal 3 (Y/B), 4 (G/B), 19 (L/B), 20 (V) and ground.
    1. 3 (Y/B) - Ground: Continuity should not exist. 
    2. 4 (G/B) - Ground: Continuity should not exist. 
    3. 19 (L/B) - Ground: Continuity should not exist. 
    4. 20 (V) - Ground: Continuity should not exist. 
    Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Connector & Ground
    G03500413Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: GO TO 3.
    2. NG: Repair or replace harness.
  3. CHECK DOOR MIRROR SWITCH (MIRROR SWITCH) 

    Check continuity between door mirror switch as follows.

    CHECK DOOR MIRROR SWITCH (MIRROR SWITCH)

    Connector Terminals Switch condition Continuity
    M7 1 7 Mirror switch RIGHT operation Yes
    Mirror switch neutral position No
    2 Mirror switch LEFT operation Yes
    Mirror switch neutral position No
    3 Mirror switch UP operation Yes
    Mirror switch neutral position No
    4 Mirror switch DOWN operation Yes
    Mirror switch neutral position No

    OK or NG

    1. OK: Check the condition of the harness and connector.
    2. NG: Replace door mirror switch.
    Fig 4: Check Continuity Between Door Mirror Switch Terminal
    G03500414Courtesy of NISSAN MOTOR CO., U.S.A.