LEMON Manuals: Even more car manuals for everyone
Home >> Nissan-Datsun >> 2004 >> Sentra SE-R >> Repair and Diagnosis >> External Pages >> Different car >> Section 1082 (Automatic Drive Positioner) >> Automatic Drive Positioner >> Door Mirror Switch (Changeover Switch) Circuit Check

Door Mirror Switch (Changeover Switch) Circuit Check

WARNING: This page is about a different car, the 2004 Nissan Quest. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK FUNCTION 

    With CONSULT-II 

    Check the operation on "MIR CHNG SW - R" or "MIR CHNG SW-L" in the DATA MONITOR.

    CHECK FUNCTION

    Monitor item [OPERATION or UNIT] Contents
    MIR CHNG S W-R "ON/OFF" ON/OFF status judged from the door mirror switch (switching to RIGHT) signal is displayed.
    MIR CHNG S W-L "ON/OFF" ON/OFF status judged from the door mirror switch (switching to LEFT) signal is displayed.
    Fig 1: Display DATA MONITOR
    G03500407Courtesy of NISSAN MOTOR CO., U.S.A.

    Without CONSULT 

    1. Turn ignition switch ACC.
    2. Check voltage between automatic drive positioner control unit connector and ground.
    TERMINAL VOLTAGE

    Connector Terminals (Wire color) Condition Voltage (V) (Approx)
    (+) (-)
    M41 2(L/R) Ground Changeover switch RIGHT position 0
    Changeover switch neutral position 5
    18 (Y) Changeover switch LEFT position 0
    Changeover switch neutral position 5

    OK or NG

    1. OK: Door mirror switch (changeover switch) is OK.
    2. NG: GO TO 2.
    Fig 2: Checking Voltage Between Automatic Drive Positioner Control Unit Connector & Ground
    G03500408Courtesy of NISSAN MOTOR CO., U.S.A.
  2. CHECK DOOR MIRROR SWITCH CIRCUIT HARNESS CONTINUITY 
    1. Turn ignition switch OFF.
    2. Disconnect automatic drive positioner control unit and door mirror switch.
    3. Check continuity between automatic drive positioner control unit connector M41 terminal 2 (L/R), 18 (Y/R) and door mirror switch connector M7 terminal 5 (L/R), 6 (Y/R).
      1. 2 (L/R) - 5 (L/R): Continuity should exist. 
      2. 18 (Y/R)-6 (Y/R): Continuity should exist. 
    4. Check continuity between automatic drive positioner control unit connector M41 terminal 2 (L/R), 18 (Y) and ground.
      1. 2 (L/R) - Ground: Continuity should not exist. 
      2. 18 (Y/R)-Ground: Continuity should not exist. 

      OK or NG

      1. OK: GO TO 3.
      2. NG: Repair or replace harness.
      Fig 3: Checking Continuity Between Automatic Drive Positioner Control Unit Connector & Ground
      G03500409Courtesy of NISSAN MOTOR CO., U.S.A.
  3. CHECK DOOR MIRROR SWITCH (CHANGEOVER SWITCH) 

    Check continuity between door mirror switch as follows.

    CHECK DOOR MIRROR SWITCH (CHANGEOVER SWITCH)

    Connector Terminals Condition Continuity
    (+) (-)
    M7 5 7 Changeover switch RIGHT position YES
    Changeover switch neutral position NO
    6 Changeover switch LEFT position YES
    Changeover switch neutral position NO
    Fig 4: Checking Continuity Between Door Mirror Switch Terminal
    G03500410Courtesy of NISSAN MOTOR CO., U.S.A.

    OK or NG

    1. OK: Check the condition of the harness and the connector.
    2. NG: Replace door mirror switch.